REMOVAL
Removal / installation · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
| 1.
REMOVE FRONT SEAT ASSEMBLY LH |
 |
(Click here)
| 2.
REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
|
 |
Apply protective tape as shown in the illustration.
Text in Illustration
*1
|
Protective Tape
|
Using a screwdriver, detach the 2 claws and remove the slide and vertical power seat switch knob.
- HINT:
- Tape the screwdriver tip before use.
| 3.
REMOVE RECLINING POWER SEAT SWITCH KNOB
|
 |
Using a screwdriver, detach the 2 claws and remove the reclining power seat switch knob.
Text in Illustration
*1
|
Protective Tape
|
- HINT:
- Tape the screwdriver tip before use.
| 4.
REMOVE FRONT SEAT CUSHION SHIELD LH
|
 |
Remove the 2 screws.
Disconnect the 2 rubber bands.
- Remove the 3 screws.
Detach the 2 claws and remove the front seat cushion shield LH together with the front inner No. 1 seat cushion shield LH.
for Driver Side:
Disconnect the connector.
| 5.
REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
|
 |
Disconnect the connectors and detach the clamps.
- Remove the nut and front seat inner belt assembly.
| 6.
REMOVE FRONT INNER SEAT CUSHION SHIELD LH
|
 |
Remove the screw.
Detach the 2 claws and clip, and then remove the front inner seat cushion shield LH.
| 7.
REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH
|
 |
Remove the 2 screws.
Move the front seatback board sub-assembly LH in the direction of the arrow to detach the 2 hooks and remove it.
| 8.
REMOVE SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System)
|
 |
Detach the 2 claws and disconnect the seat climate control blower LH.
Detach the 4 hooks and remove the seat climate control controller LH.
| 9.
REMOVE FRONT SEAT HEADREST SUPPORT
|
 |
Detach the 4 claws and remove the 2 front seat headrest supports.
| 10.
REMOVE SEATBACK COVER WITH PAD |
 |
- w/o Climate Control Seat System:
Disconnect the connector and detach the 2 wire harness clamps.
- w/ Climate Control Seat System:
Disconnect the 2 connectors and detach the 4 wire harness clamps.
- Remove the hog rings.
Text in Illustration
*1
|
Hog Ring
|
- Remove the nut and detach the seatback cover bracket.
Text in Illustration
*1
|
Seatback Cover Bracket
|
Detach the hooks and remove the seatback cover with pad.
| 11.
REMOVE FRONT SEPARATE TYPE SEATBACK COVER
|
 |
- Pass the seatback cover bracket through the hole of the front separate type seatback pad.
Text in Illustration
*1
|
Seatback Cover Bracket
|
- Remove the hog rings.
Detach the fastening tape and remove the front separate type seatback cover from the front separate type seatback pad.
Text in Illustration
*1
|
Fastening Tape
|
| 12.
REMOVE FRONT SEPARATE TYPE SEATBACK COVER (w/ Climate Control Seat System)
|
 |
- Pass the seatback cover bracket through the hole of the front separate type seatback pad.
Text in Illustration
*1
|
Seatback Cover Bracket
|
- Remove the hog rings and front separate type seatback cover from the front separate type seatback pad.
| 13.
REMOVE FRONT SEATBACK HEATER ASSEMBLY LH |
 |
- w/o Climate Control Seat System:
Cut off the tack pins and remove the front seatback heater assembly LH from the front separate type seatback cover.
- w/ Climate Control Seat System:
Cut off the tack pins and remove the front seatback heater assembly LH from the front separate type seatback cover.