2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH
  1. Set the front seat cushion heater assembly LH with the name stamp side facing the front separate type seat cushion cover.

  1. w/o Climate Control Seat System:
    Install the front seat cushion heater assembly LH to the front separate type seat cushion cover with new tack pins.

    B180732E02

    Text in Illustration 
    *1
    Tack Pin
    *2
    Front Separate Type Seat Cushion Cover
    *3
    Front Seat Cushion Heater Assembly LH
    *4
    Name Stamp

  1. w/ Climate Control Seat System:
    Install the front seat cushion heater assembly LH to the front separate type seat cushion cover with new tack pins.

    B298409E01

    Text in Illustration 
    *1
    Tack Pin
    *2
    Front Separate Type Seat Cushion Cover
    *3
    Front Seat Cushion Heater Assembly LH
    *4
    Name Stamp


2. INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER

B180733E02
  1. Using hog ring pliers, install the front separate type seat cushion cover to the front separate type seat cushion pad with new hog rings.

    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.


3. INSTALL SEAT CUSHION COVER WITH PAD
  1. Set the seat cushion cover with pad in place.

  1. B180708
    Attach the hooks to install the seat cushion cover with pad.

  1. Bend the 2 seat frame claws downward.

  1. for Front Passenger Side:

    1. B309117
      Attach the 2 clamps to connect the connector holder.

    2. Connect the connector.

  1. w/o Climate Control Seat System:

    1. B180707
      Connect the connector and attach the wire harness clamp.

    2. B180706
      Connect the connector and attach the 2 wire harness clamps.

  1. w/ Climate Control Seat System:

    1. B300511
      Attach the wire harness clamp.

    2. B299194
      Connect the 2 connectors and attach the 4 wire harness clamps.

  1. B180705
    Install the 2 clips.


4. INSTALL FRONT POWER SEAT SWITCH LH

B180704
  1. Install the front power seat switch LH with the 3 screws.

  1. w/ Seat Position Memory System:
    Connect the 2 connectors.

  1. w/o Seat Position Memory System:
    Connect the connector.


5. INSTALL FRONT INNER SEAT CUSHION SHIELD LH

B180703
  1. Attach the 2 claws and clip to install the front inner seat cushion shield LH.

  1. Install the screw.


6. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

B185875E01
  1. Install the front seat inner belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

  1. Connect the connectors and attach the clamps.


7. INSTALL FRONT SEAT CUSHION SHIELD LH
  1. for Driver Side:
    Connect the connector.

  1. B180700
    Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.

  1. Install the 3 screws.

  1. B180699
    Connect the 2 rubber bands.

  1. Install the 2 screws.


8. INSTALL RECLINING POWER SEAT SWITCH KNOB

B180734
  1. Attach the 2 claws to install the reclining power seat switch knob.


9. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

B180735
  1. Attach the 2 claws to install the slide and vertical power seat switch knob.


10. INSTALL FRONT SEAT ASSEMBLY LH
(Click here)
← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →