2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY
  1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

  1. Install the seat cushion heater with new tack pins.

    B181209E01


2. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

B182663E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B181184E01
    Attach the 3 pieces of fastening tape.


3. INSTALL SEAT CUSHION COVER WITH PAD
  1. Install the seat cushion cover with pad.

  1. w/ Rear Seat Side Airbag:
    Pass the side airbag wire harness through the hole in the seat cushion.

  1. w/ Seat Heater System:

    1. B184059
      Pass the seatback heater wire harness through the hole in the seat cushion.

    2. B184061
      Connect the 2 seat heater connectors.

  1. w/ Rear Seat Side Airbag:
    Attach the side airbag wire harness clamps.


4. INSTALL REAR SEAT UNDER TRAY COVER RH

B181181
  1. Attach the 4 claws to install the cover.

  1. Install the 2 screws.


5. INSTALL REAR UNDER SIDE COVER LH

B181178
  1. Attach the 2 claws and clip to install the cover.

  1. Install the 5 screws.


6. INSTALL REAR SEAT COVER

B181179
  1. Attach the 2 claws to install the cover.

  1. Install the 3 screws.

  1. B181177
    Attach the 12 claws.


7. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

  1. B181176
    Attach the cable clamp to connect the cable.

  1. B181175
    Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. w/ Rear Seat Side Airbag:
    Attach the wire harness clamp.

  1. w/ Seat Heater System:
    Attach the wire harness clamp.


8. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

B181174
  1. Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


9. INSTALL REAR NO. 2 SEAT PROTECTOR
  1. Install the wire harness, and attach the 2 claws to close the protector.

  1. B184060
    Attach the claw to install the protector to the seat hinge.

  1. Install the clip.

  1. B182658
    w/ Rear Seat Side Airbag:
    Attach the claw to install the wire harness connector.

  1. w/ Seat Heater System:
    Attach the claw to install the wire harness connector.


10. INSTALL REAR NO. 2 SEAT LEG SIDE COVER

  1. B181171
    Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

  1. B181170
    Attach the 3 claws to install the seat leg side cover.

  1. Install the 4 screws.


11. INSTALL UPPER SEAT TRACK RAIL COVER RH

B182664
  1. Attach the 2 claws to install the cover.


12. INSTALL UPPER SEAT TRACK RAIL COVER LH

B182665
  1. Attach the 2 claws to install the cover.


13. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

B181166
  1. Attach the 4 claws to install the cover.

  1. Install the 2 screws.


14. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B182666E01
  1. Attach the 3 claws in the order shown in the illustration to install the cover.

  1. Install the 2 screws.


15. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

B181164
  1. Install the release handle with the screw.


16. INSTALL SEAT ADJUSTER BOLT COVER

B181163
  1. Attach the 2 claws to install the cover.


17. INSTALL REAR NO. 1 SEAT ASSEMBLY RH
  1. Install the rear No. 1 seat assembly (Click here).

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →