INSTALLATION
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
| 1.
INSTALL REAR SEAT CUSHION HEATER ASSEMBLY |
 |
Set the seat cushion heater with the name stamp side facing the seat cushion cover.
Install the seat cushion heater with new tack pins.


| 2.
INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER
|
 |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
- Attach the 3 pieces of fastening tape.
| 3.
INSTALL SEAT CUSHION COVER WITH PAD
|
 |
Install the seat cushion cover with pad.
w/ Rear Seat Side Airbag:
Pass the side airbag wire harness through the hole in the seat cushion.
w/ Seat Heater System:
- Pass the seatback heater wire harness through the hole in the seat cushion.
- Connect the 2 seat heater connectors.
w/ Rear Seat Side Airbag:
Attach the side airbag wire harness clamps.
| 4.
INSTALL REAR SEAT UNDER TRAY COVER RH
|
 |
Attach the 4 claws to install the cover.
Install the 2 screws.
| 5.
INSTALL REAR UNDER SIDE COVER LH
|
 |
Attach the 2 claws and clip to install the cover.
Install the 5 screws.
| 6.
INSTALL REAR SEAT COVER
|
 |
Attach the 2 claws to install the cover.
Install the 3 screws.
- Attach the 12 claws.
| 7.
INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
|
 |
- Attach the cable clamp to connect the cable.
- Install the hinge with the 2 nuts.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
w/ Rear Seat Side Airbag:
Attach the wire harness clamp.
w/ Seat Heater System:
Attach the wire harness clamp.
| 8.
INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
|
 |
Install the hinge with the 2 nuts.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 9.
INSTALL REAR NO. 2 SEAT PROTECTOR
|
 |
Install the wire harness, and attach the 2 claws to close the protector.
- Attach the claw to install the protector to the seat hinge.
Install the clip.
- w/ Rear Seat Side Airbag:
Attach the claw to install the wire harness connector.
w/ Seat Heater System:
Attach the claw to install the wire harness connector.
| 10.
INSTALL REAR NO. 2 SEAT LEG SIDE COVER
|
 |
- Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.
- Attach the 3 claws to install the seat leg side cover.
Install the 4 screws.
| 11.
INSTALL UPPER SEAT TRACK RAIL COVER RH
|
 |
Attach the 2 claws to install the cover.
| 12.
INSTALL UPPER SEAT TRACK RAIL COVER LH
|
 |
Attach the 2 claws to install the cover.
| 13.
INSTALL REAR NO. 1 SEAT RECLINING COVER LH
|
 |
Attach the 4 claws to install the cover.
Install the 2 screws.
| 14.
INSTALL REAR NO. 1 SEAT RECLINING COVER RH
|
 |
Attach the 3 claws in the order shown in the illustration to install the cover.
Install the 2 screws.
| 15.
INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
|
 |
Install the release handle with the screw.
| 16.
INSTALL SEAT ADJUSTER BOLT COVER
|
 |
Attach the 2 claws to install the cover.
| 17.
INSTALL REAR NO. 1 SEAT ASSEMBLY RH |
 |
Install the rear No. 1 seat assembly (Click here).