2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


2. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover.


3. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
  1. Remove the rear No. 2 seat assembly (Click here).


4. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

B181672
  1. Detach the 6 clips and remove the support plate.


5. REMOVE REAR STEP COVER

B181673

HINT:
Use the same procedure to remove the step cover on the other side.

  1. Detach the 2 claws and remove the step cover.


6. REMOVE REAR DOOR SCUFF PLATE LH

B181674
  1. Remove the screw.

  1. Detach the 3 claws and 4 clips, and remove the scuff plate.


7. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

B186439

HINT:
Use the same procedure to remove the tonneau cover holder cap on the other side.

  1. Detach the 2 claws and remove the tonneau cover holder cap.


8. REMOVE REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat)

B181698
  1. Detach the 6 clips and remove the rear No. 2 seat cover bezel.


9. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

B182644
B181687

HINT:
When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

  1. Detach the 3 claws and remove the cover.

  1. B181689
    Remove the bolt and disconnect the rear seat outer belt floor anchor.

  1. B181691
    w/ Rear No. 2 Seat, for LH side:

    1. Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor LH.

  1. B181692
    w/ Rear No. 2 Seat, for RH side:

    1. Detach the 3 claws and remove the cover.

    2. B181693
      Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor RH.

  1. w/o Tonneau Cover:

    1. Remove the clip and bolt.

    2. Detach the 18 clips and 2 claws.

    3. w/o Rear Air Conditioning System:
      Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.

    4. w/ Rear Air Conditioning System:
      Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

      B186889

  1. w/ Tonneau Cover:

    1. Remove the screw and clip.

    2. Detach the 18 clips and 2 claws, and remove the quarter trim panel.

      B186437


10. REMOVE REAR FRONT QUARTER TRIM GARNISH LH

B181703
  1. Remove the screw.

  1. Detach the clip and 2 guides.

  1. Pass the seat belt anchor through the quarter trim garnish, and remove the quarter trim garnish.


11. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

B184510
  1. Remove the nut and seat belt shoulder anchor.

  1. B180641
    w/ Pretensioner:
    Disconnect the pretensioner connector as shown in the illustration.

  1. B180640E01
    Remove the 2 bolts and rear No. 1 seat outer belt.


12. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B184521
  1. Remove the 2 bolts and anchor plate.

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →