2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover.


4. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
  1. Remove the rear No. 2 seat assembly (Click here).


5. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

B181672
  1. Detach the 6 clips and remove the support plate.


6. REMOVE REAR STEP COVER

B181673

HINT:
Use the same procedure to remove the step cover on the other side.

  1. Detach the 2 claws and remove the step cover.


7. REMOVE REAR DOOR SCUFF PLATE LH

B181674
  1. Remove the screw.

  1. Detach the 3 claws and 4 clips, and remove the scuff plate.


8. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

B186439

HINT:
Use the same procedure to remove the tonneau cover holder cap on the other side.

  1. Detach the 2 claws and remove the tonneau cover holder cap.


9. REMOVE REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat)

B181698
  1. Detach the 6 clips and remove the rear No. 2 seat cover bezel.


10. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

B182644
B181687

HINT:
When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

  1. Detach the 3 claws and remove the cover.

  1. B181689
    Remove the bolt and disconnect the rear seat outer belt floor anchor.

  1. B181691
    w/ Rear No. 2 Seat, for LH side:

    1. Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor LH.

  1. B181692
    w/ Rear No. 2 Seat, for RH side:

    1. Detach the 3 claws and remove the cover.

    2. B181693
      Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor RH.

  1. w/o Tonneau Cover:

    1. Remove the clip and bolt.

    2. Detach the 18 clips and 2 claws.

    3. w/o Rear Air Conditioning System:
      Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.

    4. w/ Rear Air Conditioning System:
      Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

      B186889

  1. w/ Tonneau Cover:

    1. Remove the screw and clip.

    2. Detach the 18 clips and 2 claws, and remove the quarter trim panel.

      B186437


11. REMOVE REAR FRONT QUARTER TRIM GARNISH LH

B181703
  1. Remove the screw.

  1. Detach the clip and 2 guides.

  1. Pass the seat belt anchor through the quarter trim garnish, and remove the quarter trim garnish.


12. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

B184510
  1. Remove the nut and seat belt shoulder anchor.

  1. B180641
    w/ Pretensioner:
    Disconnect the pretensioner connector as shown in the illustration.

  1. B180640E01
    Remove the 2 bolts and rear No. 1 seat outer belt.


13. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B184521
  1. Remove the 2 bolts and anchor plate.

← REMOVAL (Sep 2011 – Dec 2011)INSPECTION (from Sep 2011) →