2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

  1. B183930
    Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

    NOTICE:
    If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate may be damaged.

  1. Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.

  1. B180934
    Using a T30 ''TORX'' socket, tighten the screw.

  1. Connect the connector.


2. INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

  1. B185061
    Attach the claw to install the rear door outside handle cover.

  1. B185067
    Using a T30 ''TORX'' socket, install the cover with the screw.


3. INSTALL REAR DOOR LOCK ASSEMBLY LH

  1. B183927
    Apply MP grease to the sliding parts of the rear door lock assembly.

  1. Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

  1. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

  1. Using a T30 ''TORX'' wrench, the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


4. INSTALL REAR DOOR SERVICE HOLE COVER LH
  1. Apply butyl tape to the door.

  1. B180918
    Pass the rear door lock remote control cable and rear door inside locking cable through a new rear door service hole cover.

    NOTICE:
    1. When installing the service hole cover, pull the links and connectors through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.

  1. B183933E02
    Connect the 2 connectors.

  1. Attach the 6 clamps.

  1. B180916E01
    Install the bolt as shown in the illustration.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


5. INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. E155902
    Connect the connector.

  1. Attach the claw of the courtesy light to the rear door trim.


6. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
  1. Connect the connector.

  1. B183925
    Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.

  1. B180912
    Attach the 4 claws and 9 clips to install the rear door trim board sub-assembly.

  1. Install the 3 screws.


7. INSTALL ASSIST GRIP COVER LH

  1. B183924
    Attach the 9 claws to install the door assist grip cover to the door trim panel.


8. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

  1. B183922
    Attach the 4 claws to install the bezel.


9. INSTALL REAR DOOR ARMREST BASE PANEL ASSEMBLY LH
  1. Connect the connector.

  1. B183923
    Attach the 7 claws to install the armrest base panel.


10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSPECTION (from Sep 2011)INSTALLATION (from Jan 2012) →