2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL DOOR CONTROL RECEIVER

  1. B181120
    Install the receiver with the bolt.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. Connect the connector.


2. INSTALL REAR UPPER PILLAR GARNISH RH

B184328
  1. w/o Power Back Door:

    1. Attach the 5 clips to install the rear upper pillar garnish.

  1. B194837E02
    w/ Power Back Door:

    1. Pass the power back door rod through the rear upper pillar garnish.

    2. Attach the 5 clips to install the rear upper pillar garnish.

  1. B195963
    Install the seat belt shoulder anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B187190
    Attach the 2 claws to close the seat belt shoulder anchor cover.


3. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

B182645

HINT:
When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

  1. w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. w/o Rear Air Conditioning System:
      Connect the rear seat lock control lever cable.

    2. w/ Rear Air Conditioning System:
      Connect the thermistor connector and rear seat lock control lever cable.

    3. Attach the 16 clips and 2 claws to install the quarter trim panel.

    4. Install the clip and bolt.

      Torque:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }


      B186890

  1. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

    1. Attach the 16 clips and 2 claws to install the quarter trim panel.

    2. Install the clip.

      B190220

  1. B181693
    w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. Install the rear No. 2 seat belt anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. B181692
      Attach the 3 claws to install the cover.

  1. B181690
    Install the rear No. 1 seat belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B181688
    Attach the 3 claws to install the cover.


4. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B190214

HINT:
Use the same procedure to install the rear seat cover cap on the other side.

  1. Attach the 3 claws to install the rear seat cover cap.


5. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

B186439

HINT:
Use the same procedure to install the tonneau cover holder cap on the other side.

  1. Attach the 2 claws to install the tonneau cover holder cap.


6. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

B181672
  1. Attach the 6 clips to install the support plate.


7. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


8. INSTALL REAR STEP COVER

B181673

HINT:
Use the same procedure to install the step cover on the other side.

  1. Attach the 2 claws to install the step cover.


9. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)
  1. Install the rear No. 2 seat assembly RH (Click here).


10. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)
  1. Install the rear No. 2 seat assembly RH (Click here).

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (Sep 2011 – Dec 2011) →