2011-2013 Land Cruiser · Service Manual Steering

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column (Click here).


1. FRONT WHEELS FACING STRAIGHT AHEAD

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disable the AUTO TILT AWAY function by changing the customize parameter (Click here).

    NOTICE:
    Record the current customize parameter setting (whether the AUTO TILT AWAY function is enabled or disabled) in order to restore the current setting after finishing the operation.

    HINT:
    Performing the above operation causes the AUTO TILT AWAY function to be disabled when the engine switch is turned off.

  1. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

  1. Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE LOWER NO. 3 STEERING WHEEL COVER

  1. B181563
    Detach the 2 claws and remove the steering wheel cover.


4. REMOVE LOWER NO. 2 STEERING WHEEL COVER

  1. B189186E01
    Detach the 2 claws and remove the steering wheel cover.


5. REMOVE STEERING PAD

  1. B187261E01
    Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.

  1. B181568
    Pull out the steering pad from the steering wheel, as shown in the illustration. Then support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector.

  1. Disconnect the 2 connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


6. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel set nut.

  1. C172673E01
    Put matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)


7. REMOVE LOWER STEERING COLUMN COVER

  1. C172674
    Remove the 3 screws.

  1. Detach the 2 claws to remove the lower steering column cover.

    NOTICE:
    Do not damage the tilt and telescopic switch.


8. REMOVE UPPER STEERING COLUMN COVER

  1. C172675
    Detach the 4 clips.

  1. Detach the claw to remove the upper steering column cover.


9. REMOVE TILT AND TELESCOPIC SWITCH

  1. C159804
    Disconnect the switch connector.

  1. Using a screwdriver, detach the claw and pull out the switch.

    NOTICE:
    Pushing on the claw too hard will break the claw.

    HINT:
    Tape the screwdriver tip before use.


10. REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

  1. C172676
    Disconnect the 5 connectors from the turn signal switch with spiral cable.

  1. C172677E01
    Using pliers, grip the claws of the clamp and remove the turn signal switch with spiral cable from the steering column.


11. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

  1. E155426E02
    Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 7 claws and remove the panel cushion.


12. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

  1. B181910
    Remove the clip.

  1. Remove the screw.

  1. Detach the 8 claws.

  1. Remove the panel pad and disconnect the connectors and 2 clamps.


13. REMOVE INSTRUMENT SIDE PANEL LH

E154740E06
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the instrument side panel.


14. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

E154744E04
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.


15. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

    B291251E01

    Text in Illustration 
    *A
    w/ Entry and Start System
    *B
    w/o Entry and Start System
    *1
    Protective Tape
    -
    -


16. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Multi-information Display)

B180017
  1. Detach the 9 claws.

  1. Disconnect the connector and remove the instrument cluster finish panel.


17. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-information Display)

B180016
  1. Detach the 9 claws and remove the instrument cluster finish panel.


18. REMOVE FRONT DOOR SCUFF PLATE LH

B181682
  1. Detach the 7 claws and 4 clips, and remove the scuff plate.


19. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B180655
  1. Remove the 2 screws.

  1. Detach the 3 claws.

  1. Disconnect the connectors and remove the No. 1 instrument panel under cover.


20. REMOVE COWL SIDE TRIM BOARD LH

B181911
  1. Remove the cap nut.

  1. Detach the 2 clips and remove the cowl side trim board.


21. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

B180295E02
  1. Using a screwdriver, detach the 2 claws and open the hole cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. w/ Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 16 claws.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 9 claws.

      B291250

  1. B180296
    for Automatic Air Conditioning System:

    1. Detach the 2 claws and remove the room temperature sensor.

  1. B181942
    Detach the 2 claws and disconnect the 2 control cables.

  1. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.


22. REMOVE NO. 1 SWITCH HOLE BASE

B180298
  1. Detach the 4 claws.

  1. Disconnect the connectors and remove the No. 1 switch hole cover.


23. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

  1. B189602E01
    Remove the 5 bolts and driver side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


24. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B180655
  1. Remove the 2 screws.

  1. Detach the 3 claws.

  1. Disconnect the connectors and remove the No. 1 instrument panel under cover.


25. REMOVE WIRE HARNESS PROTECTOR AND WIRE HARNESS

  1. C172657
    Detach the 3 claws to remove the wire harness protector and wire harness.


26. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY

E156901
  1. Remove the clip.

  1. Detach the 2 claws and remove the duct.


27. REMOVE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

  1. C179299E01
    Put matchmarks on the steering actuator and steering column.

  1. Remove the bolt.

  1. C172653
    Remove the 4 nuts and steering column.


28. DISCONNECT STEERING ACTUATOR ASSEMBLY

C180165
  1. While pushing the claws on both sides of the connector, move the lock in the direction of the arrow.

  1. Disconnect the connector.

  1. C179097
    Hold the clamp with needle nose pliers, then insert a screwdriver and turn it in the direction shown in the illustration to remove the clamp of the steering column hole cover.

  1. C172649E01
    Put matchmarks on the steering actuator and No. 2 steering intermediate shaft.

  1. Remove the bolt, and then pull out the actuator assembly toward the inside of the vehicle.


29. REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY

  1. C179099
    Remove the 4 bolts and nut with the steering column hole cover from the vehicle.


30. DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT

  1. C172652E01
    Loosen the bolt and remove the No. 2 intermediate shaft.

    NOTICE:
    It is possible to install the intermediate shaft to the same position it was removed from without placing matchmarks due to the dust cover part labeled A. Therefore, do not remove the dust cover from the steering link.

    HINT:
    If the dust cover is removed/installed or replaced, place matchmarks on the dust cover and steering link.

← ON-VEHICLE INSPECTION (from Jan 2012)REMOVAL (from Jan 2012) →