2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011


1. INSTALL FUEL TANK TO FILLER PIPE HOSE

  1. A176442E01
    Install the hose to the fuel sub tank as shown in the illustration.

    HINT:
    1. Align the fuel sub tank side mark with the hose side mark when installing the hose.

    2. A176441E01
      Tighten the hose clamp until the end of the hose clamp contacts the stopper as shown in the illustration.


2. INSTALL NO. 3 FUEL HOSE

  1. A176443E01
    Install the fuel hose to the fuel sub tank as shown in the illustration.

    HINT:
    1. Align the fuel sub tank side mark with the hose side mark when installing the hose.

    2. A176441E01
      Tighten the hose clamp until the end of the hose clamp contacts the stopper as shown in the illustration.


3. INSTALL FUEL TANK BREATHER HOSE

  1. A175083
    Install the breather hose to the fuel sub tank.


4. INSTALL FUEL AND EVAPORATION VENT TUBE SUB-ASSEMBLY

  1. A176321
    Install a new gasket to the fuel and evaporation vent tube.

  1. Install the fuel and evaporation vent tube with the 6 bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }


5. INSTALL FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

  1. A176323
    Install the 2 fuel tank evaporation vent tubes.


6. INSTALL FUEL HOSE

A176322

7. INSTALL FUEL SENDER GAUGE ASSEMBLY

  1. A175087
    Install a new gasket to the sender gauge.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Install the sender gauge with the 5 screws.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }


8. INSTALL FLOOR NO. 3 WIRE

  1. A175080
    Attach the wire harness clamp to the fuel sub tank.

  1. Connect the sender gauge connector.


9. INSTALL FUEL SUB TANK SUB-ASSEMBLY
  1. Set the fuel sub tank on a transmission jack and raise the fuel sub tank.

  1. A175079
    Connect the 2 fuel tank bands with the 2 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. A181396
    Connect the floor No. 3 wire connector.

  1. Attach the 3 wire harness clamps.


10. CONNECT FUEL TANK TO FILLER PIPE HOSE

  1. A175078
    Connect the hose to the filler pipe.


11. CONNECT NO. 3 FUEL HOSE

  1. A175077
    Connect the fuel hose to the filler pipe.


12. CONNECT FUEL TANK BREATHER HOSE

  1. A175076
    Connect the breather hose to the filler pipe.


13. CONNECT FUEL HOSE

A176421

14. CONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

  1. A176420
    Connect the 2 fuel tubes.


15. INSTALL FUEL TANK CAP ASSEMBLY

16. INSTALL NO. 1 SPARE WHEEL STOPPER

  1. A176385
    Install the spare wheel stopper with the 2 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }


17. INSTALL SPARE WHEEL CARRIER CROSSMEMBER AND SPARE WHEEL CARRIER BRACKET

  1. Install the spare wheel carrier crossmember and 2 brackets to the vehicle with the 6 bolts labeled C.

    Torque:
    for bolt C:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


    A176384E01

  1. Temporarily install the bolt labeled A, and then tighten the bolt labeled A and bolts labeled B.

    Torque:
    for bolt A:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for bolt B:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


18. INSTALL TAILPIPE ASSEMBLY
  1. Install the tailpipe to the 2 exhaust pipe supports.

  1. Install a new gasket to the center exhaust pipe.

  1. A167906E02
    Connect the tailpipe and center exhaust pipe with a new clamp.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    HINT:
    Install the clamp within the angle range shown in the illustration.


19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


20. INSPECT FOR FUEL LEAK
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and intelligent tester ON.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.


21. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

22. INSTALL SPARE TIRE
← REMOVAL (Sep 2011 – Dec 2011)COMPONENTS (Sep 2011 – Dec 2011) →