2011-2013 Land Cruiser · Service Manual Power Source / Network

SYSTEM DIAGRAM

System information · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


w/ Network Gateway ECU

HINT:
  1. The master cylinder solenoid (skid control ECU) stores steering sensor and yaw rate sensor assembly DTCs and performs DTC communication by receiving information from the steering sensor and yaw rate sensor assembly.
  2. The ECM uses the CAN communication system to perform DTC communication instead of the conventional communication line (SIL).

  1. SYSTEM DIAGRAM
    C258210E01

    No.
    ECU/Sensor Name
    1
    ECM
    2
    Network gateway ECU
    3
    Main body ECU (cowl side junction block LH)
    4
    DLC3
    5
    Air conditioning amplifier assembly
    6
    Center airbag sensor assembly
    7
    Multi-media module receiver assembly*1
    8
    Headlight swivel ECU assembly*2
    9
    Combination meter assembly
    10
    Certification ECU (smart key ECU assembly)*3
    11
    Multiplex tilt and telescopic ECU*4
    12
    Outer mirror control ECU assembly*5
    13
    Windshield wiper ECU*6
    14
    Position control ECU and switch*5
    15
    Accessory bus buffer
    16
    Power back door unit assembly (power back door ECU)*7
    17
    No. 2 main body ECU*7
    18
    Master cylinder solenoid (skid control ECU)
    19
    Yaw rate sensor assembly*8
    20
    Steering control ECU*9
    21
    Steering angle sensor*8
    22
    4WD control ECU
    23
    1. Parking assist ECU*10
    2. Clearance warning ECU assembly*11
    24
    Seat belt control ECU*12
    25
    Power steering ECU assembly*13
    26
    Distance control ECU assembly*14
    27
    Suspension control ECU*15
    28
    No. 1 CAN junction connector
    1. *1: w/ Navigation System
    2. *2: w/ Dynamic Headlight Auto Leveling
    3. *3: w/ Entry and Start System
    4. *4: w/ Power Tilt and Power Telescopic Steering Column System
    5. *5: w/ Seat Memory
    6. *6: w/ Rain Sensor
    7. *7: w/ Power Back Door System
    8. *8: w/ Vehicle Stability Control System
    9. *9: w/ Variable Gear Ratio Steering System
    10. *10: w/ Side Monitor System
    11. *11: w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System
    12. *12: w/ Pre-crash Safety System
    13. *13: for 1VD-FTV with DPF
    14. *14: w/ Dynamic Radar Cruise Control System
    15. *15: w/ Active Height Control Suspension

  2. V Bus
    C258211E01

  3. Movement Control Bus
    C258212E01

  4. MS Bus
    C258213E01


w/o Network Gateway ECU

HINT:
  1. The master cylinder solenoid (skid control ECU) stores steering sensor and yaw rate sensor assembly DTCs and performs DTC communication by receiving information from the steering sensor and yaw rate sensor assembly.
  2. The ECM uses the CAN communication system to perform DTC communication instead of the conventional communication line (SIL).

  1. SYSTEM DIAGRAM
    C258214E01

    No.
    ECU/Sensor Name
    1
    ECM
    2
    Combination meter assembly
    3
    Main body ECU (cowl side junction block LH)
    4
    DLC3
    5
    Air conditioning amplifier assembly
    6
    Center airbag sensor assembly*1
    7
    Multi-media module receiver assembly*2
    8
    4WD control ECU
    9
    Clearance warning ECU assembly*3
    10
    Master cylinder solenoid (skid control ECU)
    11
    Certification ECU (smart key ECU assembly)*4
    12
    Multiplex tilt and telescopic ECU*5
    13
    Accessory bus buffer
    14
    Outer mirror control ECU assembly*6
    15
    Windshield wiper ECU*7
    16
    Position control ECU and switch*6
    17
    Power back door unit assembly (power back door ECU)*8
    18
    No. 2 main body ECU*8
    1. *1: w/ Airbag System
    2. *2: w/ Navigation System
    3. *3: w/ TOYOTA Parking Assist-sensor System and w/o Side Monitor System
    4. *4: w/ Entry and Start System
    5. *5: w/ Power Tilt and Power Telescopic Steering Column System
    6. *6: w/ Seat Memory
    7. *7: w/ Rain Sensor
    8. *8: w/ Power Back Door System

  2. V Bus
    C258215E01

  3. MS Bus
    C258213E01

HINT:
The ECM uses the CAN communication system to perform DTC communication instead of the conventional communication line (SIL).

← SYSTEM DIAGRAM (Sep 2011 – Dec 2011)SYSTEM DESCRIPTION (Sep 2011 – Dec 2011) →