2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011


1. INSTALL KNOCK CONTROL SENSOR

  1. A185511E01
    Install the 2 sensors with the 2 nuts as shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 sensor connectors.


2. INSTALL CAMSHAFT POSITION SENSOR

  1. A124879
    Apply a light coat of engine oil to the O-ring.

    NOTICE:
    When reusing the sensor, inspect the O-ring.
    If the O-ring has scratches or cuts, replace the sensor.

  1. A175758
    Install the 2 sensors with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 2 sensor connectors.


3. INSTALL VENTILATION VALVE SUB-ASSEMBLY

  1. A092803E03
    Apply adhesive to 2 or 3 threads of the ventilation valve.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A183923E01
    Install the ventilation valve to the cylinder head cover sub-assembly LH.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

    HINT:
    After applying the specified torque, rotate the ventilation valve clockwise until the port facing in the direction indicated in the illustration.


4. INSTALL VENTILATION VALVE COVER
  1. Install the ventilation valve cover to the ventilation valve.


5. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH

  1. A175762
    Install a new O-ring to the camshaft timing oil control valve.

  1. Apply a light coat of engine oil to the O-ring.

  1. Install the camshaft timing oil control valve with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    1. Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
    2. Be careful that the O-ring is not cracked when installing the oil control valve.

  1. Connect the camshaft timing oil control valve connector and wire harness clamp.


6. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH

  1. A175761
    Install a new O-ring to the camshaft timing oil control valve.

  1. Apply a light coat of engine oil to the O-ring.

  1. Install the oil control valve with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    1. Do not allow foreign matter to contact the oil seal face of the oil control valve (connecting surface with cylinder head cover).
    2. Be careful that the O-ring is not cracked when installing the oil control valve.

  1. Connect the camshaft timing oil control valve connector.


7. INSTALL ENGINE OIL LEVEL SENSOR

  1. A178888
    Clean the oil level sensor installation surface.

  1. Install a new gasket and the oil level sensor with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the oil level sensor connector.


8. INSTALL CRANKSHAFT POSITION SENSOR

  1. A175763
    Install the sensor with the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the sensor connector.


9. INSTALL STARTER ASSEMBLY

  1. A177644
    Connect the starter wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the starter connector.

  1. Connect the starter to the cylinder block.

  1. Connect the ground wire with the bolt.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Connect the engine wire protector to the starter with the bolt.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. A177643
    Install the starter with the 2 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


10. INSTALL REAR WATER BY-PASS JOINT

  1. A160761
    A070482E02
    Install 2 new gaskets and the water by-pass joint with the 4 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    With the flat-bottom of each new gasket facing downward as shown in the illustration, install the 2 gaskets to the engine rear side.


11. INSTALL AIR PUMP WITH BRACKET AND AIR SWITCHING VALVE (w/ Secondary Air Injection System)

  1. A179560E01
    Install the air pump with bracket with the 2 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

  1. Connect the pressure sensor connector.

  1. Connect the air switching valve connector.


12. INSTALL NO. 2 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)

  1. A179559
    Install the hose.


13. INSTALL NO. 1 AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

  1. A182349
    Install a new gasket and the No. 1 air switching valve to the rear water by-pass joint with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the vacuum switching valve hose to the No. 1 air switching valve.


14. INSTALL NO. 2 AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

  1. A181856
    Install a new gasket and the No. 2 air switching valve to the rear water by-pass joint with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the vacuum switching valve hose to the No. 2 air switching valve.


15. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
  1. Apply soapy water to the O-ring.

  1. Install a new O-ring to the water by-pass pipe.

  1. A179561
    Push in the water by-pass pipe.

  1. Install the water by-pass pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the 2 vacuum switching valve hoses to the water by-pass pipe clamp.

  1. Connect the wire harness clamp.

  1. Connect the connector.


16. INSTALL FRONT WATER BY-PASS JOINT

  1. A178902E01
    Install 2 new gaskets and the water by-pass joint with the 4 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    With the flat-bottom of each new gasket facing downward as shown in the illustration, install the 2 gaskets to the engine front side.


17. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
  1. Install a new gasket to the sensor.

  1. A153484
    Using a 19 mm deep socket wrench, install the sensor.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }

  1. Connect the sensor connector.


18. INSTALL WATER INLET HOUSING

  1. A122971E03
    Apply soapy water to a new O-ring and install it to the water inlet housing.

  1. Apply seal packing in a continuous line to the places shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

    Standard seal diameter:
    2.0 to 3.0 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the water inlet housing within 3 minutes after applying seal packing.

  1. A122972E01
    Temporarily install the water inlet housing with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    Bolt Length:
    Item
    Length
    Bolt A
    77 mm (3.03 in.)
    Bolt B
    22 mm (0.866 in.)


19. CONNECT ENGINE WIRE

  1. Connect the ground wire to the No. 5 bearing cap and install the bolt, as shown in the illustration.

    A180828E01

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Connect the ground wire to the left side of the engine and install the bolt.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Connect the ground wire to the inside left side of the V-bank and install the bolt, as shown in the illustration.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Connect each ground wire to the cylinder head and cylinder head LH rear side and install the 2 bolts, as shown in the illustration.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


20. INSTALL IGNITION COIL ASSEMBLY

  1. A176582E01
    Install the 8 ignition coils with the 8 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 8 ignition coil connectors.


21. INSTALL INTAKE MANIFOLD
  1. Install the intake manifold (Click here).


22. INSTALL OIL FILTER ASSEMBLY

  1. A150110
    Clean and check the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.

  1. A150111E02
    Using SST, tighten the oil filter. Choose from the following to tighten the oil filter.
    SST
    09228-07501  

    1. Using a torque wrench, tighten the oil filter.

      Torque:
      17 N*m{ 175 kgf*cm , 13 ft.*lbf }

    2. Tighten the oil filter a 3/4 turn by hand or with a common wrench.


23. INSTALL OIL COOLER PIPE

  1. A108784E04
    Using needle-nose pliers, grip the claws of the clamps and slide the clamps to connect the 3 water by-pass hoses.

  1. Install the oil cooler pipe with the cap nut and bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


24. INSTALL OIL COOLER HOSE

  1. A178867
    Using needle-nose pliers, grip the claws of the clamps and slide the clamps to connect the oil cooler hose.


25. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

  1. A160775
    Install the engine mounting bracket with the 4 bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }


26. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

  1. A160774
    Install the engine mounting bracket with the 4 bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }


27. INSTALL FRONT ENGINE MOUNTING INSULATOR LH

  1. A176504
    Install the engine mounting insulator with the nut.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }


28. INSTALL FRONT ENGINE MOUNTING INSULATOR

  1. A176503
    Install the engine mounting insulator with the nut.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }


29. INSTALL NO. 2 WIRING HARNESS HEAT INSULATOR

  1. A160781
    Install the wiring harness heat insulator with the 2 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }


30. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH (w/o Secondary Air Injection System)

  1. A176364E01
    Place a new gasket on the cylinder head with the "L" mark facing the manifold side.

    NOTICE:
    Be careful of the installation direction.

  1. A167929E02
    Temporarily install the exhaust manifold with 8 new nuts, and then uniformly tighten the nuts in several steps, in the sequence shown in the illustration.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


31. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH (w/o Secondary Air Injection System)

  1. A176365E01
    Place a new gasket on the cylinder head with the "R" mark facing the manifold side.

    NOTICE:
    Be careful of the installation direction.

  1. A167927E02
    Temporarily install the exhaust manifold with 8 new nuts, and then uniformly tighten the nuts in several steps, in the sequence shown in the illustration.

    Torque:
    44 N*m{ 429 kgf*cm , 32 ft.*lbf }


32. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH (w/ Secondary Air Injection System)

  1. A176364E01
    Place a new gasket on the cylinder head with the "L" mark facing the manifold side.

    NOTICE:
    Be careful of the installation direction.

  1. A175005E01
    Temporarily install the exhaust manifold with 8 new nuts, and then uniformly tighten the nuts in several steps, in the sequence shown in the illustration.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


33. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH (w/ Secondary Air Injection System)

  1. A176365E01
    Place a new gasket on the cylinder head with the "R" mark facing the manifold side.

    NOTICE:
    Be careful of the installation direction.

  1. A175003E01
    Temporarily install the exhaust manifold with 8 new nuts, and then uniformly tighten the nuts in several steps, in the sequence shown in the illustration.

    Torque:
    44 N*m{ 429 kgf*cm , 32 ft.*lbf }


34. INSTALL NO. 3 AIR TUBE (w/ Secondary Air Injection System)

  1. A179564
    Install a new gasket and connect the No. 3 air tube to the exhaust manifold with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install a new gasket and connect the No. 3 air tube to the No. 2 air switching valve with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


35. INSTALL AIR TUBE SUB-ASSEMBLY RH (w/ Secondary Air Injection System)

  1. A179565
    Install a new gasket and connect the air tube to the exhaust manifold with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install a new gasket and connect the air tube to the No. 1 air switching valve with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


36. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A178868E02
    Apply a light coat of engine oil to a new O-ring.

  1. Install a new O-ring to the guide.

  1. Install the dipstick guide with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the dipstick.

← REASSEMBLY (Sep 2011 – Dec 2011)COMPONENTS (Sep 2011 – Dec 2011) →