2011-2013 Land Cruiser · Service Manual Vehicle Interior

DISASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE BLOWER ASSEMBLY
(Click here)

2. REMOVE NO. 4 AIR DUCT SUB-ASSEMBLY

E156866
  1. Remove the screw and duct.


3. REMOVE NO. 5 AIR DUCT SUB-ASSEMBLY

E156867
  1. Remove the screw and duct.


4. REMOVE ASPIRATOR (for Automatic Air Conditioning System)

E154374
  1. Detach the 2 claws and remove the aspirator.


5. REMOVE COOL BOX LIQUID TUBE (w/ Cool Box)

E154452
  1. Detach the clamp.

  1. Using SST, remove the piping clamp.

    SST
    09870-00025  

    1. E112919E02
      Attach SST to the piping clamp.

      HINT:
      Confirm the direction of the piping clamp claw and SST by referring to the illustration on the caution label.

    2. E112920E04
      Push down SST and release the clamp lock.

      NOTICE:
      Be careful not to deform the tubes when pushing SST.

    3. Pull SST slightly and push the release lever, then remove the piping clamp with SST.

    4. Remove the piping clamp from SST.

      Text in Illustration 
      *1
      Release Lever
      *a
      Push
      *b
      Pull

  1. Disconnect the tube.

    NOTICE:
    Cap the open fittings immediately to keep moisture or dirt out of the system.

  1. Remove the 2 O-rings from the tube.


6. REMOVE QUICK HEATER ASSEMBLY (w/ PTC Heater)
  1. Remove the 2 screws.

  1. E154697
    Detach the 3 clamps and remove the quick heater assembly (PTC heater assembly).


7. REMOVE AIR CONDITIONER HARNESS
  1. Disconnect the connectors.

  1. Detach the clamps and remove the harness.

    E154698E02

    Text in Illustration 
    *A
    for Automatic Air Conditioning System
    *B
    for 4 Zone Type


8. REMOVE AIR CONDITIONING RADIATOR ASSEMBLY

E154699
  1. Remove the screw and radiator bracket.

  1. Remove the radiator.


9. REMOVE COOLER EXPANSION VALVE (w/ Cool Box)

E154707
  1. Remove the packing.

  1. E154709
    Remove the butyl tape.

  1. E155177
    Using a 4 mm hexagon wrench, remove the hexagon bolt, screw and bracket.

  1. E154711
    Using a 4 mm hexagon wrench, remove the 2 hexagon bolts and No. 1 connector tube.

  1. Remove the 2 O-rings from the No. 1 connector tube.

  1. E154712
    Using a 4 mm hexagon wrench, remove the 2 hexagon bolts, No. 2 connector tube, expansion valve and No. 3 connector tube.

  1. Remove the 2 O-rings from the No. 2 connector tube.


10. REMOVE AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (w/ Cool Box)

E156749
  1. Remove the screw and bracket.

  1. Using a 4 mm hexagon wrench, remove the 2 hexagon bolts and air conditioner tube and accessory assembly.

  1. Remove the 2 O-rings from the air conditioner tube and accessory assembly.


11. REMOVE COOLER EXPANSION VALVE (w/o Cool Box)

E154708
  1. Remove the packing.

  1. E156750
    Using a 4 mm hexagon wrench, remove the 2 hexagon bolts, air conditioner tube and accessory assembly and expansion valve.

  1. Remove the 2 O-rings from the air conditioner tube and accessory assembly.

  1. Remove the 2 O-rings from the cooler evaporator.


12. REMOVE REAR AIR MIX DAMPER CONTROL SERVO MOTOR RH (for 4 Zone Type)

E154701
  1. Remove the 3 screws and servo motor.


13. REMOVE SERVO MOTOR

E154702
  1. Remove the 4 screws and servo motor unit.

  1. E154703
    for 4 Zone Type:
    Remove the front mode control servo motor RH.

    1. Remove the 2 screws.

    2. Detach the claw and remove the plate and servo motor.

      NOTICE:
      Be careful not to damage the claw of the plate.

  1. E154704
    Remove the control bypass damper control servo motor.

    1. Remove the 2 screws.

    2. Detach the claw and remove the plate and servo motor.

      NOTICE:
      Be careful not to damage the claw of the plate.

  1. E154705
    for Automatic Air Conditioning System:
    Remove the front air mix damper control servo motor RH.

    1. Remove the 2 screws.

    2. Detach the claw and remove the plate and servo motor.

      NOTICE:
      Be careful not to damage the claw of the plate.


14. REMOVE SERVO MOTOR

E154713
  1. Remove the 4 screws and servo motor unit.

  1. E237200
    Detach the 3 claws and remove the plate.

    NOTICE:
    Be careful not to damage the claw of the plate.

  1. E154715
    Remove the front mode control servo motor LH.

    1. Remove the 2 screws.

    2. Detach the claw and remove the plate and servo motor.

      NOTICE:
      Be careful not to damage the claw of the plate.

  1. E154716
    for Automatic Air Conditioning System:
    Remove the front air mix damper control servo motor LH.

    1. Remove the 2 screws.

    2. Detach the claw and remove the plate and servo motor.

      NOTICE:
      Be careful not to damage the claw of the plate.


15. REMOVE SERVO MOTOR (for Automatic Air Conditioning System)

E154717
  1. Remove the 3 screws and servo motor unit.

  1. E154718
    Remove the rear mode control servo motor.

    1. Remove the 2 screws.

    2. Detach the claw and remove the plate and servo motor.

      NOTICE:
      Be careful not to damage the claw of the plate.

  1. E154719
    Remove the rear air mix damper control servo motor LH.

    1. Remove the 2 screws.

    2. Detach the claw and remove the lever and servo motor.

      NOTICE:
      Be careful not to damage the claw of the lever.


16. REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
  1. Remove the 7 screws.

  1. Detach the 6 claws and remove the unit case.

  1. Remove the evaporator.

    E154720


17. REMOVE FRONT EVAPORATOR TEMPERATURE SENSOR

E236818
  1. Remove the front evaporator temperature sensor.

← REMOVAL (from Jan 2012)DISASSEMBLY (from Jan 2012) →