2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL NO. 3 CAMSHAFT SUB-ASSEMBLY

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. A076490E03
    Align the mark link (yellow) with the timing mark (2-dot mark) of the camshaft timing gear as shown in the illustration.

  1. Apply new engine oil to the thrust portions and journals of the camshaft.

  1. G038529E01
    Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.

  1. G038403E02
    Align the knock pin hole of the camshaft timing gear with the knock pin of the No. 3 camshaft, and insert the No. 3 camshaft into the camshaft timing gear.

  1. Temporarily install the camshaft timing gear set bolt.

  1. G038080E01
    Set the No. 3 camshaft onto the cylinder head LH with the cam lobes of the No. 2 cylinder facing downward as shown in the illustration.

  1. A076494E01
    Set the 4 bearing caps in their proper locations.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A076487E06
    Using several steps, install the 8 bearing cap bolts uniformly in the sequence shown in the illustration.

    Torque:
    for 10 mm head bolt:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    for 12 mm head bolt:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

  1. G038081E02
    Set the paint mark of the No. 1 chain between the timing marks of the camshaft timing gear.

  1. G038400E01
    Hold the hexagonal portion of the No. 3 camshaft with a wrench, and tighten the camshaft timing gear set bolt.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }


2. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

  1. A076289E01
    While pushing in the tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.

  1. G038082E03
    Temporarily install the camshaft timing sprocket and No. 3 chain tensioner with the bolt and align the mark links (yellow) with the timing marks (1-dot mark and 2-dot mark) of the camshaft timing gear and sprocket.

  1. Tighten the No. 3 chain tensioner bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


3. INSTALL NO. 4 CAMSHAFT SUB-ASSEMBLY

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. G038083E01
    Align the knock pin hole of the camshaft timing sprocket with the knock pin of the No. 4 camshaft, and insert the No. 4 camshaft into the camshaft timing sprocket.

  1. Temporarily install the camshaft timing sprocket set bolt.

  1. A076498E01
    Set the 4 bearing caps in their proper locations.

  1. Apply a light coat of engine oil to the threads of the bearing cap bolts.

  1. A076482E07
    Using several steps, install the 8 bearing cap bolts uniformly in the sequence shown in the illustration.

    Torque:
    for 10 mm head bolt:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    for 12 mm head bolt:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

  1. G038076E01
    Hold the hexagonal portion of the No. 4 camshaft with a wrench, and tighten the camshaft timing sprocket set bolt.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the No. 3 chain tensioner

  1. A076499E02
    Release the chain tension between the camshaft timing gear (RH bank) and crankshaft timing gear by turning the crankshaft pulley clockwise slightly.


4. INSTALL NO. 1 CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. A076518E03
    Align the mark link (yellow) with the timing mark (1-dot mark) of the camshaft timing gear as shown in the illustration.

  1. Apply new engine oil to the thrust portions and journals of the camshaft.

  1. A076519E01
    Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.

  1. G038084E01
    Align the knock pin hole of the camshaft timing gear with the knock pin of the No. 1 camshaft, and insert the No. 1 camshaft into the camshaft timing gear.

  1. Temporarily install the camshaft timing gear set bolt.

  1. G038085E01
    Set the No. 1 camshaft onto the cylinder head RH with the cam lobes of the No. 1 cylinder facing downward as shown in the illustration.

  1. A076522E01
    Set the 4 bearing caps in their proper locations.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A076515E08
    Using several steps, install the 8 bearing cap bolts uniformly in the sequence shown in the illustration.

    Torque:
    for 10 mm head bolt:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    for 12 mm head bolt:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

  1. G038086E02
    Rotate the No. 1 camshaft clockwise using a wrench so that the timing mark of the camshaft timing gear is aligned with the timing mark of the camshaft bearing cap.

  1. G038087E02
    Align the paint mark of the No. 1 chain with the timing mark of the camshaft timing gear.

  1. A076512E01
    Hold the hexagonal portion of the No. 1 camshaft with a wrench, and tighten the camshaft timing gear set bolt.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }


5. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A076286E01
    While pushing in the tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.

  1. G038088E02
    Temporarily install the camshaft timing sprocket and No. 2 chain tensioner with the bolt and align the mark links (yellow) with the timing marks (1-dot mark) of the camshaft timing gear and sprocket.

  1. Tighten the No. 2 chain tensioner bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


6. INSTALL NO. 2 CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. G038089E01
    Set the No. 2 camshaft onto the cylinder head RH with the cam lobes of the No. 1 cylinder facing upward as shown in the illustration.

  1. A076527E01
    Set the 4 bearing caps in their proper locations.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. A076510E16
    Using several steps, install the 8 bearing cap bolts uniformly in the sequence shown in the illustration.

    Torque:
    for 10 mm head bolt:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    for 12 mm head bolt:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

  1. G038090E02
    Rotate the No. 2 camshaft clockwise using a wrench so that the knock pin of the No. 2 camshaft is aligned with the knock pin hole of the camshaft timing sprocket.

  1. G038068E01
    Hold the hexagonal portion of the No. 2 camshaft with a wrench, and install the camshaft timing sprocket set bolt.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the No. 2 chain tensioner.


7. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A076294E04
    While turning the stopper plate of the tensioner clockwise, push in the plunger of the tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate in place.

  1. Install the chain tensioner with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Remove the bar from the chain tensioner.

  1. A076506E01
    Install a new gasket and the timing chain cover plate with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A076530E01
    Turn the crankshaft pulley 2 complete revolutions slowly, and align the notch with the timing mark "0" of the timing chain cover.

  1. G038065E10
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.


8. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A076530E01
    Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. G038065E10
    Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps as shown in the illustration.
    If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.


9. INSPECT VALVE CLEARANCE

  1. G036072E05
    Check the valves indicated in the illustration.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard Valve Clearance (Cold):
      Item
      Specified Condition
      Intake
      0.15 to 0.25 mm (0.00591 to 0.00984 in.)
      Exhaust
      0.29 to 0.39 mm (0.0114 to 0.0154 in.)

    2. Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.

  1. Turn the crankshaft 2/3 of a revolution (240°).

  1. G036073E04
    Check the valves indicated in the illustration.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard Valve Clearance (Cold):
      Item
      Specified Condition
      Intake
      0.15 to 0.25 mm (0.00591 to 0.00984 in.)
      Exhaust
      0.29 to 0.39 mm (0.0114 to 0.0154 in.)

    2. Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.

  1. Turn the crankshaft 2/3 of a revolution (240°).

  1. A076345E06
    Check the valves indicated in the illustration.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Standard Valve Clearance (Cold):
      Item
      Specified Condition
      Intake
      0.15 to 0.25 mm (0.00591 to 0.00984 in.)
      Exhaust
      0.29 to 0.39 mm (0.0114 to 0.0154 in.)

    2. Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.


10. ADJUST VALVE CLEARANCE

  1. A076530E01
    Set the No. 1 cylinder to TDC/compression.

    1. Turn the crankshaft pulley, and align the notch with the timing mark "0" of the timing chain cover.

    2. G038065E10
      Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps as shown in the illustration.
      If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.

    3. G038066E04
      Place paint marks on the chain links that correspond with the timing marks of the camshaft timing gears.

  1. Remove the No. 1 chain tensioner.

    NOTICE:
    1. Never rotate the crankshaft with the No. 1 chain tensioner removed.
    2. When rotating the camshaft with the No. 1 chain removed, turn the crankshaft counterclockwise 40° from TDC first.


    1. A076506E01
      Remove the 4 bolts, timing chain cover plate and gasket.

    2. A072958E04
      While rotating the stopper plate of the No. 1 chain tensioner clockwise, push in the plunger of the No. 1 chain tensioner as shown in the illustration.

    3. While rotating the stopper plate of the tensioner counterclockwise downward, insert a bar of φ3.5 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate in place.

    4. Remove the 2 bolts and No. 1 chain tensioner.

  1. Remove the No. 2 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. G038067E01
      While raising the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.

    2. G038068E01
      Hold the hexagonal portion of the No. 2 camshaft with a wrench, and remove the camshaft timing sprocket set bolt.

      NOTICE:
      Be careful not to damage the cylinder head and valve lifter with the wrench.

    3. Separate the camshaft timing sprocket from the No. 2 camshaft.

    4. G038069E01
      Rotate the camshaft counterclockwise using the wrench so that the cam lobes of the No. 1 cylinder face upward as shown in the illustration.

    5. A076510E13
      Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

    6. Remove the 4 bearing caps and No. 2 camshaft.

  1. G038070E01
    Remove the No. 2 chain tensioner.

    1. Remove the No. 2 chain tensioner bolt, No. 2 chain tensioner and camshaft timing sprocket.

  1. Remove the No. 1 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. G038072E01
      Hold the hexagonal portion of the No. 1 camshaft with a wrench, and loosen the camshaft timing gear set bolt.

      NOTICE:
      1. Be careful not to damage the cylinder head and valve lifter with the wrench.
      2. Do not disassemble the camshaft timing gear.

    2. G038071E01
      Slide the camshaft timing gear and separate the No. 1 chain from the camshaft timing gear.

    3. G038073E01
      Rotate the No. 1 camshaft counterclockwise using a wrench so that the cam lobes of the No. 1 cylinder face downward as shown in the illustration.

    4. A076515E01
      Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

    5. Remove the 4 bearing caps.

    6. G038074E01
      Remove the camshaft timing gear set bolt with the No. 1 camshaft lifted up, and then remove the No. 1 camshaft and camshaft timing gear with the No. 2 chain.

    7. A076517E01
      Tie the No. 1 chain with a string as shown in the illustration.

      NOTICE:
      Be careful not to drop anything inside the timing chain cover.

  1. Remove the No. 4 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. G038075E01
      While pushing down the No. 3 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.

    2. G038076E01
      Hold the hexagonal portion of the No. 4 camshaft with a wrench, and remove the camshaft timing sprocket set bolt.

      NOTICE:
      Be careful not to damage the cylinder head and valve lifter with the wrench.

    3. Separate the camshaft timing sprocket from the No. 4 camshaft.

    4. A076482E01
      Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

    5. Remove the 4 bearing caps and No. 4 camshaft.

  1. G038077E01
    Remove the No. 3 chain tensioner.

    1. Remove the No. 3 chain tensioner bolt, No. 3 chain tensioner and camshaft timing sprocket.

  1. Remove the No. 3 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. A076809E01
      Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration.

    2. Remove the 4 bearing caps.

    3. G038078E01
      Hold the No. 1 chain, and remove the No. 3 camshaft with camshaft timing gear and No. 2 chain.

    4. A076489E01
      Tie the No. 1 chain with a string as shown in the illustration.

      NOTICE:
      Be careful not to drop anything inside the timing chain cover.

  1. Remove the 24 valve lifters from the cylinder head LH and RH.

  1. A001082E01
    Determine the size of the valve lifter to be installed according to the following formulas or charts.

    1. Using a micrometer, measure the thickness of the removed lifter.

    2. Calculate the thickness of a new lifter so that the valve clearance comes within the specified value.

      T:
      Thickness of removed lifter

      A:
      Measured valve clearance

      N:
      Thickness of new lifter

      Intake:
      N = T + (A - 0.20 mm (0.00787 in.))

      Exhaust:
      N = T + (A - 0.34 mm (0.0131 in.))

    3. Select a new lifter with a thickness as close as possible to the calculated value.

      HINT:
      Lifters are available in 35 sizes in increments of 0.020 mm (0.000787 in.), from 5.060 mm (0.1992 in.) to 5.740 mm (0.2260 in.).


      A158682E02

      Intake valve clearance (Cold):
      0.15 to 0.25 mm (0.00591 to 0.00984 in.)
      EXAMPLE:
      The 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0157 in.). Replace the 5.250 mm (0.2067 in.) lifter with a No. 46 lifter.


      New Lifter Thickness:
      Lifter No.
      Thickness
      Lifter No.
      Thickness
      Lifter No.
      Thickness
      06
      5.060 mm (0.1992 in.)
      30
      5.300 mm (0.2087 in.)
      54
      5.540 mm (0.2181 in.)
      08
      5.080 mm (0.2000 in.)
      32
      5.320 mm (0.2094 in.)
      56
      5.560 mm (0.2189 in.)
      10
      5.100 mm (0.2008 in.)
      34
      5.340 mm (0.2102 in.)
      58
      5.580 mm (0.2197 in.)
      12
      5.120 mm (0.2016 in.)
      36
      5.360 mm (0.2110 in.)
      60
      5.600 mm (0.2205 in.)
      14
      5.140 mm (0.2024 in.)
      38
      5.380 mm (0.2118 in.)
      62
      5.620 mm (0.2213 in.)
      16
      5.160 mm (0.2031 in.)
      40
      5.400 mm (0.2126 in.)
      64
      5.640 mm (0.2220 in.)
      18
      5.180 mm (0.2039 in.)
      42
      5.420 mm (0.2134 in.)
      66
      5.660 mm (0.2228 in.)
      20
      5.200 mm (0.2047 in.)
      44
      5.440 mm (0.2142 in.)
      68
      5.680 mm (0.2236 in.)
      22
      5.220 mm (0.2055 in.)
      46
      5.460 mm (0.2150 in.)
      70
      5.700 mm (0.2244 in.)
      24
      5.240 mm (0.2063 in.)
      48
      5.480 mm (0.2157 in.)
      72
      5.720 mm (0.2252 in.)
      26
      5.260 mm (0.2071 in.)
      50
      5.500 mm (0.2165 in.)
      74
      5.740 mm (0.2260 in.)
      28
      5.280 mm (0.2079 in.)
      52
      5.520 mm (0.2173 in.)
      -
      -


      A158683E02

      Exhaust valve clearance (Cold):
      0.29 to 0.39 mm (0.0114 to 0.0154 in.)
      EXAMPLE:
      The 5.340 mm (0.210 in.) lifter is installed, and the measured clearance is 0.480 mm (0.0189 in.). Replace the 5.340 mm (0.210 in.) lifter with a No. 48 lifter.


      New Lifter Thickness:
      Lifter No.
      Thickness
      Lifter No.
      Thickness
      Lifter No.
      Thickness
      06
      5.060 mm (0.1992 in.)
      30
      5.300 mm (0.2087 in.)
      54
      5.540 mm (0.2181 in.)
      08
      5.080 mm (0.2000 in.)
      32
      5.320 mm (0.2094 in.)
      56
      5.560 mm (0.2189 in.)
      10
      5.100 mm (0.2008 in.)
      34
      5.340 mm (0.2102 in.)
      58
      5.580 mm (0.2197 in.)
      12
      5.120 mm (0.2016 in.)
      36
      5.360 mm (0.2110 in.)
      60
      5.600 mm (0.2205 in.)
      14
      5.140 mm (0.2024 in.)
      38
      5.380 mm (0.2118 in.)
      62
      5.620 mm (0.2213 in.)
      16
      5.160 mm (0.2031 in.)
      40
      5.400 mm (0.2126 in.)
      64
      5.640 mm (0.2220 in.)
      18
      5.180 mm (0.2039 in.)
      42
      5.420 mm (0.2134 in.)
      66
      5.660 mm (0.2228 in.)
      20
      5.200 mm (0.2047 in.)
      44
      5.440 mm (0.2142 in.)
      68
      5.680 mm (0.2236 in.)
      22
      5.220 mm (0.2051 in.)
      46
      5.460 mm (0.2150 in.)
      70
      5.700 mm (0.2244 in.)
      24
      5.240 mm (0.2063 in.)
      48
      5.480 mm (0.2157 in.)
      72
      5.720 mm (0.2252 in.)
      26
      5.260 mm (0.2071 in.)
      50
      5.500 mm (0.2165 in.)
      74
      5.740 mm (0.2260 in.)
      28
      5.280 mm (0.2079 in.)
      52
      5.520 mm (0.2173 in.)
      -
      -

  1. Install the No. 3 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. A076490E05
      Align the mark link (yellow) with the timing mark (2-dot mark) of the camshaft timing gear shown in the illustration.

    2. Apply a light coat of engine oil to the thrust portions and journals of the No. 3 camshaft.

    3. G038079E01
      Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.

    4. G038080E01
      Set the No. 3 camshaft onto the cylinder head LH with the cam lobes of the No. 2 cylinder facing downward as shown in the illustration.

    5. Apply a light coat of engine oil to the 4 bearing caps.

    6. A076494E01
      Set the 4 bearing caps in their proper locations.

    7. Apply a light coat of engine oil to the threads of the 8 bearing cap bolts.

    8. A076487E06
      Uniformly install the 8 bearing cap bolts in several steps in the order shown in the illustration.

      Torque:
      for 10 mm head bolt:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
      for 12 mm head bolt:
      24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    9. G038081E03
      Set the paint mark of the No. 1 chain between the timing marks of the camshaft timing gear.

  1. A076289E01
    Install the No. 3 chain tensioner.

    1. While pushing in the tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.

    2. G038082E04
      Temporarily install the camshaft timing sprocket and No. 3 chain tensioner with the bolt and align the mark links (yellow) with the timing marks (1-dot mark and 2-dot mark) of the camshaft timing gear and sprocket.

    3. Tighten the No. 3 chain tensioner bolt.

      Torque:
      21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the No. 4 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. Apply a light coat of engine oil to the thrust portions and journals of the No. 4 camshaft.

    2. Apply a light coat of engine oil to the threads and under the head of the camshaft timing sprocket set bolt.

    3. G038083E01
      Align the knock pin hole on the camshaft timing sprocket with the knock pin of the No. 4 camshaft, and insert the No. 4 camshaft into the camshaft timing sprocket.

    4. Temporarily install the camshaft timing sprocket set bolt.

    5. A134498
      Set the 4 bearing caps in their proper locations.

    6. Apply a light coat of engine oil to the threads and under the heads of the 8 bearing cap bolts.

    7. A076482E07
      Uniformly install the 8 bearing cap bolts in several steps in the order shown in the illustration.

      Torque:
      for 10 mm head bolt:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
      for 12 mm head bolt:
      24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    8. G038076E01
      Hold the hexagonal portion of the No. 4 camshaft with a wrench, and tighten the camshaft timing sprocket set bolt.

      Torque:
      100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

    9. Remove the pin from the No. 3 chain tensioner.

  1. Install the No. 1 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. A076518E05
      Align the mark link (yellow) with the timing mark (1-dot mark) of the camshaft timing gear as shown in the illustration.

    2. Apply a light amount of engine oil to the thrust portions and journals of the camshaft.

    3. A076519E01
      Temporarily put the No. 1 chain on the No. 2 chain of the camshaft timing gear.

    4. G038084E01
      Align the knock pin hole of the camshaft timing gear with the knock pin of the No. 1 camshaft, and insert the No. 1 camshaft into the camshaft timing gear.

    5. Apply a light coat of engine oil to the threads and under the head of the camshaft timing gear set bolt.

    6. Temporarily install the camshaft timing gear set bolt.

    7. G038085E02
      Set the No. 1 camshaft onto the cylinder head RH with the cam lobes of the No. 1 cylinder facing downward as shown in the illustration.

    8. Apply a light coat of engine oil to the 4 bearing caps.

    9. A076522E01
      Set the 4 bearing caps in their proper locations.

    10. Apply a light coat of engine oil to the threads and under the heads of the 8 bearing cap bolts.

    11. A076515E08
      Uniformly install the 8 bearing cap bolts in several steps in the order shown in the illustration.

      Torque:
      for 10 mm head bolt:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
      for 12 mm head bolt:
      24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    12. G038086E03
      Rotate the No. 1 camshaft clockwise using the hexagonal portion of the No. 1 camshaft so that the timing mark of the camshaft timing gear is aligned with the timing mark of the camshaft bearing cap.

    13. G038087E03
      Align the paint mark of the No. 1 chain with the timing mark of the camshaft timing gear.

    14. G038072E01
      Hold the hexagonal portion of the No. 1 camshaft with a wrench, and tighten the camshaft timing gear set bolt.

      Torque:
      100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. A076286E01
    Install the No. 2 chain tensioner.

    1. While pushing in the tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.

    2. G038088E03
      Temporarily install the camshaft timing sprocket and No. 2 chain tensioner with the bolt and align the mark links (yellow) with the timing marks (1-dot mark and 2-dot mark) of the camshaft timing gear and sprocket.

    3. Tighten the No. 2 chain tensioner bolt.

      Torque:
      21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the No. 2 camshaft.

    NOTICE:
    As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.


    1. Apply a light coat of engine oil to the thrust portions and journals of the No. 2 camshaft.

    2. G038089E01
      Set the No. 2 camshaft onto the cylinder head RH with the cam lobes of the No. 1 cylinder facing upward as shown in the illustration.

    3. Apply a light coat of engine oil to the 4 bearing caps.

    4. A134509
      Set the 4 bearing caps in their proper locations.

    5. Apply a light coat of engine oil to the threads and under the heads of the 8 bearing cap bolts.

    6. A076510E14
      Uniformly install the 8 bearing cap bolts in several steps in the order shown in the illustration.

      Torque:
      for 10 mm head bolt:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
      for 12 mm head bolt:
      24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    7. G038090E03
      Rotate the No. 2 camshaft clockwise using a wrench so that the knock pin of the No. 2 camshaft is aligned with the knock pin hole of the camshaft timing sprocket.

    8. Apply a light coat of engine oil to the threads and under the head of the camshaft timing sprocket set bolt.

    9. G038068E01
      Hold the hexagonal portion of the No. 2 camshaft with a wrench, and install the camshaft timing sprocket set bolt.

      Torque:
      100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

    10. Remove the pin from the No. 2 chain tensioner.

  1. A076294E06
    Install the No. 1 chain tensioner.

    1. While turning the stopper plate of the tensioner clockwise, push in the plunger of the tensioner as shown in the illustration.

    2. While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate in place.

    3. Apply a light coat of engine oil to the threads and under the heads of the 2 No. 1 chain tensioner bolts.

    4. Install the No. 1 chain tensioner with the 2 bolts.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    5. Remove the bar from the chain tensioner.

    6. A076506E01
      Install a new gasket and the timing chain cover plate with the 4 bolts.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    7. A076530E01
      Turn the crankshaft pulley 2 complete revolutions slowly, and align the notch with the timing mark "0" of the timing chain cover.

    8. G038065E10
      Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps as shown in the illustration.


11. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.

  1. A076311E06
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the head cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.

  1. A072944E02
    Temporarily install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


12. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.

  1. A076310E07
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2 to 3 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the head cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.

  1. A072943E02
    Temporarily install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


13. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 6 ignition coils with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 6 connectors to the 6 ignition coils.


14. INSTALL INTAKE AIR SURGE TANK

NOTICE:
Do not apply oil to the bolts and nuts listed below: :
Oil Application Prohibited Bolt/Nut
Bolt for surge tank and intake manifold
Nut for surge tank and intake manifold

  1. Install a new gasket to the intake air surge tank.

  1. A178940E02
    Using an 8 mm hexagon wrench, install the intake air surge tank with the 4 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. A178938
    Install the No. 2 surge tank stay with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A178939
    for Manual Transmission:

    1. Install the bracket to the No. 2 surge tank stay with the nut.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A178937
    Install the No. 1 surge tank stay with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A178936
    Install the oil baffle plate with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the bracket to the No. 1 surge tank stay with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A178935
    Attach the wire harness clamp.

  1. A151767
    Install the throttle body bracket with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A185262
    Connect the vacuum switching valve (for ACIS) connector.

  1. Attach the 2 wire harness clamps.

  1. A178934
    Connect the No. 1 ventilation hose.

  1. Connect the purge VSV connector.

  1. Connect the purge line hose.

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. A151857E01
    Connect the No. 4 and No. 5 water by-pass hose.

    HINT:
    Connect the hoses so that the direction of the hose clamps is as shown in the illustration.

  1. Connect the throttle body connector.


15. INSTALL AIR CLEANER ASSEMBLY

  1. A151811E02
    Install the air cleaner assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the hose clamp.

    HINT:
    Tighten the hose clamp until it reaches the specified protrusion height labeled A shown in the illustration.

    Standard protrusion height:
    Less than 0.5 mm (0.0197 in.)

  1. A185261
    Connect the MAF meter connector.

  1. Attach the 2 wire harness clamps.

  1. Connect the vacuum hose.

  1. A151812
    Attach the hose clamp.

  1. Connect the No. 2 ventilation hose.


16. CONNECT NO. 2 AIR CLEANER HOSE

  1. A184327E01
    Align the protrusion of the pre-cleaner with the groove of the No. 2 air cleaner hose as shown in the illustration.

  1. A178933E01
    Tighten the 2 hose clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Tighten the clamp until the end of the clamp band is within both limit marks.


17. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified condition
    for Automatic transmission
    w/o Rear Heater
    11.2 liters (11.8 US qts, 9.9 Imp. qts)
    w/ Rear Heater
    14.4 liters (15.2 US qts, 12.7 Imp. qts)
    for Manual transmission
    w/o Rear Heater
    12.0 liters (12.7 US qts, 10.6 Imp. qts)
    w/ Rear Heater
    14.6 liters (15.4 US qts, 12.8 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. A174295E01
    Slowly pour coolant into the radiator reservoir until it reaches the F line.

  1. Install the reservoir cap.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Set the air conditioning as follows while warming up the engine.

    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves. Heat areas on the parts may injure your hands.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A174297E01
    Check that the coolant level is between the F and L lines.
    If the coolant level is below the L line, repeat all of the procedures above.
    If the coolant level is above the F line, drain coolant so that the coolant level is between the F and L lines.


18. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A174294
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.


19. INSTALL UPPER RADIATOR SUPPORT SEAL

  1. B180889
    Install the radiator support seal with the 7 clips.


20. INSTALL V-BANK COVER

  1. A174359
    Install the V-bank cover with the 2 cap nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


21. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Install the under cover with the 10 bolts.


22. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


23. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Push in the clip indicated by the arrow in the illustration to install the fender splash shield.

  1. Install the 3 bolts and screw.


24. INSPECT IGNITION TIMING

NOTICE:
  1. Turn all electrical systems off.
  1. Perform the inspection when the cooling fan motor is turned off.

  1. Warm up the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / IGN Advance.

    3. Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idling (transmission in neutral position and A/C switch off)

    4. Check that the ignition timing advances immediately when the engine speed is increased.

  1. H102392E79
    When not using the intelligent tester:

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Be sure not to improperly connect the terminals. This may damage the engine.

    2. Remove the air cleaner cap.

    3. A158636
      Pull out the wire harness shown in the illustration.

    4. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      1. Use a timing light that detects primary signals.
      1. After checking, be sure to wrap the wire harness with tape.

    5. A076316E01
      Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idling (transmission in neutral position and A/C switch off)

    6. Remove SST from the DLC3.

    7. Inspect the ignition timing during idling.

      Standard ignition timing:
      7 to 24° BTDC @ idling (transmission in neutral position and A/C switch off)

    8. Disconnect the timing light from the engine.

    9. Install the air cleaner cap.

← REMOVAL (from Jan 2012)INSTALLATION (from Jan 2012) →