2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE FAN SHROUD
(Click here)

2. REMOVE INTAKE AIR SURGE TANK
(Click here)

3. REMOVE AIR TUBE (w/ Secondary Air Injection System)

  1. A223569
    Remove the 2 bolts, 2 nuts and air tube.

  1. Remove the 2 gaskets.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.


4. REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)

  1. A223563
    Remove the 2 bolts, 2 nuts and No. 2 air tube.

  1. Remove the 2 gaskets.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.


5. REMOVE NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A267738
    Disconnect the No. 1 emission control valve set connector.

  1. Disconnect the No. 1 air hose from the No. 1 emission control valve set.

  1. A223570
    Remove the 3 nuts and No. 1 emission control valve set.


6. REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A223562
    Disconnect the No. 2 emission control valve set connector.

  1. Disconnect the No. 3 air hose.

  1. A223564
    Remove the 3 nuts and No. 2 emission control valve set.


7. REMOVE IGNITION COIL ASSEMBLY

  1. A272605E01
    Disconnect the 6 ignition coil connectors.
    Text in Illustration 
    *A
    Bank 1
    *B
    Bank 2

  1. Remove the 6 bolts and 6 ignition coils.


8. DISCONNECT VANE PUMP ASSEMBLY

  1. A270981
    Disconnect the connector.

  1. Detach the wire harness clamp.

  1. A223015
    Remove the 2 bolts and disconnect the vane pump.


9. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A223006
    Remove the 2 bolts and 2 No. 2 idler pulleys.


10. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A272724
    Remove the 3 bolts and heat insulator.


11. REMOVE GENERATOR ASSEMBLY

  1. A267518
    Disconnect the generator connector.

  1. Open the terminal cap.

  1. Remove the nut and disconnect the generator wire from terminal B.

  1. Remove the bolt and disconnect the wire harness clamp bracket.

  1. A267519
    Remove the bolt and disconnect the generator bracket.

  1. A222883
    Remove the 2 bolts and generator.

  1. A222885
    Remove the bolt and generator bracket.


12. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A270151
    Remove the engine oil level dipstick.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.


13. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A223013
    Disconnect the 2 hoses.

  1. Remove the 3 bolts and water by-pass pipe.


14. REMOVE NO. 1 OIL PIPE

  1. A223691
    Remove the 2 oil pipe unions, oil control valve filter LH, 3 gaskets and No. 1 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


15. REMOVE NO. 2 OIL PIPE

  1. A223692
    Remove the 2 oil pipe unions, oil control valve filter RH, 3 gaskets and No. 2 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


16. DISCONNECT FUEL PIPE SUB-ASSEMBLY
  1. Remove the 2 bolts and disconnect the fuel pipe.


17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A223666
    Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A223665
    Remove the 3 gaskets.


18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A223669
    Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A223668
    Remove the 3 gaskets.


19. REMOVE TIMING CHAIN COVER PLATE

  1. A224737
    Remove the 4 bolts, timing chain cover plate and gasket.


20. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A072945E01
    Turn the crankshaft pulley and align the notch with the "0" timing mark of the timing chain cover.

  1. A224754E01
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
    Text in Illustration 
    *A
    for Bank 2
    *B
    for Bank 1
    *1
    Paint Mark

    HINT:
    If the marks are not aligned, turn the crankshaft again to align the marks.

  1. Place paint marks on the timing marks and sprockets of each camshaft timing gear and on the links of the No. 1 chain.

    HINT:
    Be sure to place the paint marks on 2 links of the chain and on the sprockets of the camshaft timing gears at the locations of the timing marks of the camshaft timing gears.


21. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A226510E01
    Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain.

    HINT:
    This prevents the valves and pistons from interfering with each other.

  1. A226547E01
    Align the hole in the lever of the tensioner with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of 1.27 mm (0.0500 in.) into the hole.
    Text in Illustration 
    *1
    Lever Hole
    *2
    Tensioner Hole

  1. Turn the crankshaft clockwise and align the notch with the "0" timing mark of the timing chain cover.

  1. A224739
    Remove the 2 bolts and chain tensioner.

    NOTICE:
    Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover.


22. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)

  1. A226507E01
    Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain between the banks.

    CAUTION:
    As the camshafts turn suddenly, do not touch the camshafts or camshaft timing gears.

    NOTICE:
    When turning the crankshaft, engine oil may spray out of the oil holes.

  1. A226508E05
    Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain can be removed easily.
    Text in Illustration 
    *a
    5° to 10°

    NOTICE:
    When turning the crankshaft, engine oil may spray out of the oil holes.

  1. A224759
    Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

    CAUTION:
    As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.


23. REMOVE CAMSHAFT BEARING CAP (for Bank 1)

  1. A225726E01
    Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install bolts and washers for temporary installation of the camshaft housing in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Part Removal
    *b
    Installation of Bolts and Washers for Temporary Installation of Camshaft Housing

    NOTICE:
    1. Do not install the bearing caps when installing bolts and washers for temporary installation of the camshaft housing.
    2. Be sure to follow the numerical order when performing this procedure.
    3. Do not allow bolts and washers for temporary installation of the camshaft housing to contact the camshaft.
    4. Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.

    HINT:
    1. Arrange the removed parts so that they can be reinstalled in their original locations.
    2. Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)
    3. Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)


24. REMOVE NO. 2 CAMSHAFT

  1. A224761
    Remove the bolt of the No. 2 chain tensioner assembly.

  1. A224769
    Remove the No. 2 chain tensioner assembly while lifting up the No. 2 camshaft.

  1. A224763
    While lifting up the No. 2 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


25. REMOVE CAMSHAFT
  1. Lift up the rear of the camshaft so that it is at an angle.

  1. A224767
    Remove the chain from the camshaft timing gear and pull out the camshaft and No. 2 chain towards the rear of the vehicle to remove them.

    NOTICE:
    Do not drop the chain into the gap between the engine and cover.

  1. A224765
    Suspend the chain with a string or equivalent.


26. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)
  1. Turn the crankshaft counterclockwise and align the notch with the "0" timing mark of the timing chain cover.

  1. A224760
    Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.

    CAUTION:
    As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.


27. REMOVE CAMSHAFT BEARING CAP (for Bank 2)

  1. A225727E01
    Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install bolts and washers for temporary installation of the camshaft housing in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *1
    Bolt
    *2
    Washer
    *a
    Part Removal
    *b
    Installation of Bolts and Washers for Temporary Installation of Camshaft Housing

    NOTICE:
    1. Do not install the bearing caps when installing bolts and washers for temporary installation of the camshaft housing.
    2. Be sure to follow the numerical order when performing this procedure.
    3. Do not allow bolts and washers for temporary installation of the camshaft housing to contact the camshaft.
    4. Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.

    HINT:
    1. Arrange the removed parts so that they can be reinstalled in their original locations.
    2. Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)
    3. Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)


28. REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

  1. A224762
    Remove the bolt of the No. 3 chain tensioner assembly.

  1. A224770
    Remove the No. 3 chain tensioner assembly while lifting up the No. 4 camshaft.

  1. A224764
    While lifting up the No. 4 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.


29. REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

  1. A224768
    Lift up the rear of the camshaft so that it is at an angle.

  1. Remove the chain from the camshaft timing gear and pull out the No. 3 camshaft and No. 2 chain towards the rear of the vehicle to remove them.

    NOTICE:
    Do not drop the chain into the gap between the engine and cover.

  1. A224766
    Suspend the chain with a string or equivalent.


30. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.

  1. A227959E01
    Remove the flange bolt and camshaft timing gear assembly.
    Text in Illustration 
    *1
    Do not remove
    *2
    Straight Pin
    *3
    Flange Bolt

    NOTICE:
    1. Do not remove the other 3 bolts.
    2. If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.


31. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.

  1. A227960E01
    Remove the flange bolt and camshaft timing exhaust gear assembly.
    Text in Illustration 
    *1
    Do not remove
    *2
    Straight Pin
    *3
    Flange Bolt

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.

← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →