2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and under cover.


4. REMOVE UPPER RADIATOR SUPPORT SEAL

  1. B180889
    Remove the 7 clips and radiator support seal.


5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


    A174296E01

  1. Tighten the radiator drain cock plug by hand.


6. REMOVE V-BANK COVER

  1. A174355
    Remove the 2 cap nuts and V-bank cover.


7. REMOVE NO. 2 AIR CLEANER HOSE

  1. A178932
    Loosen the 2 hose clamps and remove the air cleaner hose.


8. REMOVE AIR CLEANER ASSEMBLY

  1. A151812
    Disconnect the No. 2 ventilation hose.

  1. Detach the hose clamp.

  1. A185261
    Disconnect the vacuum hose.

  1. Disconnect the MAF meter connector.

  1. Using a clip remover, detach the 2 wire harness clamps.

  1. A151770
    Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner assembly.


9. REMOVE INTAKE AIR SURGE TANK

  1. A151856
    Disconnect the throttle body connector.

  1. Disconnect the No. 4 water by-pass hose.

  1. Disconnect the No. 5 water by-pass hose.

  1. A178934
    Disconnect the purge line hose.

  1. Disconnect the purge VSV connector.

  1. Disconnect the No. 1 ventilation hose.

  1. A185262
    Disconnect the vacuum switching valve (for ACIS) connector.

  1. Using a clip remover, detach the 2 wire harness clamps.

  1. A151767
    Remove the 2 bolts and throttle body bracket.

  1. A178935
    Using a clip remover, detach the wire harness clamp.

  1. A178936
    Remove the bolt and bracket from the No. 1 surge tank stay.

  1. Remove the bolt and oil baffle plate.

  1. A178937
    Remove the 2 bolts and No. 1 surge tank stay.

  1. A178939
    for Manual Transmission:

    1. Remove the nut.

  1. A178938
    Remove the 2 bolts and No. 2 surge tank stay.

  1. A178940E01
    Remove the 2 nuts.

  1. Using an 8 mm hexagon wrench, remove the 4 bolts. Then remove the intake air surge tank and gasket.


10. REMOVE IGNITION COIL ASSEMBLY
  1. Disconnect the 6 connectors.

  1. Remove the 6 bolts and ignition coils.


11. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

  1. A072943E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


12. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

  1. A072944E01
    Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


13. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A076530E01
    Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. G038065E10
    Check that the timing marks of the camshaft timing gears and sprockets are aligned with the timing marks of the bearing caps as shown in the illustration.
    If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.


14. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from TDC first.

  1. A076506E01
    Remove the 4 bolts, timing chain cover plate and gasket.

  1. A072958E03
    While turning the stopper plate of the tensioner clockwise, push in the plunger of the chain tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ3.5 mm (0.138 in.) into the holes on the stopper plate and tensioner to fix the stopper plate in place.

  1. Remove the 2 bolts and chain tensioner.


15. REMOVE NO. 2 CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. G038067E04
    While raising the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.

  1. G038068E01
    Hold the hexagonal portion of the No. 2 camshaft with a wrench, and remove the camshaft timing sprocket set bolt.

    NOTICE:
    Be careful not to damage the cylinder head and valve lifter with the wrench.

  1. Separate the camshaft timing sprocket from the No. 2 camshaft.

  1. G038069E01
    Rotate the camshaft counterclockwise using a wrench so that the cam lobes of the No. 1 cylinder face upward as shown in the illustration.

  1. A076510E15
    Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration.

  1. Remove the 4 bearing caps and No. 2 camshaft.


16. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

  1. G038070E01
    Remove the No. 2 chain tensioner bolt, and then remove the No. 2 chain tensioner and camshaft timing sprocket.


17. REMOVE NO. 1 CAMSHAFT

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. G038072E01
    Hold the hexagonal portion of the No. 1 camshaft with a wrench, and loosen the camshaft timing gear set bolt.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.

  1. G038071E01
    Slide the camshaft timing gear and separate the No. 1 chain from the camshaft timing gear.

  1. G038073E01
    Rotate the No. 1 camshaft counterclockwise using a wrench so that the cam lobes of the No. 1 cylinder face downward as shown in the illustration.

  1. A076515E01
    Using several steps, loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 4 bearing caps.

  1. G038074E01
    Remove the camshaft timing gear set bolt with the No. 1 camshaft lifted up, and then remove the No. 1 camshaft and camshaft timing gear with the No. 2 chain.

  1. A076517E01
    Tie the No. 1 chain with a string as shown in the illustration.

    NOTICE:
    Be careful not to drop anything inside the timing chain cover.


18. REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. G038075E01
    While pushing down the No. 3 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.

  1. G038076E01
    Hold the hexagonal portion of the No. 4 camshaft with a wrench, and remove the camshaft timing sprocket set bolt.

    NOTICE:
    Be careful not to damage the cylinder head and valve lifter with the wrench.

  1. Separate the camshaft timing sprocket from the No. 4 camshaft.

  1. A076482E01
    Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration.

  1. Remove the 4 bearing caps and No. 4 camshaft.


19. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

  1. G038077E01
    Remove the No. 3 chain tensioner bolt, and then remove the No. 3 chain tensioner and camshaft timing sprocket.


20. REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

NOTICE:
As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, the following steps should be carried out.

  1. A076484E01
    Release the chain tension between the camshaft timing gear (LH bank) and crankshaft timing gear by turning the crankshaft pulley counterclockwise slightly.

  1. G038400E01
    Hold the hexagonal portion of the No. 3 camshaft with a wrench, and loosen the camshaft timing gear set bolt.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.

  1. G038401E01
    Slide the camshaft timing gear and separate the No. 1 chain from the camshaft timing gear.

  1. A076487E02
    Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration.

  1. Remove the 4 bearing caps.

  1. G038402E01
    Remove the camshaft timing gear set bolt with the No. 3 camshaft lifted up, and then remove the No. 3 camshaft and camshaft timing gear with the No. 2 chain.

  1. A076489E01
    Tie the No. 1 chain with a string as shown in the illustration.

    NOTICE:
    Be careful not to drop anything inside the timing chain cover.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →