2011-2013 Land Cruiser · Service Manual Power Source / Network

U0130 Lost Communication with Steering Effort Control Module

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Area
U0130
There is no communication from the steering control ECU.
  1. Power source circuit of steering control ECU
  2. Steering control ECU CAN branch wire or connector
  3. Steering control ECU
  1. For vehicles with a variable gear ratio steering system.

WIRING DIAGRAM

C172536E06

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3. CHECK FOR OPEN IN CAN BUS WIRE (STEERING CONTROL ECU CAN BRANCH WIRE)

  1. C238625E03
    Disconnect the E79 steering control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E79-9 (CANH) - E79-20 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Steering Control ECU)



NG
REPAIR OR REPLACE STEERING CONTROL ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


4. CHECK HARNESS AND CONNECTOR (STEERING CONTROL ECU - BATTERY AND BODY GROUND)

  1. C238626E04
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the E77 and E78 steering control ECU connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E77-10 (+BI) - Body ground
    Always
    11 to 14 V
    E77-8 (PIG) - Body ground
    Always
    11 to 14 V
    E77-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E77-7 (PGND) - Body ground
    Always
    Below 1 Ω
    E78-8 (PGD2) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Rear view of wire harness connector
(to Steering Control ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEERING CONTROL ECU (Click here)


← U0130 Lost Communication with Steering Effort Control Module (Sep 2011 – Dec 2011)U0131 Lost Communication with Power Steering Control Module (from Jan 2012) →