2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LHD and RHD.
  2. The procedures listed below are for the LHD.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

B184533E01
  1. Connect the belt anchor.

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.


2. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B184532E01
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

    HINT:
    The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, connect it when installing the rear No. 1 seat inner belt LH.


3. INSTALL REAR SEAT UNDER TRAY COVER LH

B181181
  1. Attach the 4 claws to install the cover.

  1. Install the 2 screws.


4. INSTALL REAR SEAT CUSHION COVER RH

B181231
  1. Attach the 2 claws to install the cover.

  1. Install the 4 screws.


5. INSTALL REAR UNDER SIDE COVER LH

B181230
  1. Attach the 2 claws and 2 clips to install the cover.

  1. Install the 5 screws.

  1. B181229
    Attach the 10 claws.


6. INSTALL REAR SEATBACK STAY COVER LH

B181226
  1. Attach the 2 claws to install the cover.

  1. Install the screw.


7. INSTALL SEAT BELT ANCHOR COVER CAP

  1. B181228
    Install the anchor cover cap with the screw.

  1. B184029
    Attach the claw to close the cap.


8. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

B184017
  1. Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


9. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

  1. B181176
    Attach the cable clamp to connect the cable.

  1. B184045
    Install the hinge with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. w/ Rear Seat Side Airbag:
    Attach the wire harness clamp.

  1. w/ Seat Heater System:
    Attach the wire harness clamp.


10. INSTALL REAR NO. 2 SEAT PROTECTOR
  1. Install the wire harness, and attach 2 claws to close the protector.

  1. B182595
    Attach the claw to install the protector to the seat hinge.

  1. Install the clip.

  1. B184016
    w/ Rear Seat Side Airbag:
    Attach the claw to install the wire harness connector.

  1. w/ Seat Heater System:
    Attach the claw to install the wire harness connector.


11. INSTALL REAR NO. 2 SEAT LEG SIDE COVER

  1. B184044
    Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

  1. B181224
    Attach the 4 claws to install the seat leg side cover.

  1. Install the 4 screws.


12. INSTALL UPPER SEAT TRACK RAIL COVER RH

B184041
  1. Attach the 2 claws to install the cover.


13. INSTALL UPPER SEAT TRACK RAIL COVER LH

B184028
  1. Attach the 2 claws to install the cover.


14. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

B184015
  1. Attach the 4 claws to install the cover.

  1. Install the 2 screws.


15. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

B184027E01
  1. Attach the 3 claws in the order shown in the illustration to install the cover.

  1. Install the 2 screws.


16. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

B184013
  1. Install the release handle with the screw.


17. INSTALL SEAT ADJUSTER BOLT COVER

B184012
  1. Attach the 2 claws to install the cover.


18. INSTALL REAR NO. 1 SEAT ASSEMBLY LH
  1. Install the rear No. 1 seat assembly (Click here).

← REMOVAL (from Jan 2012)INSTALLATION (from Jan 2012) →