2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH
  1. Remove the rear No. 1 seat assembly (Click here).


2. REMOVE SEAT ADJUSTER BOLT COVER

B184012
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

B184013
  1. Remove the screw and release handle.


4. REMOVE REAR NO. 1 SEAT RECLINING COVER LH

B184014E01
  1. Remove the 2 screws.

  1. Detach the 3 claws in the order shown in the illustration, and then remove the cover.


5. REMOVE REAR NO. 1 SEAT RECLINING COVER RH

B184015
  1. Remove the 2 screws.

  1. Detach the 4 claws and remove the cover.


6. REMOVE UPPER SEAT TRACK RAIL COVER LH

B181222
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


7. REMOVE UPPER SEAT TRACK RAIL COVER RH

B184035
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


8. REMOVE REAR NO. 2 SEAT LEG SIDE COVER

  1. B181224
    Remove the 4 screws and detach the 4 claws.

  1. B184044
    Remove the bolt that is securing the fold seat stopper band and remove the seat leg side cover together with the fold seat stopper band.


9. REMOVE REAR NO. 2 SEAT PROTECTOR

  1. B184016
    w/ Rear Seat Side Airbag:
    Detach the claw and remove the wire harness connector.

  1. w/ Seat Heater System:
    Detach the claw and remove the wire harness connector.

  1. B182595
    Using a clip remover, remove the clip.

  1. Detach the claw and remove the seat protector from the seat hinge.

  1. Detach the 2 claws, open the protector and remove wire harness.


10. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

  1. B184045
    w/ Rear Seat Side Airbag:
    Detach the wire harness clamp.

  1. w/ Seat Heater System:
    Detach the wire harness clamp.

  1. Remove the 2 nuts and hinge.

  1. B181176
    Detach the cable clamp and disconnect the cable.


11. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

B184017
  1. Remove the 2 nuts and hinge.


12. REMOVE SEAT BELT ANCHOR COVER CAP

  1. B181227
    Detach the claw and open the cap.

  1. B181228
    Remove the screw and anchor cover cap.


13. REMOVE REAR SEATBACK STAY COVER LH

B181226
  1. Remove the screw.

  1. Detach the 2 claws and remove the cover.


14. REMOVE REAR UNDER SIDE COVER LH

  1. B181229
    Detach the 10 claws.

  1. B181230
    Remove the 5 screws.

  1. Detach the 2 clips and 2 claws, and remove the cover.


15. REMOVE REAR SEAT CUSHION COVER RH

B181231
  1. Remove the 4 screws.

  1. Detach the 2 claws and remove the cover.


16. REMOVE REAR SEAT UNDER TRAY LH COVER

B181181
  1. Remove the 2 screws.

  1. Detach the 4 claws and remove the cover.


17. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

B184531E01
  1. Remove the bolt and belt.

    HINT:
    The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, it becomes disconnected when the bolt is removed.


18. DISCONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

B184533E02
  1. Disconnect the belt anchor.

← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →