2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

  1. Connect the cable to the clamps shown in the illustration to install the cable.

    B182555


2. INSTALL FUEL FILLER OPENING LID LOCK RETAINER

  1. B181055
    Install the lock retainer and turn it clockwise as shown in the illustration.

  1. B181056
    Install the cable and turn it clockwise as shown in the illustration.


3. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

  1. B181065
    Connect the fuel lid lock control cable to the fuel lid lock open lever.

  1. Attach the 2 claws to install the fuel lid lock open lever.


4. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

B182645

HINT:
When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

  1. w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. w/o Rear Air Conditioning System:
      Connect the rear seat lock control lever cable.

    2. w/ Rear Air Conditioning System:
      Connect the thermistor connector and rear seat lock control lever cable.

    3. Attach the 16 clips and 2 claws to install the quarter trim panel.

    4. Install the clip and bolt.

      Torque:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }


      B186890

  1. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

    1. Attach the 16 clips and 2 claws to install the quarter trim panel.

    2. Install the clip.

      B190220

  1. w/ Tonneau Cover:

    1. Attach the 16 clips and 2 claws to install the quarter trim panel.

    2. Install the screw and clip.

      B186438

  1. B181693
    w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. Install the rear No. 2 seat belt anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. B181692
      Attach the 3 claws to install the cover.

  1. B181690
    Install the rear No. 1 seat belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B181688
    Attach the 3 claws to install the cover.


5. INSTALL NO. 1 REAR SEAT COVER BEZEL (w/ Rear No. 2 Seat)

HINT:
Use the same procedures described for the rear No. 2 seat cover bezel.


6. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

B186439

HINT:
Use the same procedure to install the tonneau cover holder cap on the other side.

  1. Attach the 2 claws to install the tonneau cover holder cap.


7. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

B181672
  1. Attach the 6 clips to install the support plate.


8. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


9. INSTALL REAR STEP COVER

B181673

HINT:
Use the same procedure to install the step cover on the other side.

  1. Attach the 2 claws to install the step cover.


10. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


11. INSTALL COWL SIDE TRIM BOARD RH

B180022
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the cap nut.


12. INSTALL INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

B182551
  1. Attach the 6 claws to install the instrument side panel.


13. INSTALL INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

B186358
  1. Connect the connector.

  1. Attach the 6 claws to install the instrument side panel.


14. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.


15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSTALLATION (Sep 2011 – Dec 2011)PARTS LOCATION (from Sep 2011) →