2011-2013 Land Cruiser · Service Manual Suspension

REMOVAL

Removal / installation · Vehicles built from Sep 2011


1. TABLE OF BOLT, SCREW AND NUT

HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.


B292999E01

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

  1. E155426E02
    Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 7 claws and remove the panel cushion.


4. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

  1. B181910
    Remove the clip.

  1. Remove the screw.

  1. Detach the 8 claws.

  1. Remove the panel pad and disconnect the connectors and 2 clamps.


5. REMOVE NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION

  1. B180004E01
    Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 7 claws and remove the panel cushion.


6. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH

  1. B180005
    Remove the clip.

  1. Remove the screw.

  1. Detach the 7 claws and remove the panel.


7. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B180006
    Detach the 7 claws.

  1. Disconnect the connectors and remove the panel.


8. REMOVE INSTRUMENT SIDE PANEL LH

E154740E06
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the instrument side panel.


9. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

E154744E04
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.


10. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

    B291251E01

    Text in Illustration 
    *A
    w/ Entry and Start System
    *B
    w/o Entry and Start System
    *1
    Protective Tape
    -
    -


11. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B180655
  1. Remove the 2 screws.

  1. Detach the 3 claws.

  1. Disconnect the connectors and remove the No. 1 instrument panel under cover.


12. REMOVE FRONT DOOR SCUFF PLATE LH

13. REMOVE COWL SIDE TRIM BOARD LH

B181911
  1. Remove the cap nut.

  1. Detach the 2 clips and remove the cowl side trim board.


14. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

B180295E02
  1. Using a screwdriver, detach the 2 claws and open the hole cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. w/ Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 16 claws.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 9 claws.

      B291250

  1. B180296
    for Automatic Air Conditioning System:

    1. Detach the 2 claws and remove the room temperature sensor.

  1. B181942
    Detach the 2 claws and disconnect the 2 control cables.

  1. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.


15. REMOVE NO. 1 SWITCH HOLE BASE

B180298
  1. Detach the 4 claws.

  1. Disconnect the connectors and remove the No. 1 switch hole cover.


16. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

  1. B189602E01
    Remove the 5 bolts and driver side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


17. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

B180299
  1. Detach the 2 claws and disconnect the DLC3.

  1. Remove the 5 bolts and lower instrument panel.


18. REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

B181912E02
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the instrument side panel.


19. REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

B180301E02
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws.

  1. Disconnect the connector and remove the instrument side panel.


20. REMOVE FRONT DOOR SCUFF PLATE RH

21. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B180656
  1. Detach the 4 claws and remove the No. 2 instrument panel under cover.


22. REMOVE COWL SIDE TRIM BOARD RH

B180022
  1. Remove the cap nut.

  1. Detach the 2 clips and remove the cowl side trim board.


23. REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

  1. B189606E01
    Remove the 4 bolts.

  1. Detach the 4 claws and remove the front passenger side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


24. REMOVE LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

B180302
  1. Remove the 2 bolts.

  1. Detach the 4 claws and remove the lower instrument panel.


25. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B180303E02
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the No. 3 instrument cluster finish panel garnish.


26. REMOVE INSTRUMENT PANEL BOX DOOR KNOB

B182302
  1. Using a moulding remover, detach the 2 claws and remove the instrument panel box door knob.


27. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

B180304
  1. Remove the 4 bolts.

  1. Detach the 3 claws.

  1. Disconnect the connector and remove the lower No. 2 instrument panel finish panel.


28. REMOVE STEERING CONTROL ECU WITH JUNCTION BLOCK (for LHD)

  1. C172815E01
    Vehicle rear side:

    1. Disconnect the 7 connectors.

    2. Detach the 2 clamps.

    3. Remove the bolt and 2 nuts.

  1. Vehicle front side:

    1. Disconnect the 5 connectors.

  1. Remove the steering control ECU with junction block from the vehicle.


29. REMOVE STEERING CONTROL ECU WITH JUNCTION BLOCK (for RHD)

  1. C172817E01
    Vehicle rear side:

    1. Disconnect the 2 connectors.

    2. Remove the bolt and 2 nuts.

  1. Vehicle front side:

    1. Disconnect the connector.

  1. Remove the steering control ECU with junction block from the vehicle.


30. REMOVE ACCELERATION SENSOR (for Driver Side)

  1. C172824
    Disconnect the connector.

  1. Remove the bolt and sensor.

    HINT:
    Use the same procedures for LHD and RHD vehicles.


31. REMOVE ACCELERATION SENSOR (for Front Passenger Side)

  1. C172825
    Disconnect the connector.

  1. Remove the bolt and sensor.

    HINT:
    Use the same procedures for LHD and RHD vehicles.

← COMPONENTS (from Sep 2011)INSPECTION (from Sep 2011) →