2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar support)

  1. B180724
    Install the lumbar support adjuster with the 2 screws.

  1. Connect the lumbar support adjuster connector.

  1. B293541E01
    Attach the 4 hooks to install the seatback spring.

  1. Connect the active headrest cable with the cable clamp.

  1. Install the 4 springs.


2. INSTALL SEATBACK COVER WITH PAD
  1. Set the seatback cover with pad in place.

  1. w/ Seatback Board:

    1. B180716
      w/ Front Seat Side Airbag:
      Install the seatback cover bracket to the seat frame with the nut.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

      CAUTION:
      After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.

    2. B191295E01
      Attach the 9 hooks.

    3. Using hog ring pliers, install new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.

  1. w/o Seatback Board:

    1. B180768
      Attach the 4 claws to install the 2 headrest supports.

    2. B180716
      w/ Front Seat Side Airbag:
      Install the seatback cover bracket to the seat frame with the nut.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

      CAUTION:
      After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.

    3. B185566
      Close the 2 fasteners.

    4. B180766
      Using hog ring pliers, install new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.


3. INSTALL FRONT SEAT HEADREST SUPPORT (w/ Active Headrest)

B180712
  1. Attach the 4 claws to install the 2 front seat headrest supports.


4. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)

B182646
  1. Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.

  1. Install the 2 screws.


5. INSTALL FRONT INNER SEAT CUSHION SHIELD LH

B180761
  1. Attach the claw and clip to install the front inner seat cushion shield LH.

  1. Install the screw.


6. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

B189679E01
  1. Install the front seat inner belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Connect the connectors and attach the clamps.


7. INSTALL FRONT SEAT CUSHION SHIELD LH
  1. w/ Lumbar Support:
    Connect the lumbar switch connector.

  1. for 4 Way Seat Type:

    1. B180780E01
      Attach the 3 claws in the order shown in the illustration to install the front seat cushion shield LH.

    2. Install the 2 screws.

  1. for 8 Way Seat Type:

    1. B180786E01
      Attach the 3 claws in the order shown in the illustration to install the front seat cushion shield LH.

    2. Install the 3 screws.

  1. B180757
    w/ Seatback Board:
    Connect the 2 rubber bands to the 2 hooks.

  1. B180756
    w/o Seatback Board:
    Connect the rubber band to the 2 hooks.


8. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

B185571
  1. Attach the claw to install the reclining adjuster release handle LH.


9. INSTALL VERTICAL SEAT ADJUSTER KNOB (for 8 Way Seat Type)

B180781
  1. Install the snap ring to the vertical seat adjuster knob.

  1. Install the vertical seat adjuster knob.


10. INSTALL VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type)

B180753
  1. Install the vertical adjusting handle with the 2 screws.


11. INSTALL VERTICAL ADJUSTER COVER LH (for 8 Way Seat Type)

B180752
  1. Attach the 2 claws to install the vertical adjuster cover LH.


12. INSTALL FRONT SEAT ASSEMBLY LH
  1. Install the front seat assembly (Click here).

← INSPECTION (from Sep 2011)INSTALLATION (from Jan 2012) →