INSTALLATION
Removal / installation · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
| 1.
INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar support) |
 |
- Install the lumbar support adjuster with the 2 screws.
Connect the lumbar support adjuster connector.
- Attach the 4 hooks to install the seatback spring.
Connect the active headrest cable with the cable clamp.
Install the 4 springs.
| 2.
INSTALL SEATBACK COVER WITH PAD
|
 |
Set the seatback cover with pad in place.
w/ Seatback Board:
- w/ Front Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the nut.
-
Torque:
- 5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
- CAUTION:
- After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.
- Attach the 9 hooks.
Using hog ring pliers, install new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
w/o Seatback Board:
- Attach the 4 claws to install the 2 headrest supports.
- w/ Front Seat Side Airbag:
Install the seatback cover bracket to the seat frame with the nut.
-
Torque:
- 5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
- CAUTION:
- After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.
- Close the 2 fasteners.
- Using hog ring pliers, install new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
| 3.
INSTALL FRONT SEAT HEADREST SUPPORT (w/ Active Headrest)
|
 |
Attach the 4 claws to install the 2 front seat headrest supports.
| 4.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)
|
 |
Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.
Install the 2 screws.
| 5.
INSTALL FRONT INNER SEAT CUSHION SHIELD LH
|
 |
Attach the claw and clip to install the front inner seat cushion shield LH.
Install the screw.
| 6.
INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
|
 |
Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect the connectors and attach the clamps.
| 7.
INSTALL FRONT SEAT CUSHION SHIELD LH
|
 |
w/ Lumbar Support:
Connect the lumbar switch connector.
for 4 Way Seat Type:
- Attach the 3 claws in the order shown in the illustration to install the front seat cushion shield LH.
Install the 2 screws.
for 8 Way Seat Type:
- Attach the 3 claws in the order shown in the illustration to install the front seat cushion shield LH.
Install the 3 screws.
- w/ Seatback Board:
Connect the 2 rubber bands to the 2 hooks.
- w/o Seatback Board:
Connect the rubber band to the 2 hooks.
| 8.
INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
|
 |
Attach the claw to install the reclining adjuster release handle LH.
| 9.
INSTALL VERTICAL SEAT ADJUSTER KNOB (for 8 Way Seat Type)
|
 |
Install the snap ring to the vertical seat adjuster knob.
Install the vertical seat adjuster knob.
| 10.
INSTALL VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type)
|
 |
Install the vertical adjusting handle with the 2 screws.
| 11.
INSTALL VERTICAL ADJUSTER COVER LH (for 8 Way Seat Type)
|
 |
Attach the 2 claws to install the vertical adjuster cover LH.
| 12.
INSTALL FRONT SEAT ASSEMBLY LH |
 |
Install the front seat assembly (Click here).