INSTALLATION
Removal / installation · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| 1. INSTALL STEERING CONTROL ECU |
![]() ![]() |
Install the steering control ECU to the junction block with the 2 bolts.
- Torque:
- for bolt A:
- 5.0 N*m{ 56 kgf*cm , 49 in.*lbf }
- for bolt B:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 2. INSTALL STEERING CONTROL ECU WITH JUNCTION BLOCK |


Front side:
Connect the 3 connectors.
Rear side:
Install the steering control ECU with junction block with the bolt and 2 nuts.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Connect the 2 connectors.
| 3. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag) |
![]() ![]() |
Attach the 2 claws and connect the DLC3.
Install the lower instrument panel with the 5 bolts.
| 4. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag) |
Connect the connector.

- NOTICE:
- When handling the airbag connector, take care not to damage the airbag wire harness.
Install the driver side knee airbag with the 5 bolts.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
| 5. INSTALL NO. 1 SWITCH HOLE BASE |
![]() ![]() |
Connect the connectors.
Attach the 4 claws to install the No. 1 switch hole base.
| 6. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL |
Connect the connectors.
for Automatic Air Conditioning System:

Attach the 2 claws to install the room temperature sensor.
Attach the 2 claws to connect the 2 control cables.

w/ Driver Side Knee Airbag:
Attach the 16 claws to install the lower No. 1 instrument panel finish panel.
Install the 2 bolts.


w/o Driver Side Knee Airbag:
Attach the 9 claws to install the lower No. 1 instrument panel finish panel.
Install the 2 bolts.


Attach the 2 claws to close the hole cover.

| 7. INSTALL COWL SIDE TRIM BOARD RH |
![]() ![]() |
Attach the 2 clips to install the cowl side trim board.
Install the cap nut.
| 8. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover) |
![]() ![]() |
Connect the connectors.
Attach the 3 claws to install the No. 1 instrument panel under cover.
Install the 2 screws.
| 9. INSTALL FRONT DOOR SCUFF PLATE RH (w/ Sliding Roof) |
- HINT:
- Use the same procedures described for the LH side.
| 10. INSTALL FRONT DOOR SCUFF PLATE RH (w/o Sliding Roof) |
- HINT:
- Use the same procedures described for the LH side.
| 11. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.


Text in Illustration *A
w/ Entry and Start System
*B
w/o Entry and Start System
| 12. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() ![]() |
Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.
| 13. INSTALL INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch) |
![]() ![]() |
Connect the connector.
Attach the 6 claws to install the instrument side panel.
| 14. INSTALL INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch) |
![]() ![]() |
Attach the 6 claws to install the instrument side panel.
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).








