2011-2013 Land Cruiser · Service Manual Vehicle Exterior

TERMINALS OF ECU

System information · Vehicles built from Jan 2012


CHECK NO. 2 MAIN BODY ECU
B197193E02
  1. Disconnect the L50 and L51 No. 2 main body ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L50-14 (BECU) - Body ground
    R - Body ground
    BECU power supply
    Always
    11 to 14 V
    L50-13 (SIG) - Body ground
    G - Body ground
    SIG power supply
    Engine switch on (IG)
    11 to 14 V
    L50-13 (SIG) - Body ground
    G - Body ground
    SIG power supply
    Engine switch off
    Below 1 V
    L51-5 (B) - Body ground
    B - Body ground
    Lower tail gate lock motor RH power supply
    Always
    11 to 14 V
    L51-6 (B) - Body ground
    W - Body ground
    Lower tail gate lock motor LH power supply
    Always
    11 to 14 V
    L50-7 (GND) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    L51-7 (GND) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    L50-19 (BDSU) - Body ground
    V - Body ground
    Back door remote control signal circuit
    Back door remote control pulled (on)
    Below 1 Ω
    L50-19 (BDSU) - Body ground
    V - Body ground
    Back door remote control signal circuit
    Back door remote control free (off)
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the L50 and L51 No. 2 main body ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L51-3 (DC+) - L51-7 (GND)
    R - W-B
    Lower tail gate lock motor LH circuit
    Lower tail gate lock motor LH operating (close)
    11 to 14 V
    L51-3 (DC+) - L51-7 (GND)
    R - W-B
    Lower tail gate lock motor LH circuit
    Lower tail gate lock motor LH stopped
    Below 1 V
    L51-8 (DC-) - L51-7 (GND)
    B - W-B
    Lower tail gate lock motor LH circuit
    Lower tail gate lock motor LH operating (open)
    11 to 14 V
    L51-8 (DC-) - L51-7 (GND)
    B - W-B
    Lower tail gate lock motor LH circuit
    Lower tail gate lock motor LH stopped
    Below 1 V
    L51-2 (DC+) - L51-7 (GND)
    G - W-B
    Lower tail gate lock motor RH circuit
    Lower tail gate lock motor RH operating (close)
    11 to 14 V
    L51-2 (DC+) - L51-7 (GND)
    G - W-B
    Lower tail gate lock motor RH circuit
    Lower tail gate lock motor RH stopped
    Below 1 V
    L51-1 (DC-) - L51-7 (GND)
    W - W-B
    Lower tail gate lock motor RH circuit
    Lower tail gate lock motor RH operating (open)
    11 to 14 V
    L51-1 (DC-) - L51-7 (GND)
    W - W-B
    Lower tail gate lock motor RH circuit
    Lower tail gate lock motor RH stopped
    Below 1 V
    L51-9 (HAF) - L51-7 (GND)
    GR - W-B
    Half-latch switch LH signal circuit
    Lower tail gate open
    Below 1 V
    L51-9 (HAF) - L51-7 (GND)
    GR - W-B
    Half-latch switch LH signal circuit
    Lower tail gate closed
    Pulse generation
    (See waveform 1)
    L50-8 (HAF) - L51-7 (GND)
    B - W-B
    Half-latch switch RH signal circuit
    Lower tail gate open
    Below 1 V
    L50-8 (HAF) - L51-7 (GND)
    B - W-B
    Half-latch switch RH signal circuit
    Lower tail gate closed
    Pulse generation
    (See waveform 1)
    L51-4 (FUL) - L51-7 (GND)
    G - W-B
    Lower tail gate courtesy switch LH signal circuit
    Lower tail gate open
    Below 1 V
    L51-4 (FUL) - L51-7 (GND)
    G - W-B
    Lower tail gate courtesy switch LH signal circuit
    Lower tail gate closed
    Pulse generation
    (See waveform 1)
    L50-22 (FUL) - L51-7 (GND)
    Y - W-B
    Lower tail gate courtesy switch RH signal circuit
    Lower tail gate open
    Below 1 V
    L50-22 (FUL) - L51-7 (GND)
    Y - W-B
    Lower tail gate courtesy switch RH signal circuit
    Lower tail gate closed
    Pulse generation
    (See waveform 1)
    L51-10 (LMT) - L51-7 (GND)
    Y - W-B
    Close position switch LH signal circuit
    Lower tail gate closed
    Below 1 V
    L51-10 (LMT) - L51-7 (GND)
    Y - W-B
    Close position switch LH signal circuit
    Lower tail gate open
    Pulse generation
    (See waveform 2)
    L50-17 (LMT) - L51-7 (GND)
    L - W-B
    Close position switch RH signal circuit
    Lower tail gate closed
    Below 1 V
    L50-17 (LMT) - L51-7 (GND)
    L - W-B
    Close position switch RH signal circuit
    Lower tail gate open
    Pulse generation
    (See waveform 2)
    L50-15 (POL) - L51-7 (GND)
    L - W-B
    Pawl switch LH signal circuit
    Lower tail gate lock motor LH is operating
    Below 1 V
    L50-15 (POL) - L51-7 (GND)
    L - W-B
    Pawl switch LH signal circuit
    Lower tail gate open
    Pulse generation
    (See waveform 2)
    L50-16 (POL) - L51-7 (GND)
    R - W-B
    Pawl switch RH signal circuit
    Lower tail gate lock motor RH is operating
    Below 1 V
    L50-16 (POL) - L51-7 (GND)
    R - W-B
    Pawl switch RH signal circuit
    Lower tail gate open
    Pulse generation
    (See waveform 2)
    L50-19 (BDSU) - L51-7 (GND)
    V - W-B
    Back door remote control signal circuit
    Back door remote control pulled (on)
    Below 1 V
    L50-19 (BDSU) - L51-7 (GND)
    V - W-B
    Back door remote control signal circuit
    Back door remote control free (off)
    Pulse generation
    (See waveform 3)

  5. B197194E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal (Symbol)
    1. L51-9 (HAF) - L51-7 (GND)
    2. L50-8 (HAF) - L51-7 (GND)
    3. L51-4 (FUL) - L51-7 (GND)
    4. L50-22 (FUL) - L51-7 (GND)
    Tool Setting
    5 V/DIV., 5 ms/DIV
    Condition
    Lower tail gate closed

  6. B197195E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal (Symbol)
    1. L51-10 (LMT) - L51-7 (GND)
    2. L50-17 (LMT) - L51-7 (GND)
    3. L51-15 (POS) - L51-7 (GND)
    4. L50-16 (POS) - L51-7 (GND)
    Tool Setting
    5 V/DIV., 5 ms/DIV
    Condition
    Lower tail gate open

  7. B197194E01
    Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal (Symbol)
    L50-19 (BDSU) - L51-7 (GND)
    Tool Setting
    5 V/DIV., 5 ms/DIV
    Condition
    Back door remote control free (off)

← PROBLEM SYMPTOMS TABLE (from Jan 2012)DTC CHECK / CLEAR (from Jan 2012) →