INSTALLATION
Removal / installation · Vehicles built from Jan 2012
| 1. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install a new gasket and the front exhaust pipe to the exhaust manifold with the 2 nuts.
- Torque:
- 54 N*m{ 554 kgf*cm , 40 ft.*lbf }
| 2. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY |
Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with the 2 nuts.
- Torque:
- 54 N*m{ 554 kgf*cm , 40 ft.*lbf }
| 3. INSTALL CENTER EXHAUST PIPE ASSEMBLY |
Install 2 new gaskets to the center exhaust pipe.
Connect the center exhaust pipe to the 3 exhaust pipe supports.
Install the center exhaust pipe with the 4 bolts.
- Torque:
- 48 N*m{ 489 kgf*cm , 35 ft.*lbf }
| 4. INSTALL EXHAUST PIPE DAMPER |
Install the exhaust pipe damper and No. 4 exhaust pipe upper protector with the 2 bolts.
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
| 5. INSTALL TAILPIPE ASSEMBLY |
Install a new gasket to the center exhaust pipe.
Install the tailpipe to the 2 exhaust pipe supports.
Install a new clamp.

- Torque:
- 32 N*m{ 326 kgf*cm , 24 ft.*lbf }
Text in Illustration *a
Top
*b
LH Side
- HINT:
- Install the clamp within the angle range shown in the illustration.
| 6. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2) |
Temporarily install the sensor to the front No. 2 exhaust pipe by hand.
Using SST, tighten the heated oxygen sensor.

- SST
- 09224-00010
- Torque:
- without SST:
- 44 N*m{ 449 kgf*cm , 32 ft.*lbf }
- with SST:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
Text in Illustration *1
Fulcrum Length
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
- Make sure SST and the wrench are connected in a straight line.
- Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
Connect the heated oxygen sensor connector.
| 7. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2) |
Temporarily install the sensor to the front exhaust pipe by hand.
Using SST, tighten the heated oxygen sensor.

- SST
- 09224-00010
- Torque:
- without SST:
- 44 N*m{ 449 kgf*cm , 32 ft.*lbf }
- with SST:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
Text in Illustration *1
Fulcrum Length
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
- Make sure SST and the wrench are connected in a straight line.
- Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
Attach the clamp and connect the heated oxygen sensor connector.
| 8. INSTALL PROPELLER SHAFT HEAT INSULATOR |
Install the insulator with the 2 bolts.

- Torque:
- 16 N*m{ 160 kgf*cm , 12 ft.*lbf }
| 9. INSPECT FOR EXHAUST GAS LEAK |
