2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P144C Open in Secondary Air Injection System Heater Control Circuit

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

DESCRIPTION

The ECM operates the air pump heater relay (AI-PUMP HTR) which causes the air pump heater to operate.
DTC No.
DTC Detection Condition
Trouble Area
P144C
Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
  1. Open or short in air pump heater relay circuit
  2. Air pump heater relay (AI-PUMP HTR)
  3. ECM
P144D
Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
  1. Open or short in air pump heater relay circuit
  2. Air pump heater relay (AI-PUMP HTR)
  3. ECM

WIRING DIAGRAM

Refer to DTC P0412 (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT AIR PUMP HEATER RELAY (AI-PUMP HTR)
  1. Inspect the air pump heater relay (AI-PUMP HTR) (Click here).



NG
REPLACE AIR PUMP HEATER RELAY (AI-PUMP HTR)
OK


2. CHECK AIR PUMP HEATER RELAY (AI-PUMP HTR) (POWER SOURCE)
  1. Remove the air pump heater relay (AI-PUMP HTR) .

  1. A281075E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Air pump heater relay (AI-PUMP HTR) terminal 2 - Body ground
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    Air Pump Heater Relay (AI-PUMP HTR)

  1. Reinstall the air pump heater relay (AI-PUMP HTR) .



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER RELAY (AI-PUMP HTR))
  1. Remove the air pump heater relay (AI-PUMP HTR) .

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    Air pump heater relay (AI-PUMP HTR) terminal 1 - C46-60 (HAI1)
    Always
    Below 1 Ω
    Air pump heater relay (AI-PUMP HTR) terminal 1 or C46-60 (HAI1) - Body ground
    Always
    10 kΩ or higher
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    Air pump heater relay (AI-PUMP HTR) terminal 1 - C45-60 (HAI1)
    Always
    Below 1 Ω
    Air pump heater relay (AI-PUMP HTR) terminal 1 or C45-60 (HAI1) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the air pump heater relay (AI-PUMP HTR) .

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P1340 Camshaft Position Sensor "A" (Bank 1 Sensor 2) (+ P1342, P1343) (from Jan 2012)P1603 Engine Stall History (+ P1605) (from Jan 2012) →