2011-2013 Land Cruiser · Service Manual Vehicle Interior

Key Cannot be Registered

Circuit diagnosis · Vehicles built from Sep 2011

DESCRIPTION

A maximum of 5 master key codes and 3 sub key codes can be registered.

WIRING DIAGRAM

Refer to "System Diagram" (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.


1. CHECK REGISTRATION MODE
  1. Check that the system enters registration mode.

    OK:
    System enters registration mode



NG
Go to step 5
OK


2. CHECK SECURITY INDICATOR LIGHT OPERATION

  1. In registration mode, when the key is inserted in the ignition key cylinder, check that the security indicator light blinks in the normal pattern shown below.

    HINT:
    If the new key code registration fails, code 2-1 will be output through the security indicator light. Trying to reregister an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key codes exceeds the maximum limit, code 2-3 will be output through the security indicator light. The output details are shown below.

    B111593E31
    Result 
    Result
    Proceed to
    Code 2-1 or Code 2-3
    A
    Code 2-2
    B



B
REGISTRATION AS ANOTHER KEY
A


3. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Immobiliser / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Immobiliser 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Transponder S-code
    Number of registered sub-keys / min.: 0, max.: 3
    Number of registered sub-keys
    -
    Transponder M-code
    Number of registered master keys / min.: 0, max.: 5
    Number of registered master keys
    -
    Result 
    Result
    Proceed to
    None of the following
    A
    Registered master keys: 5, registered sub-keys: 0
    B
    Registered master keys: 0, registered sub-keys: 3
    C
    Registered master keys: 5, registered sub-keys: 3
    D



B
KEY REGISTRATION (SUB-KEY)

C
KEY REGISTRATION (MASTER KEY)

D
NOT KEY REGISTRATION
A


4. KEY REGISTRATION
  1. Refer to the table below to determine if additional keys can be registered.

    Number of Keys Registered (Master and Sub)
    Proceed to
    0
    New key ID registration (refer to the Service Bulletin)
    1 to 7
    Additional key ID registration (refer to the Service Bulletin)

  1. Check whether key registration.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END (KEY IS MALFUNCTIONING)

5. INSPECT UNLOCK WARNING SWITCH ASSEMBLY
  1. Inspect the unlock warning switch assembly (Click here).



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH)
  1. Disconnect the E94 unlock warning switch assembly connector.

  1. Disconnect the E96 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E94-1 (UN+) - E96-3 (KSW)
    Always
    Below 1 Ω
    E94-2 (UN-) - Body ground
    Always
    Below 1 Ω
    E94-1 (UN+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
  1. Inspect the front door courtesy light switch assembly (Click here).



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY)
  1. for LHD:

    1. Disconnect the K2 front door courtesy light switch assembly connector.

    2. Disconnect the E96 transponder key ECU assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K2-1 - E96-7 (CTY)
      Always
      Below 1 Ω
      K2-1 - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Disconnect the L1 front door courtesy light switch assembly connector.

    2. Disconnect the E96 transponder key ECU assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-1 - E96-7 (CTY)
      Always
      Below 1 Ω
      L1-1 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY


← Engine does not Start but Initial Combustion Occurs (from Jan 2012)Security Indicator Light Does not Blink (Sep 2011 – Dec 2011) →