2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Sep 2011

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE FRONT SEAT ASSEMBLY RH
(Click here)

2. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

B292994E01
  1. Put protective tape around the No. 2 instrument panel finish panel cushion.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and remove the No. 2 instrument panel finish panel cushion.


3. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

B292995
  1. Remove the clip and screw.

  1. Detach the 8 claws.

  1. Disconnect the connectors, detach the 2 clamps and remove the lower instrument panel pad sub-assembly.


4. REMOVE NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION

B180004E02
  1. Put protective tape around the No. 1 instrument panel finish panel cushion.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and remove the No. 1 instrument panel finish panel cushion.


5. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH

B180005
  1. Remove the clip and screw.

  1. Detach the 7 claws and remove the lower instrument panel pad sub-assembly.


6. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

B292996
  1. Detach the 7 claws.

  1. Disconnect the connectors and remove the lower center instrument cluster finish panel sub-assembly.


7. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH
  1. Put protective tape around the upper No. 2 console panel garnish.

  1. Using a screwdriver, detach the 8 claws and remove the upper No. 2 console panel garnish.

    HINT:
    Tape the screwdriver tip before use.


    B291236E01
    Text in Illustration 
    *A
    for Separate Seat Type
    *B
    for Bench Seat Type
    *1
    Protective Tape
    -
    -


8. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH

B291238E01
  1. Put protective tape around the upper No. 1 console panel garnish.

  1. Using a screwdriver, detach the 8 claws and remove the upper No. 1 console panel garnish.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


9. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. Put protective tape around the rear upper console panel sub-assembly.

  1. Using a moulding remover, detach the 12 claws and remove the rear upper console panel sub-assembly.

    B291240E01

    Text in Illustration 
    *1
    Protective Tape
    -
    -


10. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

B291232
  1. Twist the shift lever knob sub-assembly in the direction indicated by the arrow and remove it.


11. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

B291234E01
  1. Put protective tape around the upper console panel sub-assembly.

  1. Using a moulding remover, detach the 8 claws and remove the upper console panel sub-assembly.


12. REMOVE LOWER CONSOLE BOX

B291242
  1. Remove the 2 screws and 4 bolts.

  1. Detach the 2 claws and remove the lower console box.

← COMPONENTS (from Sep 2011)DISASSEMBLY (from Sep 2011) →