Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR
BM2660E _01 Vehicle Exterior _054376 BODY WELD POINT _0264583 FRONT BODY PILLAR F

BODY WELD POINT  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K127143

With the cowl top side panel removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

REMOVAL POINT
1.

Reuse *a, as the area of the outer panel that is cut and joined is to the rear of the supplied part cut position.

2.

Remove the side panel gusset at the same time.


K127177C01
1.594,2.313 1.073,1.167 false 3.833,4.948 2.813,4.219 false 0.979,0.979 1.323,1.167 0.344,0.188 10 false *1 6.594,8.51 6.906,8.667 0.313,0.156 10 false *b 5.646,5.552 6.375,5.76 0.729,0.208 10 false 50 (1.97) 5.792,6.875 6.521,7.083 0.729,0.208 10 false 55 (2.17) 2.833,5.688 3.563,5.896 0.729,0.208 10 false 75 (2.95) 2.333,6.031 3.063,6.24 0.729,0.208 10 false 60 (2.36) 4.354,1.688 5.052,1.969 0.698,0.281 10 false 350 (13.78) 4.563,1.042 5.146,1.385 0.583,0.344 10 false 70 (2.76) 3.885,4.896 4.073,5.104 0.188,0.208 10 false *a
*1 Side Panel Gusset - -
*b mm (in.) - -


K127178


INSTALLATION


Symbol Meaning
K108818

Remove Weld Points
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld
K108834

Body Sealer

INSTALLATION POINT
1.

Before temporarily installing the new parts, weld the rocker outer panel, front body pillar lower reinforce, side inner panel, front body outer pillar and side panel gusset with the standard number of welding points.

2.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

3.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram)

4.

Before installing a new part, apply body sealer.

HINT:

Apply sealer in an even, continuous bead.


5.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

6.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

7.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K127179C01
6.583,8.552 6.896,8.708 0.313,0.156 10 false *a 2.51,5.333 4.042,5.531 1.531,0.198 10 false 200 (7.87) 6.281,5.688 6.958,6.063 0.677,0.375 10 false 195 (7.68) 2.26,0.927 2.844,1.135 0.583,0.208 10 false 60 (2.36) 2.865,0.917 3.448,1.125 0.583,0.208 10 false 75 (2.95) 4.885,0.833 5.469,1.042 0.583,0.208 10 false 30 (1.18) 4.198,1.177 4.781,1.385 0.583,0.208 10 false 30 (1.18)
*a mm (in.) - -


K127180C01
1.635,7.604 1.167,8.26 false 5.104,5.802 4.635,6.458 false 1.823,4.719 1.531,5.115 false 2.74,3.073 1.896,2.479 false 3.219,0.573 2.302,1.042 false 3.229,0.406 3.542,0.563 0.313,0.156 10 false *1 2.802,3.01 3.115,3.167 0.313,0.156 10 false *2 1.781,4.5 2.094,4.656 0.313,0.156 10 false *3 1.073,8.281 1.385,8.438 0.313,0.156 10 false *4 4.531,6.49 4.844,6.646 0.313,0.156 10 false *5
*1 Front Body Outer Pillar *2 Side Panel Gusset
*3 Front Body Pillar Lower Reinforce *4 Side Inner Panel
*5 Rocker Outer Panel - -


K127181

K127182