Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR
BM2660E _01 Vehicle Exterior _054376 BODY WELD POINT _0264584 CENTER BODY PILLAR F

BODY WELD POINT  CENTER BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K127144

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

REMOVAL POINT
1.

Carefully cut the rocker outer panel so not to damage *a.

2.

*b indicates the location of the foamed sealing material. Be careful when cutting as the foamed sealing material is located near the cutting position.

3.

*c is reused.


K127183C01
2.615,1.594 2.896,1.167 false 6.615,8.542 6.927,8.698 0.313,0.156 10 false *d 1.854,5.813 2.729,6.031 0.875,0.219 10 false 30 (1.18) 4.625,5.76 5.313,5.969 0.688,0.208 10 false 110 (4.33) 2.917,3.302 3.563,3.531 0.646,0.229 10 false 180 (7.09) 2.198,0.969 2.844,1.198 0.646,0.229 10 false 60 (2.36) 1.708,0.74 2.354,0.938 0.646,0.198 10 false 30 (1.18) 2.875,0.927 3.104,1.135 0.229,0.208 10 false *a
*d mm (in.) - -


K127184C01
1.135,1.458 0.854,1.01 false 1.833,1.458 1.781,0.969 false 6.656,8.542 6.969,8.698 0.313,0.156 10 false *d 2.365,4.75 2.969,5.042 0.604,0.292 10 false 40 (1.57) 0.677,2.042 1.333,2.25 0.656,0.208 10 false 130 (5.12) 2.385,2.031 3.229,2.25 0.844,0.219 10 false 150 (5.91) 2.708,1.052 3.448,1.281 0.74,0.229 10 false 20 (0.79) 0.75,0.813 1.063,1.01 0.313,0.198 10 false *b 1.708,0.76 2.021,0.958 0.313,0.198 10 false *c
*d mm (in.) - -



INSTALLATION


Symbol Meaning
K108818

Remove Weld Points
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld

INSTALLATION POINT
1.

Before temporarily installing the new parts, weld the rocker outer panel, center body pillar upper reinforce and center body pillar lower reinforce with the standard number of welding points.

2.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

3.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimension diagram)

4.

After welding the rocker outer panel, center body pillar upper reinforce and center body pillar lower reinforce to the vehicle side, install the center body outer pillar.

5.

*a indicates the location of the foamed sealing material. Be careful when welding as the foamed sealing material is located near the area that is cut and joined together.

6.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

7.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K127185C01
1.573,3.656 1.854,3.344 false 5.771,5.375 5.406,4.906 false 2.958,6.552 2.552,6.979 false 1.385,3.646 1.635,3.875 0.25,0.229 10 false *1 5.281,4.719 5.594,4.875 0.313,0.156 10 false *2 3,6.375 3.313,6.531 0.313,0.156 10 false *3 6.635,8.49 6.948,8.646 0.313,0.156 10 false *b 3.646,3.604 5.177,3.802 1.531,0.198 10 false 120 (4.72) 6.188,1.302 6.854,1.531 0.667,0.229 10 false 50 (1.97) 3.542,1 4.146,1.219 0.604,0.219 10 false 30 (1.18) 1.698,0.948 2.354,1.125 0.656,0.177 10 false 60 (2.36) 1.031,0.781 1.688,0.958 0.656,0.177 10 false 110 (4.33)
*1 Rocker Outer Panel *2 Center Body Pillar Upper Reinforce
*3 Center Body Pillar Lower Reinforce - -
*b mm (in.) - -


K127186C01
5.042,2.677 5.698,2.344 false 4.427,3.771 4.115,4.854 false 3.052,6.24 2.125,6.24 false 5.74,2.229 6.052,2.385 0.313,0.156 10 false *1 4,4.885 4.313,5.042 0.313,0.156 10 false *2 3.115,6.146 3.531,6.365 0.417,0.219 10 false *3
*1 Center Body Pillar Upper Reinforce *2 Rocker Outer Panel
*3 Center Body Pillar Lower Reinforce - -


K127187C01
3.333,1.698 4.219,1.354 false 4.26,6.438 3.958,5.771 false 4.302,1.26 4.615,1.417 0.313,0.156 10 false *1 3.865,5.563 4.177,5.76 0.313,0.198 10 false *a
*1 Center Body Outer Pillar - -