Home › Vehicle Exterior › BODY PANEL › ROCKER PANEL
BM2660E _01 Vehicle Exterior _054376 BODY WELD POINT _0264588 ROCKER PANEL F

BODY WELD POINT  ROCKER PANEL  CUT AND JOIN REPLACEMENT SECTIONS (LARGE AREAS)  


K127148

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

REMOVAL POINT
1.

Carefully cut the rocker outer panel so not to damage *a.


K127194C01
2.438,3.667 2.75,3.198 false 6.688,8.563 7,8.719 0.313,0.156 10 false *b 2.521,6.271 3.115,6.5 0.594,0.229 10 false 20 (0.79) 2.094,5.76 2.688,5.99 0.594,0.229 10 false 30 (1.18) 1.135,5.792 1.729,6.021 0.594,0.229 10 false 30 (1.18) 5.385,5.896 6.188,6.125 0.802,0.229 10 false 110 (4.33) 1.646,3.063 2.333,3.271 0.688,0.208 10 false 60 (2.36) 1.406,2.781 2.031,2.979 0.625,0.198 10 false 75 (2.95) 3.292,1.167 3.885,1.365 0.594,0.198 10 false 30 (1.18) 2.708,2.979 3.021,3.177 0.313,0.198 10 false *a
*b mm (in.) - -



INSTALLATION


Symbol Meaning
K108818

Remove Weld Points
K108821

Spot Weld
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld

INSTALLATION POINT
1.

Before temporarily installing the new parts, weld the rocker outer panel, center body pillar upper reinforce and center body pillar lower reinforce with the standard number of welding points.

2.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

3.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

4.

After welding the rocker outer panel, center body pillar upper reinforce and center body pillar lower reinforce to the vehicle side, install the center body outer pillar.

5.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

6.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

7.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K127195C01
1.75,3.833 1.75,3.365 false 1.323,5.292 1.323,4.823 false 5.646,4.104 5.646,3.635 false 1.635,3.865 1.948,4.021 0.313,0.156 10 false *1 5.583,4.135 5.896,4.292 0.313,0.156 10 false *2 1.271,4.604 1.583,4.76 0.313,0.156 10 false *3 6.573,8.5 6.885,8.656 0.313,0.156 10 false *a 0.938,0.844 1.521,1.073 0.583,0.229 10 false 60 (2.36) 1.635,0.833 2.219,1.063 0.583,0.229 10 false 75 (2.95) 3.438,0.771 4.042,1 0.604,0.229 10 false 30 (1.18) 2.844,0.969 3.448,1.156 0.604,0.188 10 false 30 (1.18) 4.604,3.01 5.167,3.292 0.563,0.281 10 false 60 (2.36) 3.292,3.646 4.104,3.896 0.813,0.25 10 false 120 (4.72) 2.333,7.604 3.146,7.854 0.813,0.25 10 false 290 (11.42)
*1 Rocker Outer Panel *2 Center Body Pillar Upper Reinforce
*3 Center Body Pillar Lower Reinforce - -
*a mm (in.) - -


K127196C01
4.531,7.771 5.104,8.292 false 5.885,3.188 6.406,2.667 false 1.313,3 1.771,2.385 false 3.135,1.938 3.594,1.323 false 1.219,3.021 1.531,3.177 0.313,0.156 10 false *1 3.552,1.135 3.865,1.292 0.313,0.156 10 false *2 6.417,2.542 6.729,2.698 0.313,0.156 10 false *3 5.177,8.26 5.49,8.417 0.313,0.156 10 false *4
*1 Rocker Outer Panel *2 Center Body Pillar Upper Reinforce
*3 Center Body Pillar Lower Reinforce *4 Center Body Outer Pillar