Home › General › ENGINE › 3UR-FE ENGINE
NM2660E _V1 General _054359 ENGINE _0264892 3UR-FE ENGINE UN GENERAL/CONTROL/DETAILS F

ENGINE  3UR-FE ENGINE  GENERAL/CONTROL/DETAILS  VALVE MECHANISM  


General


a.

Each cylinder of this engine has 2 intake valves and 2 exhaust valves. Intake and exhaust efficiency has been increased due to the larger total port areas.


b.

This engine uses roller rocker arms with built-in needle bearings. This reduces the friction that occurs between the cams and the valve rocker arms that push the valves down, thus improving fuel economy.


c.

Hydraulic lash adjusters, which maintain a constant zero valve clearance through the use of oil pressure and spring force, are used.


d.

To ensure highly accurate valve timing, separate primary timing chains are driven by the crankshaft in order to rotate the intake camshafts of the left and right banks. The exhaust camshafts are driven by the intake camshaft of the respective bank via secondary timing chains.


e.

This engine has a Dual Variable Valve Timing-intelligent (VVT-i) system which controls the intake and exhaust camshafts to provide optimal valve timing in accordance with driving conditions. As a result, lower fuel consumption, higher engine performance, and reduced exhaust emissions have been achieved.

W128382C01
5.833,1.458 5.76,1.052 true 3.073,1.167 4.219,0.521 4.219,0.521 4.104,1.896 true 5.656,1.781 5.469,1.479 true 5.552,3.396 5.25,2.99 true 5.875,2.854 5.49,2.552 true 6.167,2.219 5.667,2.094 true 6.24,1.896 5.917,1.865 true 6.042,2.583 5.521,2.365 true 2.563,1.469 2.396,0.385 2.396,0.385 3.833,2.469 true 1.854,1.385 1.51,0.729 1.51,0.729 3.125,2.042 true 2.177,2.104 1.26,3.615 1.26,3.615 2.927,2.792 true 2.26,0.188 2.521,0.406 0.26,0.219 10 false *1 1.354,0.563 1.615,0.781 0.26,0.219 10 false *2 1.073,3.552 1.333,3.771 0.26,0.219 10 false *3 4.198,0.354 4.458,0.573 0.26,0.219 10 false *4 5.646,0.875 5.906,1.094 0.26,0.219 10 false *5 5.302,1.292 5.563,1.51 0.26,0.219 10 false *6 6.26,1.813 6.521,2.031 0.26,0.219 10 false *11 6.198,2.146 6.458,2.365 0.26,0.219 10 false *10 6.094,2.531 6.354,2.75 0.26,0.219 10 false *9 5.917,2.833 6.177,3.052 0.26,0.219 10 false *8 5.552,3.427 5.813,3.646 0.26,0.219 10 false *7
*1 Exhaust Camshaft *2 Secondary Timing Chain
*3 Primary Timing Chain *4 Intake Camshaft
*5 Valve Rocker Arm *6 Valve Spring Retainer
*7 Valve *8 Valve Spring Seat
*9 Valve Guide Bush *10 Compression Spring
*11 Hydraulic Lash Adjuster - -




Camshaft


a.

The camshafts are made of cast iron alloy.


b.

Oil passages are provided in the intake and exhaust camshafts in order to supply engine oil to the VVT-i system.


c.

VVT-i controllers are installed on the front of the intake and exhaust camshafts to vary the timing of the intake and exhaust valves.


d.

Together with the use of the roller rocker arms, the cam profile has been optimized. This results in increased valve lift when the valve begins to open and as it finishes closing, helping to achieve enhanced output performance.

W128383C02
0.448,3.104 2.438,4.208 1.99,1.104 0.448,4.344 2.438,5.448 1.99,1.104 3.729,3.646 3.729,3.333 true 6.521,1.042 6.333,1.688 6.333,1.688 6.115,1.042 true 4.813,3.188 4.813,2.802 true 3.031,3.188 3.031,2.802 true 0.729,1.385 0.729,1 true 2.031,1.156 2.031,0.771 true 3.281,1.313 3.281,0.927 true 4.448,2.042 4.448,1.656 true 1.208,2.375 1.594,2.031 true 3.313,2.51 1.958,2.698 1.958,2.698 1.802,2.177 true 2.146,3.656 1.542,3.438 true 2.219,4.75 1.531,4.948 true 1.948,0.594 2.177,0.802 0.229,0.208 10 false *1 3.667,3.688 3.896,3.896 0.229,0.208 10 false *2 0.646,0.833 0.875,1.042 0.229,0.208 10 false *2 1.833,2.74 2.063,2.948 0.229,0.208 10 false *2 1.094,2.385 1.323,2.594 0.229,0.208 10 false *3 2.969,3.219 3.198,3.427 0.229,0.208 10 false *3 0.5,3.115 0.729,3.323 0.229,0.208 10 false *c 0.469,4.365 0.698,4.573 0.229,0.208 10 false *d 5.885,0.594 6.115,0.802 0.229,0.208 10 false *a 6.271,1.74 6.552,1.969 0.281,0.229 10 false *b 3.219,0.76 3.448,0.969 0.229,0.208 10 false *6 4.396,1.49 4.625,1.698 0.229,0.208 10 false *5 4.75,3.208 4.979,3.417 0.229,0.208 10 false *4 2.208,3.594 2.438,3.802 0.229,0.208 10 false *e 2.26,4.656 2.49,4.865 0.229,0.208 10 false *e 6.604,0.583 6.833,0.792 0.229,0.208 10 false *a
*1 No. 2 Camshaft (Exhaust) *2 VVT-i Controller
*3 Timing Rotor *4 No. 4 Camshaft (Exhaust)
*5 No. 3 Camshaft (Intake) *6 No. 1 Camshaft (Intake)
*a Increased Valve Lift *b Optimized Profile of Camshaft Lobe
*c Cross Section of End of Intake Camshaft *d Cross Section of End of Exhaust Camshaft
*e Oil Passage - -




Timing Chain and Chain Tensioner


a.

Both the primary and secondary chains use roller chains with a pitch of 9.525 mm (0.375 in.).


b.

A timing chain tensioner is provided for each primary timing chain and secondary timing chain on each bank.


c.

Both the primary and secondary chain tensioners use a spring and oil pressure to maintain proper chain tension at all times. The tensioners suppress noise generated by the timing chains.


d.

The chain tensioner for the primary timing chain is a ratchet type with a non-return mechanism. Furthermore, an oil pocket creates oil pressure when the engine is started, and simultaneously applies oil pressure to the chain tensioner. This prevents the timing chain from flapping and reduces noise.

W128384C01
4.802,1.208 4.448,0.885 true 4.188,2.063 3.896,2.302 true 5.031,1.552 4.729,2.354 true 2.104,3.177 1.51,3.677 true 2.094,3.948 1.531,3.781 true 0.958,3.167 1.469,3.552 true 0.979,3.833 1.448,3.594 true 1.417,5.625 1.25,5.198 true 2.281,5.885 1.969,5.885 true 1.49,6.26 1.688,5.938 true 3.135,6.156 4.615,5.323 true 3.313,5.344 4.25,4.865 true 3.135,3.948 2.927,3.427 true 4,3.979 3.917,3.313 true 5.552,4.333 5.354,3.25 true 6.448,4.01 6.604,3.51 true 6.198,5.479 5.458,4.99 true 6.031,6.156 5.052,5.385 true 6.24,4.927 6.24,4.271 true 4.292,0.75 4.594,1.01 0.302,0.26 10 false *1 3.729,2.292 4.031,2.552 0.302,0.26 10 false *2 4.635,2.375 4.938,2.635 0.302,0.26 10 false *3 0.802,3.031 1.104,3.292 0.302,0.26 10 false *4 0.823,3.771 1.125,4.031 0.302,0.26 10 false *5 2.115,3.021 2.417,3.281 0.302,0.26 10 false *6 2.156,3.906 2.458,4.167 0.302,0.26 10 false *7 1.125,5.031 1.427,5.292 0.302,0.26 10 false *8 2.302,5.792 2.604,6.052 0.302,0.26 10 false *10 1.375,6.271 1.677,6.531 0.302,0.26 10 false *9 2.917,6.104 3.219,6.365 0.302,0.26 10 false *14 3.083,5.292 3.385,5.552 0.302,0.26 10 false *13 6,6.177 6.302,6.438 0.302,0.26 10 false *15 6.208,5.49 6.51,5.75 0.302,0.26 10 false *16 6.135,4.927 6.438,5.188 0.302,0.26 10 false *17 2.76,3.25 3.063,3.51 0.302,0.26 10 false *12 3.781,3.135 4.083,3.396 0.302,0.26 10 false *11 5.229,3.063 5.531,3.323 0.302,0.26 10 false *19 6.521,3.323 6.823,3.583 0.302,0.26 10 false *18 3.219,0.458 3.521,0.719 0.302,0.26 10 false *a 0.51,2.771 0.813,3.031 0.302,0.26 10 false *b 0.521,4.979 0.823,5.24 0.302,0.26 10 false *c
*1 Gasket *2 Chain Tensioner (Primary)
*3 Oil Pocket *4 Ball
*5 Ball Spring *6 Main Spring
*7 Plunger *8 Spring
*9 Cam Spring *10 Cam
*11 Chain Damper *12 Secondary Timing Chain RH
*13 Chain Slipper *14 Primary Timing Chain RH
*15 Primary Timing Chain LH *16 Chain Damper
*17 Secondary Timing Chain LH *18 Secondary Chain Tensioner
*19 Chain Slipper - -
*a Chain Tensioner (Primary) LH Side *b Chain Tensioner (Secondary) RH Side
*c Chain Tensioner (Primary) RH Side - -




Timing Chain Cover


a.

The timing chain cover has an integrated construction consisting of the cooling system (water pump and water passage) and the lubrication system (oil pump and oil passage). Thus, the number of parts has been reduced to reduce weight.


b.

An oil jet is provided in the oil pump cover to lubricate the timing chains.

W128385C01
2.135,1.635 2.646,0.74 true 1.219,1.479 0.927,0.885 true 0.844,2.74 0.844,2.302 true 2.396,3.083 2.313,2.677 true 4.719,1.063 4.563,0.531 true 4.021,2.396 3.802,1.917 true 4.281,2.438 4.521,1.979 true 4.802,2.938 4.667,2.521 true 5.417,3.042 5.323,2.302 true 0.792,0.719 1.073,0.969 0.281,0.25 10 false *1 0.792,2.781 1.073,3.031 0.281,0.25 10 false *2 2.365,3.125 2.646,3.375 0.281,0.25 10 false *3 2.615,0.583 2.896,0.833 0.281,0.25 10 false *4 4.469,0.365 4.75,0.615 0.281,0.25 10 false *3 3.688,1.76 3.969,2.01 0.281,0.25 10 false *5 4.479,1.813 4.76,2.063 0.281,0.25 10 false *6 4.771,2.99 5.052,3.24 0.281,0.25 10 false *7 5.385,3.073 5.667,3.323 0.281,0.25 10 false *8 2.302,3.385 2.583,3.635 0.281,0.25 10 false *a 5.521,3.385 5.802,3.635 0.281,0.25 10 false *b
*1 Water Pump Gasket *2 Water Pump
*3 Timing Chain Cover *4 Water Pump Swirl Chamber
*5 Oil Pump Cover *6 Oil Jet
*7 Oil Pump Rotor *8 Oil Pump Chamber
*a View from Front Side *b View from Back Side




Hydraulic Lash Adjuster


a.

The hydraulic lash adjusters, which are located at the fulcrum (pivot point) of the roller rocker arms, each consist primarily of a plunger, plunger spring, check ball, and check ball spring.


b.

The engine oil that is supplied from the cylinder head and the built-in spring actuate the hydraulic lash adjuster. The oil pressure and the spring force that act on the plunger push the roller rocker arm against the cam, in order to adjust the clearance between the valve stem and rocker arm. This prevents the generation of noise during the opening and closing of the valves. As a result, engine noise is reduced.

W128386C02
2.021,0.917 2.021,0.427 true 1.583,1.875 1.104,1.333 true 1.865,2.49 1.021,1.958 true 1.813,2.656 0.948,2.417 true 1.729,2.823 1.042,3.135 true 4.073,1.458 3.615,0.708 true 4.323,0.813 4.24,0.417 true 4.552,1.438 5.083,0.656 true 4.156,1.719 5.938,1.25 true 1.958,0.25 2.219,0.469 0.26,0.219 10 false *1 0.969,1.135 1.229,1.354 0.26,0.219 10 false *a 0.781,2.292 1.031,2.5 0.25,0.208 10 false *3 0.875,3.031 1.125,3.24 0.25,0.208 10 false *4 3.469,0.531 3.719,0.74 0.25,0.208 10 false *5 4.156,0.208 4.406,0.417 0.25,0.208 10 false *6 5.104,0.469 5.354,0.677 0.25,0.208 10 false *7 0.865,1.865 1.115,2.073 0.25,0.208 10 false *2 5.958,1.156 6.219,1.375 0.26,0.219 10 false *a
*1 Plunger *2 Check Ball
*3 Check Ball Spring *4 Plunger Spring
*5 Hydraulic Lash Adjuster *6 Cam
*7 Roller Rocker Arm - -
*a Oil Passage - -


HINT:

Valve clearance adjustment is not necessary because hydraulic lash adjusters are used on this model.