Home › General › ENGINE › 1UR-FE ENGINE
NM2660E _V1 General _054359 ENGINE _0265192 1UR-FE ENGINE UN GENERAL/CONTROL/DETAILS F

ENGINE  1UR-FE ENGINE  GENERAL/CONTROL/DETAILS  ENGINE CONTROL SYSTEM  


General


a.

The engine control system has the following features. The ECM controls these systems:

System Outline

*: Models with air injection control

Sequential Multiport Fuel Injection (SFI)
·

An L-type EFI system directly detects the intake air mass using a hot wire type intake mass air flow meter sub-assembly.

·

An independent injection system (in which fuel is injected once into each intake port for each 2 revolutions of the crankshaft) is used.

·

Fuel injection takes 2 forms:

-

Synchronous injection, in which injection always occurs at the same timing relative to the firing order.

-

Non-synchronous injection, in which injection is effected regardless of the crankshaft angle.


·

Synchronous injection is further divided into group injection during a cold start, and independent injection after the engine is started.


Electronic Spark Advance (ESA)
·

Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking.

·

This system selects the optimal ignition timing in accordance with the signals received from the sensors and sends the (IGT) ignition signal to the igniter.


Electronic Throttle Control System-intelligent (ETCS-i) Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort and the condition of the engine and the vehicle.
Dual Variable Valve Timing-intelligent (VVT-i) Controls the intake and exhaust camshafts to optimal valve timing in accordance with the engine operating conditions.
Acoustic Control Induction System (ACIS) The intake air passages are switched based on engine speed and throttle valve opening angle to provide high performance in all engine speed ranges.
Fuel Pump Control
·

Based on signals from the ECM, the fuel pump control ECU controls the fuel pump in linear control.

·

The fuel pump is stopped when the SRS airbag is deployed.


Air Injection Control* The ECM controls the air injection time based on the signals from the crank position sensor, engine coolant temperature sensor, intake mass air flow meter sub-assembly and air pressure sensor.
Starter Control (Cranking Hold Function) Once the engine switch is pushed while the brake pedal is depressed, this control continues to operate the starter until the engine starts.
Air Fuel Ratio Sensor and Oxygen Sensor Heater Control Maintains the temperature of the air fuel ratio sensors or oxygen sensors at an appropriate level to increase the detection accuracy of the exhaust gas oxygen concentration.
Air Conditioning Cut-off Control By turning the air conditioning compressor on or off in accordance with the engine condition, driveability is maintained.
Evaporative Emission Control The ECM controls the purge flow of evaporative emissions (HC) in the charcoal canister in accordance with the engine conditions.
Engine Immobiliser Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key.
Brake Override System The driving torque is restricted when the brake pedal is depressed while the accelerator pedal is depressed. (For the Activation Conditions and Inspection Method, refer to the Repair Manual.)
Diagnosis When the ECM detects a malfunction, it records the malfunction and memorizes information related to the fault.
Fail-safe When the ECM detects a malfunction, it stops or controls the engine according to the data already stored in the memory.



Construction


a.

The configuration of the engine control system is as shown in the following chart.

W133289E01
0.375,0.094 2.271,0.865 1.896,0.771 10 false Intake Mass Air Flow Meter Sub-assembly 0.406,1.104 2.323,1.479 1.917,0.375 10 false Intake Air Temperature Sensor 0.563,1.708 2.302,2.073 1.74,0.365 10 false Crank Position Sensor 0.635,2.292 2.302,2.677 1.667,0.385 10 false Cam Position Sensor 0.177,2.885 2.448,3.281 2.271,0.396 10 false Engine Coolant Temperature Sensor 0.219,3.49 2.479,3.885 2.26,0.396 10 false Accelerator Pedal Sensor Assembly 0.469,4.104 2.417,4.469 1.948,0.365 10 false Throttle Position Sensor 0.625,4.708 2.406,5.073 1.781,0.365 10 false Knock Control Sensor 0.74,5.229 2.375,5.594 1.635,0.365 10 false Bank 1, Sensor 1 0.74,5.646 2.375,6.01 1.635,0.365 10 false Bank 1, Sensor 2 0.74,6.063 2.375,6.427 1.635,0.365 10 false Bank 2, Sensor 1 0.74,6.479 2.375,6.844 1.635,0.365 10 false Bank 2, Sensor 2 0.708,7.198 2.406,7.563 1.698,0.365 10 false VVT Sensors (Intake) 0.656,7.792 2.354,8.156 1.698,0.365 10 false VVT Sensors (Exhaust) 0.5,8.406 2.396,8.75 1.896,0.344 10 false Stop Light Switch Assembly 3.396,3.646 3.854,4.094 0.458,0.448 10 false ECM 5.01,0.615 6.948,0.99 1.938,0.375 10 false No. 1 Fuel Injector Assembly 5.813,0.104 6.917,0.469 1.104,0.365 10 false EFI 5.01,1.031 6.948,1.406 1.938,0.375 10 false No. 2 Fuel Injector Assembly 5.01,1.448 6.948,1.823 1.938,0.375 10 false No. 3 Fuel Injector Assembly 5.01,1.875 6.948,2.25 1.938,0.375 10 false No. 4 Fuel Injector Assembly 5.01,2.281 6.948,2.656 1.938,0.375 10 false No. 5 Fuel Injector Assembly 5.01,2.708 6.948,3.083 1.938,0.375 10 false No. 6 Fuel Injector Assembly 5.01,3.125 6.948,3.5 1.938,0.375 10 false No. 7 Fuel Injector Assembly 5.01,3.552 6.948,3.927 1.938,0.375 10 false No. 8 Fuel Injector Assembly 5.667,4.188 7.042,4.563 1.375,0.375 10 false ESA 5.052,4.677 6.625,5.042 1.573,0.365 10 false Ignition Coil (with Igniter) 5.385,5.104 6.635,5.479 1.25,0.375 10 false No. 1, 4, 6, 7 5.115,5.667 6.688,6.031 1.573,0.365 10 false Ignition Coil (with Igniter) 5.385,6.063 6.635,6.438 1.25,0.375 10 false No. 2, 3, 5, 8 4.938,6.729 5.792,7.104 0.854,0.375 10 false Spark Plug 5.938,6.729 6.792,7.104 0.854,0.375 10 false Spark Plug 4.896,7.167 5.75,7.542 0.854,0.375 10 false No. 2, 3, 5, 8 5.854,7.146 6.781,7.531 0.927,0.385 10 false No. 1, 4, 6, 7 5.583,7.75 6.354,8.125 0.771,0.375 10 false ETCS-i 5.188,8.271 6.708,8.656 1.521,0.385 10 false Throttle Control Motor

W133290E01
5.375,0.083 7.021,0.438 1.646,0.354 10 false Dual VVT-i (Intake) 5,0.615 6.792,1.385 1.792,0.771 10 false Camshaft Timing Oil Control Valve (Bank 1) 5.042,1.583 6.833,2.354 1.792,0.771 10 false Camshaft Timing Oil Control Valve (Bank 2) 0.271,0.115 2.292,0.844 2.021,0.729 10 false Transfer Neutral Position Switch 0.604,1.208 2.25,1.563 1.646,0.354 10 false 4WD Control Switch 0.417,1.896 2.292,2.281 1.875,0.385 10 false Air Pressure Sensor (Bank 1) 0.417,2.594 2.292,2.979 1.875,0.385 10 false Air Pressure Sensor (Bank 2) 0.677,3.281 2.292,3.708 1.615,0.427 10 false Generator Assembly 0.375,4 2.281,4.75 1.906,0.75 10 false Power Steering Oil Pressure Sensor 0.406,5.125 2.313,5.875 1.906,0.75 10 false Air Conditioning Amplifier Assembly 0.417,6.229 2.323,6.979 1.906,0.75 10 false Park/Neutral Position Switch Assembly 0.656,7.052 2.104,7.458 1.448,0.406 10 false - Neutral Start Signal 0.635,7.448 2.458,7.854 1.823,0.406 10 false - Shift Lever Position Signal 0.385,8.188 2.292,8.75 1.906,0.563 10 false Transmission Control Switch 5.344,2.896 6.99,3.25 1.646,0.354 10 false Dual VVT-i (Exhaust) 5.063,3.417 6.854,4.188 1.792,0.771 10 false Camshaft Timing Oil Control Valve (Bank 1) 5.063,4.375 6.854,5.146 1.792,0.771 10 false Camshaft Timing Oil Control Valve (Bank 2) 5.677,5.667 6.844,6.042 1.167,0.375 10 false ACIS 5.688,6.198 6.854,6.573 1.167,0.375 10 false VSV 5.417,7.083 6.583,7.458 1.167,0.375 10 false Fuel Pump Control 5.104,7.604 6.865,7.979 1.76,0.375 10 false Fuel Pump Control ECU 5.521,8.24 6.896,8.615 1.375,0.375 10 false Fuel Pump 3.406,3.719 3.854,4.177 0.448,0.458 10 false ECM

W133291E01
3.385,3.99 3.823,4.448 0.438,0.458 10 false ECM 0.604,0.104 2.458,0.469 1.854,0.365 10 false Air Fuel Ratio Sensor 0.719,0.625 2.385,0.979 1.667,0.354 10 false (Bank 1, Sensor 1) 0.719,1.042 2.385,1.396 1.667,0.354 10 false (Bank 2, Sensor 1) 0.792,1.896 2.448,2.25 1.656,0.354 10 false Oxygen Sensor 0.708,2.427 2.375,2.781 1.667,0.354 10 false (Bank 1, Sensor 2) 0.719,2.833 2.385,3.188 1.667,0.354 10 false (Bank 2, Sensor 2) 5.219,0.115 7.042,0.438 1.823,0.323 10 false Air Injection Control*2 5.021,0.698 6.729,1.219 1.708,0.521 10 false Air Injection Control Driver 4.927,1.573 6.771,1.969 1.844,0.396 10 false Air Switching Valve (Bank 1) 5.51,2.125 6.771,2.521 1.26,0.396 10 false Air Pump 5.531,2.635 6.719,3.031 1.188,0.396 10 false Heater*3 5.531,3.302 6.719,3.698 1.188,0.396 10 false ASV Relay 4.927,4.021 6.771,4.417 1.844,0.396 10 false Air Switching Valve (Bank 2) 0.01,7.635 2.979,8 2.969,0.365 10 false *1: Models with cruise control system 0,8.052 2.969,8.417 2.969,0.365 10 false *2: Models compliant with air injection control 0.76,3.677 2.427,4.031 1.667,0.354 10 false Pattern Select Switch 0.448,4.417 2.427,4.76 1.979,0.344 10 false Cruise Control Main Switch*1 0.594,5.135 2.365,5.5 1.771,0.365 10 false Immobiliser Code ECU 0.74,5.854 2.417,6.25 1.677,0.396 10 false Combination Meter 1.135,6.385 2.354,6.781 1.219,0.396 10 false MIL 0.573,6.917 2.281,7.271 1.708,0.354 10 false Vehicle Speed Signal 5.417,4.74 6.865,5.115 1.448,0.375 10 false Starter Control 5.365,5.271 6.875,5.667 1.51,0.396 10 false Main Body ECU 5.573,5.896 6.896,6.271 1.323,0.375 10 false ACC Relay 5.417,6.438 6.927,6.833 1.51,0.396 10 false Starter Cut Relay 5.302,7.083 6.854,7.833 1.552,0.75 10 false Prak/Neutral Position Switch Assembly 5.313,8.125 6.823,8.521 1.51,0.396 10 false Starter Relay 0.01,8.469 2.979,8.844 2.969,0.375 10 false *3: Models compliant with air injection heater

W133292E01
0.792,0.094 2.271,0.469 1.479,0.375 10 false EFI Main Relay 0.948,0.792 2.292,1.167 1.344,0.375 10 false IG2 Relay 1.052,1.49 2.396,1.865 1.344,0.375 10 false Battery 1.083,2.208 2.24,2.594 1.156,0.385 10 false DLC3 3.417,3.563 3.844,4.135 0.427,0.573 10 false ECM 0.385,3.083 2.469,3.438 2.083,0.354 10 false Center Airbag Sensor Assembly 0.552,3.792 2.417,4.146 1.865,0.354 10 false Network Gateway ECU 0.75,4.479 2.458,4.833 1.708,0.354 10 false Skid Control ECU 0.594,5.177 2.458,5.531 1.865,0.354 10 false Distance Control ECU*1 0.281,5.885 2.458,6.635 2.177,0.75 10 false Millimeter Wave Radar Sensor*1 4.979,0.104 7.01,0.875 2.031,0.771 10 false Air Fuel Ratio Sensor and Oxygen Sensor Heater Control 5.052,0.948 7.042,1.385 1.99,0.438 10 false Air Fuel Ratio Sensor Heater 5.344,1.458 6.948,1.833 1.604,0.375 10 false (Bank 1, Sensor 1) 5.365,1.865 6.969,2.24 1.604,0.375 10 false (Bank 2, Sensor 1) 5.229,2.302 6.99,2.76 1.76,0.458 10 false Oxygen Sensor Heater 5.365,2.813 6.969,3.188 1.604,0.375 10 false (Bank 1, Sensor 2) 5.375,3.229 6.979,3.604 1.604,0.375 10 false (Bank 2, Sensor 2) 4.958,5.646 6.885,6 1.927,0.354 10 false Evaporative Emission Control 5.396,6.188 6.906,6.542 1.51,0.354 10 false VSV (for EVAP) 0.104,6.854 3.583,7.188 3.479,0.333 10 false *1: Models with cruise control system 2.177,2.802 2.708,3.063 0.531,0.26 10 false CAN*2 2.542,5.469 3.073,5.729 0.531,0.26 10 false CAN*3 0.115,7.208 3.594,7.542 3.479,0.333 10 false *2: V bus 0.115,7.583 3.594,7.917 3.479,0.333 10 false *3: Movement control bus



Layout of Main Components


W133023C01
2.969,2.021 2.563,1.125 true 2.427,2.156 2.021,1.26 true 1.719,2.594 1.198,1.76 true 2.448,2.5 1.563,3.51 true 2.198,3.99 3.125,2.677 true 2.792,4.25 3.25,2.688 true 3.531,4.521 3.51,2.948 true 4.115,4.427 3.74,2.75 true 4.698,4.448 4.146,3.042 true 5.99,1.625 5.031,2.24 true 4.854,0.5 4.771,2.198 true 3.927,0.646 3.875,2.531 true 2.458,0.906 2.771,1.063 0.313,0.156 10 false *1 1.885,1.063 2.198,1.219 0.313,0.156 10 false *2 1.042,1.573 1.354,1.729 0.313,0.156 10 false *3 1.417,3.542 1.729,3.698 0.313,0.156 10 false *4 2.104,4.01 2.417,4.167 0.313,0.156 10 false *5 2.677,4.313 2.99,4.469 0.313,0.156 10 false *6 3.458,4.552 3.771,4.708 0.313,0.156 10 false *7 4.083,4.49 4.396,4.646 0.313,0.156 10 false *8 4.698,4.5 5.01,4.656 0.313,0.156 10 false *9 6.052,1.542 6.521,1.698 0.469,0.156 10 false *10 4.74,0.333 5.208,0.49 0.469,0.156 10 false *11 3.823,0.438 4.292,0.594 0.469,0.156 10 false *12
*1 ECM *2 Intake Mass Air Flow Meter Sub-assembly
·

Intake AirTemperature Sensor


*3 Air Pump *4 Throttle Body
·

Throttle Position Sensor

·

Throttle Control Motor


*5 Air Fuel Ratio Sensor (Bank 2, Sensor 1) *6 Air Injection Control Driver
*7 Air Fuel Ratio Sensor (Bank 1, Sensor 1) *8 Oxygen Sensor (Bank 2, Sensor 2)
*9 Oxygen Sensor (Bank 1, Sensor 2) *10 Fuel Suction with Pump and Gauge Tube Assembly
*11 Fuel Pump Control ECU *12 Charcoal Canister


W133024C01
2.708,0.208 3.219,0.24 true 1.115,1.406 2.969,1.813 true 0.979,3.208 1.948,3.01 true 2.427,0.135 2.74,0.292 0.313,0.156 10 false *1 0.896,1.313 1.208,1.469 0.313,0.156 10 false *2 0.802,3.156 1.115,3.313 0.313,0.156 10 false *3 0.052,0.052 0.427,0.292 0.375,0.24 12 false A:
*A LHD Models - -
*1 MIL *2 DLC3
*3 Accelerator Pedal Sensor Assembly - -


W133025C01
1.625,0.823 1.156,0.458 true 1.948,1.552 0.625,2.313 true 2.24,1.51 1.26,2.719 true 2.396,1.542 1.76,3.042 true 2.51,1.719 2.417,3.042 true 2.656,1.656 2.979,2.979 true 2.531,1.396 3.531,1.896 true 2.781,1.115 3.354,1 true 2.333,0.865 2.677,0.5 true 5.188,0.917 4.927,0.594 true 4.719,1.219 4.375,0.979 true 4.646,2.813 4.833,2.604 true 6.354,2.479 6.125,1.667 true 6.635,2.25 6.406,1.438 true 6.646,0.896 6.313,1.271 true 6,1.323 6.24,0.521 true 3.104,3.833 3.292,4.635 true 2.719,3.938 3.01,4.5 true 2.521,4.135 3.01,4.802 true 2.188,4.354 2.573,4.542 true 2.146,4.646 2.531,4.833 true 2.177,5.229 2.552,5.146 true 2.198,5.49 2.573,5.406 true 2.375,6.25 3.021,5.115 true 3.052,5.417 2.688,6.51 true 3.302,5.406 3.146,6.521 true 3.75,5.427 3.99,6.479 true 4.073,5.51 4.552,6.448 true 4.063,5.24 4.781,6.24 true 4.531,5.51 4.917,5.698 true 4.531,5.208 4.917,5.396 true 4.51,4.583 4.885,4.5 true 4.51,4.885 4.885,4.802 true 4.073,4.885 4.604,3.958 true 4.26,3.865 4.063,4.542 true 3.875,3.792 3.76,4.688 true 0.958,0.333 1.271,0.49 0.313,0.156 10 false *1 0.427,2.281 0.74,2.438 0.313,0.156 10 false *2 1.167,2.75 1.479,2.906 0.313,0.156 10 false *3 1.667,3.094 1.979,3.25 0.313,0.156 10 false *4 2.302,3.052 2.615,3.208 0.313,0.156 10 false *5 2.917,3.021 3.229,3.177 0.313,0.156 10 false *6 3.573,1.844 3.885,2 0.313,0.156 10 false *7 3.406,0.906 3.719,1.063 0.313,0.156 10 false *8 2.677,0.323 2.99,0.479 0.313,0.156 10 false *9 4.76,0.396 5.229,0.552 0.469,0.156 10 false *10 4.146,0.865 4.615,1.021 0.469,0.156 10 false *11 4.469,2.844 4.938,3 0.469,0.156 10 false *12 6.302,2.542 6.771,2.698 0.469,0.156 10 false *13 6.552,2.271 7.021,2.427 0.469,0.156 10 false *14 6.635,0.75 7.104,0.906 0.469,0.156 10 false *15 6.188,0.313 6.656,0.469 0.469,0.156 10 false *16 2.969,3.625 3.438,3.781 0.469,0.156 10 false *17 2.51,3.76 2.979,3.917 0.469,0.156 10 false *18 1.906,4.229 2.375,4.385 0.469,0.156 10 false *19 2.313,3.969 2.781,4.125 0.469,0.156 10 false *18 1.896,4.521 2.365,4.677 0.469,0.156 10 false *19 1.948,5.146 2.417,5.302 0.469,0.156 10 false *19 1.958,5.438 2.427,5.594 0.469,0.156 10 false *19 2.198,6.271 2.667,6.427 0.469,0.156 10 false *18 2.552,6.542 3.021,6.698 0.469,0.156 10 false *18 3.01,6.552 3.479,6.708 0.469,0.156 10 false *17 3.875,6.563 4.344,6.719 0.469,0.156 10 false *17 4.49,6.51 4.958,6.667 0.469,0.156 10 false *18 4.844,6.302 5.313,6.458 0.469,0.156 10 false *18 4.896,4.406 5.365,4.563 0.469,0.156 10 false *19 4.917,4.698 5.385,4.854 0.469,0.156 10 false *19 4.938,5.323 5.406,5.479 0.469,0.156 10 false *19 4.906,5.635 5.375,5.792 0.469,0.156 10 false *19 4.583,3.854 5.052,4.01 0.469,0.156 10 false *18 4.198,3.688 4.667,3.844 0.469,0.156 10 false *18 3.75,3.604 4.219,3.76 0.469,0.156 10 false *17
*1 Air Switching Valve (Bank 2)
·

Air Pressure Sensor


*2 Engine Coolant Temperature Sensor
*3 Cam Position Sensor *4 Camshaft Timing Oil Control Valve (Bank 1, Intake)
*5 Camshaft Timing Oil Control Valve (Bank 1, Exhaust) *6 VVT Sensor (Bank 1, Exhaust)
*7 VVT Sensor (Bank 1, Intake) *8 Air Switching Valve (Bank 1)
·

Air Pressure Sensor


*9 Purge VSV *10 VSV (for ACIS)
*11 ACIS Actuator *12 Crank Position Sensor
*13 VVT Sensor (Bank 2, Exhaust) *14 Camshaft Timing Oil Control Valve (Bank 2, Exhaust)
*15 Camshaft Timing Oil Control Valve (Bank 2, Intake) *16 VVT Sensor (Bank 2, Intake)
*17 Knock Control Sensor *18 Fuel Injector Assembly
*19 Ignition Coil (with Igniter) - -



Main Components of Engine Control System


a.

General

i.

The main components of the 1UR-FE engine control system are as follows:

Components Outline Quantity Function
ECM 32-bit CPU 1 The ECM optimally controls the engine control system to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
Intake Mass Air Flow Meter Sub-assembly Hot-wire Type 1 This sensor has a built-in hot-wire to directly detect the intake air mass and flow rate.
Intake Air Temperature Sensor Thermistor Type 1 This sensor detects the intake air temperature by means of an internal thermistor.
Accelerator Pedal Sensor Assembly Hall IC Type (Non-contact Type) 1 This sensor detects the amount of pedal effort applied to the accelerator pedal.
Throttle Position Sensor Hall IC Type (Non-contact Type) 1 This sensor detects the throttle valve opening angle.
Crank Position Sensor MRE Type (Rotor Teeth/36-2) 1 This sensor detects the engine speed and the crankshaft position.
Cam Position Sensor MRE Type (Rotor Teeth/3) 1 This sensor detects the camshaft position and performs the cylinder identification.
VVT Sensor (Intake) MRE Type (Rotor Teeth/3) 2 (1 each bank) This sensor detects the actual valve timing.
VVT Sensor (Exhaust) MRE Type (Rotor Teeth/3) 2 (1 each bank) This sensor detects the actual valve timing.
Knock Control Sensor Built-in Piezoelectric Element (Flat Type) 4 (2 each bank) This sensor detects an occurrence of the engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking.
Oxygen Sensor Cup Type with Heater 2 (1 each bank) This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force generated in the sensor itself.
Air Fuel Ratio Sensor Planar Type with Heater 2 (1 each bank) As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust emissions. However, it detects the oxygen concentration in the exhaust emissions linearly.
Vacuum Sensor Semiconductor Silicon Chip Type 1 This sensor uses built-in semiconductors to detect the intake manifold pressure.
Engine Coolant Temperature Sensor Thermistor Type 1 This sensor detects the engine coolant temperature by means of an internal thermistor.
Fuel Injector Assembly 12-hole Type 8 This fuel injector contains an electro-magnetically operated nozzle to inject fuel into the intake port.
Camshaft Timing Oil Control Valve Electromagnetic Coil Type 4 (2 each bank) The camshaft timing oil control valve changes the valve timing by switching the oil passage that acts on the camshaft timing gear assembly in accordance with the signals received from the ECM.



b.

Intake Mass Air Flow Meter Sub-assembly

i.

This intake mass air flow meter sub-assembly, which is a slot-in type, allows a portion of the intake air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air, the detection precision is improved and the intake air resistance is reduced.


ii.

This intake mass air flow meter sub-assembly has a built-in intake air temperature sensor.

W128425C01
5.115,1.906 5.594,1.604 true 1.156,1.573 1.396,1.802 0.24,0.229 10 false *a 5.615,1.469 5.854,1.698 0.24,0.229 10 false *1
*1 Intake Air Temperature Sensor - -
*a Air Flow - -




c.

Crank Position Sensor, Cam Position Sensor and VVT Sensor.

i.

General

·

Magnetic Resistance Element (MRE) sensors are used for the crank position, cam position, and VVT sensors.

·

The timing rotor for the crank position sensor is installed on the back end of the crankshaft. The timing rotor has 34 teeth, with 2 teeth missing, at 10° intervals. Based on these teeth, the crank position sensor transmits crankshaft position signals (NE signal) consisting of 33 high and low output pulses every 10° per revolution of the crankshaft, and 1 high and low output pulse every 30°. The ECM uses the NE signal for detecting the crankshaft position as well as for detecting the engine speed. It uses the missing teeth signal to determine the top-dead-center.

·

The cam position sensor uses a timing rotor installed on the front end of the intake camshaft sprocket of the left bank. Based on the timing rotor, the sensor outputs camshaft position signals (G2 signal) consisting of 3 (3 high output, 3 low output) pulses for every 2 revolutions of the crankshaft. The ECM compares the G2 and NE signals to detect the camshaft position and identify the cylinder.

·

The VVT sensors (intake and exhaust) use timing rotors installed on the intake and exhaust camshafts of each bank. Based on the timing rotors, the sensors output VVT position signals consisting of 3 (3 high output, 3 low output) pulses for every 2 revolutions of the crankshaft. The ECM compares these VVT position signals and the NE signal to detect the actual valve timing.

W131984C01
0.833,2.719 1.521,1.771 true 1.729,0.344 2.042,0.865 true 5.031,0.75 5.24,0.313 true 4.906,2.594 5.229,1.802 true 2.375,5.188 3.031,4.698 true 4.688,5.104 3.76,4.396 true 1.594,0.125 1.906,0.281 0.313,0.156 10 false *1 0.708,2.75 1.021,2.906 0.313,0.156 10 false *2 5.219,0.104 5.531,0.26 0.313,0.156 10 false *3 4.802,2.625 5.115,2.781 0.313,0.156 10 false *4 4.021,0.083 4.333,0.24 0.313,0.156 10 false *a 2.177,5.219 2.49,5.375 0.313,0.156 10 false *5 4.781,5.073 5.094,5.229 0.313,0.156 10 false *2
*1 Cam Position Sensor *2 Timing Rotor
*3 VVT Sensor (Intake) *4 VVT Sensor (Exhaust)
*5 Crank Position Sensor - -
*a Bank 1 - -


Wiring Diagram (Crank Position Sensor Circuit)
W128433E02
1.458,2.219 2.271,2.625 0.813,0.406 10 false Timing Rotor 3.063,1.719 4.073,2.438 1.01,0.719 10 false Crank Position Sensor 5.344,1.354 5.792,1.781 0.448,0.427 10 false ECM 4.563,0.917 4.948,1.115 0.385,0.198 10 false VCV2 4.656,1.24 4.969,1.438 0.313,0.198 10 false NE+ 4.688,1.573 4.948,1.74 0.26,0.167 10 false NE-

Sensor Output Waveforms
W128434E03
5.656,0.354 5.344,0.354 5.344,0.354 3.396,1.083 true 1.906,0.469 4.083,0.781 2.177,0.313 10 false VVT Sensor Signal Plate (720° CA) 5.75,0.281 6.667,0.979 0.917,0.698 10 false VVT Variable Timing Range 3.938,1.188 4.521,1.542 0.583,0.354 10 false 230° CA 5.271,1.188 5.823,1.531 0.552,0.344 10 false 140° CA 2.323,1.198 2.906,1.552 0.583,0.354 10 false 230° CA 1.677,1.302 1.938,1.698 0.26,0.396 10 false 40° CA 3.302,1.302 3.563,1.698 0.26,0.396 10 false 40° CA 4.938,1.292 5.198,1.688 0.26,0.396 10 false 40° CA 1.958,2.073 4.979,2.417 3.021,0.344 10 false Cam Position Sensor Signal Plate (720° CA) 0.031,1.323 0.844,1.667 0.813,0.344 10 false VVT Sensor* 0.094,2.854 0.708,3.958 0.615,1.104 10 false Cam Position Sensor 0.135,4.375 0.75,5.479 0.615,1.104 10 false Crank Position Sensor 1.865,2.917 2.125,3.313 0.26,0.396 10 false 60° CA 3.896,2.594 4.406,2.917 0.51,0.323 10 false 60° CA 3.146,3.063 3.719,3.375 0.573,0.313 10 false 180° CA 2.26,2.573 2.833,2.885 0.573,0.313 10 false 120° CA 5.281,2.594 5.854,2.906 0.573,0.313 10 false 180° CA 4.427,3.083 5,3.396 0.573,0.313 10 false 120° CA 2.063,3.865 2.635,4.177 0.573,0.313 10 false 360° CA 4.219,3.865 4.792,4.177 0.573,0.313 10 false 360° CA 1.667,4.115 2.24,4.427 0.573,0.313 10 false 10° CA 3.469,4.125 4.042,4.438 0.573,0.313 10 false 30° CA 1.073,5.438 5.917,5.781 4.844,0.344 10 false *: This is an example of an output waveform of the VVT sensor (bank 1, intake).



ii.

MRE Type Sensor

·

The MRE type sensor consists of an MRE, a magnet and a sensor.

·

The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to high or low. The ECM detects the crankshaft and camshaft positions based on this output voltage.

·

The differences between the MRE type sensor and the pick-up coil type sensor used on the conventional models are as follows:

-

The MRE type sensor outputs a constant level of high and low digital signals regardless of the engine speed. Therefore, the MRE type sensor can detect the positions of the crankshaft and camshaft at an early stage of cranking.

-

The pick-up coil type sensor outputs analog signals with levels that change with the engine speed.

MRE Type and Pick-up Coil Type Output Waveform Image Comparison
W128435E01
4.719,2.375 4.385,0.844 4.385,0.844 4.771,0.844 true 4.76,1.656 4.385,0.844 false 3.625,1.26 4.063,1.938 0.438,0.677 10 false Engine Speed 0.094,1.271 0.531,1.948 0.438,0.677 10 false Engine Speed 0.073,2.542 0.51,3.219 0.438,0.677 10 false Sensor Output 3.583,2.302 4.021,2.979 0.438,0.677 10 false Sensor Output 2.667,2.083 3.104,2.76 0.438,0.677 10 false Digital Output 4.875,0.771 5.688,1.125 0.813,0.354 10 false No Detection 6.635,2.042 7.073,2.719 0.438,0.677 10 false Analog Output 1.479,3.271 2.24,3.656 0.76,0.385 10 false MRE Type 4.896,3.26 6.031,3.635 1.135,0.375 10 false Pick-up Coil Type





d.

Accelerator Pedal Sensor Assembly

i.

The no-contact type accelerator pedal sensor assembly uses a Hall IC, which is mounted on the accelerator pedal arm.


ii.

A magnetic yoke is mounted at the base of the accelerator pedal arm. This yoke rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes that occur in the magnetic flux into electrical signals, and outputs them in the form of accelerator pedal position signals to the ECM.


iii.

The Hall IC contains two circuits, one for the main signal, and the other for the sub signal. It converts the accelerator pedal position (angle) into electric signals that have differing characteristics and outputs them to the ECM.

W132291C01
2.229,1.927 3.073,1.625 true 3.844,1.583 4.854,1.021 true 4.375,2.26 5.198,1.969 true 2.031,1.896 2.344,2.052 0.313,0.156 10 false *1 4.906,0.906 5.219,1.063 0.313,0.156 10 false *2 5.229,1.875 5.542,2.031 0.313,0.156 10 false *3
*1 Hall IC *2 Magnetic Yoke
*3 Accelerator Pedal Arm - -


W132962E04
1.188,1.323 1.188,0.823 1.188,0.823 0.917,0.823 true 1.271,1.563 1.521,0.302 1.521,0.302 1.844,0.302 true 1.188,2.375 1.188,2.771 1.188,2.771 0.917,2.771 true 1.271,2.406 2.104,3.208 2.104,3.208 2.604,3.208 true 0.74,1.625 0.073,0.26 0.073,0.26 0.396,0.26 true 0.26,3.083 1.958,3.76 1.698,0.677 10 false Accelerator Pedal Sensor Assembly 0.406,0.729 0.938,1.073 0.531,0.344 10 false Magnet 1.885,0.229 2.521,0.531 0.635,0.302 10 false Hall IC 2.073,0.938 2.438,1.135 0.365,0.198 10 false VPA 2.073,1.25 2.406,1.458 0.333,0.208 10 false EPA 1.979,1.552 2.417,1.75 0.438,0.198 10 false VCPA 2,1.792 2.438,1.99 0.438,0.198 10 false VPA2 2,2.063 2.438,2.26 0.438,0.198 10 false EPA2 1.99,2.365 2.427,2.563 0.438,0.198 10 false VCP2 0.396,2.677 0.927,3.021 0.531,0.344 10 false Magnet 2.646,3.167 3.281,3.469 0.635,0.302 10 false Hall IC 2.625,1.719 3.01,2.115 0.385,0.396 10 false ECM 3.948,0.938 4.156,1.167 0.208,0.229 10 false V 4.021,1.156 4.229,1.385 0.208,0.229 10 false 5 4.031,2.302 4.24,2.531 0.208,0.229 10 false 0 3.427,1.552 3.948,2.323 0.521,0.771 10 false Output Voltage 4.031,2.667 4.521,3.417 0.49,0.75 10 false Fully Closed 4.802,2.542 6,3.365 1.198,0.823 10 false Accelerator Pedal Position (Angle) 6.313,2.667 6.802,3.417 0.49,0.75 10 false Fully Open 4.76,1.604 5.177,1.802 0.417,0.198 10 false VPA2 5.479,1.969 5.896,2.167 0.417,0.198 10 false VPA 0.417,0.188 1.438,0.521 1.021,0.333 10 false Magnetic Yoke



e.

Throttle Position Sensor

i.

The non-contact type throttle position sensor uses a Hall IC, which is mounted on the throttle body.


ii.

The Hall IC is surrounded by a magnetic yoke. The Hall IC converts the changes that occur in the magnetic flux into electrical signals, and outputs them in the form of throttle valve position signals to the ECM.


iii.

The Hall IC contains circuits for the main and sub signals. The Hall IC converts the throttle valve opening angle into two electrical signals that have differing characteristics and outputs them to the ECM.

W133026C01
5.208,1.833 5.677,1.271 true 5.583,2.958 5.177,2.198 true 5.854,2.125 5.208,2.01 true 5.698,1.177 6.01,1.333 0.313,0.156 10 false *1 5.938,2.042 6.25,2.198 0.313,0.156 10 false *2 3.74,0.583 4.052,0.74 0.313,0.156 10 false *a 5.635,2.917 5.948,3.073 0.313,0.156 10 false *1
*1 Magnet *2 Hall IC
*a Cross Section - -


W132963E01
1.281,1.365 1.51,0.865 1.51,0.865 1.115,0.865 true 1.344,1.594 1.948,0.208 1.948,0.208 2.26,0.208 true 1.333,2.406 1.542,2.76 1.542,2.76 1.125,2.76 true 1.365,2.135 2.156,3.26 2.156,3.26 2.469,3.26 true 0.813,1.625 0.073,0.333 0.073,0.333 0.333,0.333 true 0.469,3.094 2,3.604 1.531,0.51 10 false Throttle Position Sensor 0.563,0.76 1.313,1.052 0.75,0.292 10 false Magnet 2.302,0.135 2.917,0.417 0.615,0.281 10 false Hall IC 0.594,2.667 1.313,2.979 0.719,0.313 10 false Magnet 2.542,3.177 3.156,3.458 0.615,0.281 10 false Hall IC 2.125,1.25 2.5,1.448 0.375,0.198 10 false VTA1 2.125,1.563 2.5,1.76 0.375,0.198 10 false ETA 2.073,1.865 2.51,2.063 0.438,0.198 10 false VCTA 2.073,2.156 2.51,2.354 0.438,0.198 10 false VTA2 2.708,1.802 3.083,2.177 0.375,0.375 10 false ECM 3.469,1.656 4.031,2.448 0.563,0.792 10 false Output Voltage 4.042,1.042 4.198,1.24 0.156,0.198 10 false V 4.094,1.25 4.25,1.448 0.156,0.198 10 false 5 4.094,2.323 4.25,2.521 0.156,0.198 10 false 0 4.021,2.646 4.719,3.75 0.698,1.104 10 false Throttle Valve Fully Closed 6.156,2.677 6.854,3.781 0.698,1.104 10 false Throttle Valve Fully Open 4.958,2.5 5.948,3.052 0.99,0.552 10 false Throttle Valve Opening Angle 6.406,2.458 6.865,2.656 0.458,0.198 10 false 90° 5.323,1.948 5.698,2.146 0.375,0.198 10 false VTA1 4.531,1.427 4.969,1.625 0.438,0.198 10 false VTA2 0.385,0.25 1.417,0.604 1.031,0.354 10 false Magnetic Yoke



f.

Knock Control Sensor (Flat Type)

i.

General

In the conventional type knock control sensor (resonant type), a vibration plate, which has the same resonance point as the knocking frequency of the engine, is built in and can detect the vibration in this frequency band.

On the other hand, a flat type knock control sensor (non-resonant type) has the ability to detect vibration in a wider frequency band from approximately 6 kHz to 15 kHz, and has the following features:

-

The engine knocking frequency will change slightly depending on the engine speed. The flat type knock control sensor can detect vibration even when the engine knocking frequency is changed. Thus the vibration detection ability is increased compared to the conventional type knock control sensor, and a more precise ignition timing control is possible.

Characteristic of Knock Control Sensor
W128426E05
1.542,0.427 4.417,0.792 2.875,0.365 10 false : Conventional type 1.552,0.833 3.969,1.24 2.417,0.406 10 false : Flat type 4.74,2.854 5.042,3.083 0.302,0.229 10 false (Hz) 2.094,1.396 2.313,1.615 0.219,0.219 10 false (V) 1.75,2.031 2.25,2.448 0.5,0.417 10 false Voltage 3.24,2.865 3.906,3.188 0.667,0.323 10 false Frequency 5.021,1.479 6.302,2.208 1.281,0.729 10 false A: Detection band of conventional type 5.052,2.229 6.365,2.917 1.313,0.688 10 false B: Detection band of flat type 3.802,2.375 3.969,2.563 0.167,0.188 10 false B 3.75,1.542 3.917,1.729 0.167,0.188 10 false A




ii.

Construction

·

The flat type knock control sensor is installed on the engine through the stud bolt installed on the cylinder block. For this reason, a hole for the stud bolt is running through in the center of the sensor.

·

Inside of the sensor, a steel weight is located on the upper portion and a piezoelectric element is located under the weight through the insulator.

·

The open/short circuit detection resistor is integrated.

W128427C01
1.188,1.354 0.708,1.01 true 1.167,1.458 0.667,1.281 true 1.146,1.542 0.781,1.74 true 2.385,1.51 2.438,0.781 true 5.448,1.292 6.146,0.885 true 5.5,1.333 6.219,1.531 true 0.625,0.396 0.927,0.667 0.302,0.271 12 false *A: 4.271,0.375 4.573,0.646 0.302,0.271 12 false *B: 0.604,1.688 0.865,1.927 0.26,0.24 11 false *3 0.49,1.156 0.75,1.396 0.26,0.24 11 false *2 0.531,0.875 0.792,1.115 0.26,0.24 11 false *1 2.375,0.604 2.635,0.844 0.26,0.24 11 false *4 6.177,0.76 6.438,1 0.26,0.24 11 false *3 6.25,1.479 6.51,1.719 0.26,0.24 11 false *5
*A Flat Type Knock Control Sensor (Non-resonant Type) *B Conventional Type Knock Control Sensor (Resonant Type)
*1 Steel Weight *2 Insulator
*3 Piezoelectric Element *4 Open/Short Circuit Detection Resistor
*5 Vibration Plate - -




iii.

Operation

The knocking vibration is transmitted to the steel weight and its inertia applies pressure to the piezoelectric element. This action generates electromotive force.

W128428C01
3.135,1.375 2.615,0.969 true 3.229,1.49 2.583,1.427 true 3.156,1.625 2.656,1.948 true 2.438,0.833 2.677,1.063 0.24,0.229 10 false *1 2.49,1.896 2.729,2.125 0.24,0.229 10 false *2 2.417,1.323 2.656,1.552 0.24,0.229 10 false *a
*1 Steel Weight *2 Piezoelectric Element
*a Inertia - -




iv.

Open/Short Circuit Detection Resistor

·

While the engine switch is on (IG), the open/short circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at the terminal KNK1 of engine constant.

·

An Integrated Circuit (IC) in the ECM is always monitoring the voltage of the terminal KNK1. If the open/short circuit occurs between the knock control sensor and the ECM, the voltage of the terminal KNK1 changes and the ECM detects the open/short circuit and stores Diagnostic Trouble Code (DTC).

W128429E05
0.844,0.854 0.271,0.854 0.271,0.854 1.094,2.271 true 1.906,2.281 2.396,3.188 2.396,3.188 2.573,3.188 true 0.896,0.802 2.292,1.146 1.396,0.344 10 false Piezoelectric Element 0.865,1.375 3.604,1.708 2.74,0.333 10 false Knock Control Sensor (Bank 1, Sensor 1) 2.625,3.115 3.833,3.75 1.208,0.635 10 false Open/Short Circuit Detection Resistor 2.01,2.208 2.521,2.552 0.51,0.344 10 false 200 kΩ 5.135,1.042 5.542,1.375 0.406,0.333 10 false ECM 4.375,1.146 4.656,1.5 0.281,0.354 10 false 5 V 4.531,1.688 5.042,1.906 0.51,0.219 10 false 220 kΩ 6.073,1.979 6.24,2.313 0.167,0.333 10 false IC 3.75,2.615 4.177,2.802 0.427,0.188 10 false EKNK 3.771,1.781 4.156,1.969 0.385,0.188 10 false KNK1

HINT:

These knock control sensors are mounted in specific directions at specific angles. To prevent the right and left bank wiring connectors from being interchanged, be sure to install each sensor in its prescribed direction. For details, refer to the Repair Manual.





g.

Air Fuel Ratio Sensor and Oxygen Sensor

i.

General

·

The oxygen sensor and the air fuel ratio sensor differ in output characteristics.

·

The output voltage of the oxygen sensor changes in accordance with the oxygen concentration in the exhaust gas. The ECM uses this output voltage to determine whether the present air-fuel ratio is richer or leaner than the stoichiometric air-fuel ratio.

·

Approximately 0.4 V is constantly applied to the air fuel ratio sensor, which outputs an amperage that varies in accordance with the oxygen concentration in the exhaust gas. The ECM uses this output voltage to determine whether the present air-fuel ratio is richer or leaner than the stoichiometric air-fuel ratio. The air fuel ratio sensor data is read out by the Techstream.

W128430E08
2.396,1.5 2.76,1.823 0.365,0.323 10 false ECM 5.813,1.521 6.177,1.844 0.365,0.323 10 false ECM 0.406,1.396 0.885,2.552 0.479,1.156 10 false Air Fuel Ratio Sensor 1.74,0.813 2.104,0.979 0.365,0.167 10 false A1A+ 1.667,1 2.104,1.344 0.438,0.344 10 false (3.3 V) 1.771,2.031 2.115,2.188 0.344,0.156 10 false A1A- 1.573,2.219 2.104,2.438 0.531,0.219 10 false (2.9 V) 1.156,2.604 2.875,3.25 1.719,0.646 10 false Air Fuel Ratio Sensor Circuit (Bank 1, Sensor 1) 0.573,4.667 2.177,5.813 1.604,1.146 10 false Air Fuel Ratio Sensor Data Displayed on Global TechStream (GTS) 5.073,2.031 5.5,2.198 0.427,0.167 10 false EX1B 5.135,0.823 5.5,0.979 0.365,0.156 10 false OX1B 4.563,1.01 5.521,1.344 0.958,0.333 10 false (0.1 V to 1.0 V) 4.927,3.292 6.26,3.615 1.333,0.323 10 false : Air fuel ratio sensor 4.948,3.646 6.448,4 1.5,0.354 10 false : Oxygen sensor 3.792,1.375 4.313,2.531 0.521,1.156 10 false Oxygen Sensor 4.677,2.552 6.333,3.26 1.656,0.708 10 false Oxygen Sensor Circuit (Bank 1, Sensor 2) 1.896,4.042 2.344,4.396 0.448,0.354 10 false 4.2 (V) 2.063,5.813 2.333,5.99 0.271,0.177 10 false 2.2 4.865,5.813 5.104,6.01 0.24,0.198 10 false 0.1 4.854,4.042 5.302,4.385 0.448,0.344 10 false 1.0 (V) 2.438,6.104 2.729,6.438 0.292,0.333 10 false Rich 4.531,6.104 4.927,6.375 0.396,0.271 10 false Lean 3.135,6.115 4.063,6.74 0.927,0.625 10 false Stoichiometric Air-fuel Ratio 4.917,4.677 5.938,5.344 1.021,0.667 10 false Oxygen Sensor Output



ii.

Construction

·

The basic construction of the oxygen sensor and the air fuel ratio sensor is the same. However, they are divided into the cup type and the planar type, according to the different types of heater construction that are used.

·

The cup type sensor contains a sensor element that surrounds the heater.

·

The planar type sensor uses alumina, which excels in heat conductivity and insulation, to integrate a sensor element with the heater, thus improving the warm-up performance of the sensor.

W132295C01
2.604,2.156 2.438,1.563 true 2.542,2.25 2.188,1.802 true 2.625,2.552 2.094,3.188 true 2.604,3.438 2.688,3.021 true 2.854,3.49 2.729,2.646 true 3.115,3.375 2.875,3.01 true 2.896,1.75 2.76,2.167 true 5.406,3.333 5.667,3 true 5.573,1.625 5.667,2.052 true 5.375,1.729 5.552,2.073 true 5.854,2.885 6.094,3.344 true 3.188,2.469 2.781,2.573 true 5.99,2.063 6.354,1.604 true 0.865,0.448 1.177,0.604 0.313,0.156 10 false *A: 3.896,0.49 4.208,0.646 0.313,0.156 10 false *B: 2.313,1.323 2.625,1.479 0.313,0.156 10 false *1 2,1.615 2.313,1.771 0.313,0.156 10 false *2 1.958,3.219 2.271,3.375 0.313,0.156 10 false *3 2.521,3.479 2.833,3.635 0.313,0.156 10 false *4 3.135,3.406 3.448,3.563 0.313,0.156 10 false *5 6.302,1.427 6.615,1.583 0.313,0.156 10 false *6 2.823,3.531 3.135,3.688 0.313,0.156 10 false *3 2.854,1.563 3.167,1.719 0.313,0.156 10 false *2 5.302,3.417 5.615,3.573 0.313,0.156 10 false *4 5.469,1.438 5.781,1.594 0.313,0.156 10 false *3 5.24,1.573 5.552,1.729 0.313,0.156 10 false *3 6.135,3.375 6.448,3.531 0.313,0.156 10 false *5 3.219,2.365 3.427,2.615 0.208,0.25 10 false *6
*A Air Fuel Ratio Sensor (Planar Type) *B Oxygen Sensor (Cup Type)
*1 Dilation Layer *2 Alumina
*3 Platinum Electrode *4 Sensor Element (Zirconia)
*5 Heater *6 Atmosphere

The illustrations above are intended to show the differences in the basic construction between the cup type sensor and the planner type sensor, so the illustrated sensor shapes may differ from the actual ones.


Warm-up Specification
Sensor Type Planar Type Cup Type
Warm-up Time Approx. 10 sec. Approx. 30 sec.





Electronic Throttle Control System-intelligent (ETCS-i)


a.

General

i.

In the conventional throttle body, the throttle valve angle is determined invariably by the amount of accelerator pedal effort. In contrast, ETCS-i uses the ECM to calculate the optimal throttle valve angle that is appropriate for the respective driving condition and uses a throttle control motor to control the angle.


ii.

In case of an abnormal condition, this system transfers to the fail-safe mode.

System Diagram
W133028E02
4.573,0.969 4.698,0.26 4.698,0.26 4.948,0.26 true 5.458,3.844 5.844,3.844 true 0.104,1.823 2.76,2.25 2.656,0.427 10 false Intake Mass Air Flow Meter Sub-assembly 0.333,2.51 2.646,2.938 2.313,0.427 10 false Accelerator Pedal Sensor Assembly 0.74,3.198 2.208,3.583 1.469,0.385 10 false Crank Position Sensor 0.719,3.875 2.542,4.281 1.823,0.406 10 false Pattern Select Switch 0.781,4.563 2.25,4.958 1.469,0.396 10 false Cam Position Sensor 0.563,5.25 2.521,5.677 1.958,0.427 10 false Cruise Control Main Switch*1 0.969,5.948 2.552,6.344 1.583,0.396 10 false VVT Sensors 0.302,6.615 2.594,7.021 2.292,0.406 10 false Engine Coolant Temperature Sensor 3.438,3.938 3.854,4.344 0.417,0.406 10 false ECM 2.865,0.802 4.281,1.281 1.417,0.479 10 false Network Gateway ECU 2.646,1.365 3.49,1.698 0.844,0.333 10 false CAN (V Bus) 5.031,0.156 7.031,0.646 2,0.49 10 false CAN (Movement Control Bus) 5.354,0.813 6.677,1.25 1.323,0.438 10 false Skid Control ECU 5.198,1.594 6.844,2.042 1.646,0.448 10 false Distance Control ECU*2 4.75,2.365 6.865,2.802 2.115,0.438 10 false Millimeter Wave Radar Sensor*2 4.563,3.292 5.615,3.604 1.052,0.313 10 false Throttle Body 4.583,3.75 5.458,4.146 0.875,0.396 10 false Throttle Valve 5.115,4.271 6.583,4.635 1.469,0.365 10 false Throttle Control Motor 5.042,4.698 6.625,5.083 1.583,0.385 10 false Throttle Position Sensor 4.604,5.698 6.896,6.146 2.292,0.448 10 false No. 1 to 8 Ignition Coils (with Igniter) 4.635,6.604 6.833,7.031 2.198,0.427 10 false No. 1 to 8 Fuel Injector Assemblies 0.115,7.167 2.563,7.479 2.448,0.313 10 false *1: Models with cruise control system 0.052,7.49 4.094,7.833 4.042,0.344 10 false *2: Models with dynamic radar cruise control system



b.

Control

i.

General

The ETCS-i consists of the following functions:

-

Normal Throttle Control (Non-linear Control)

-

Idle Speed Control (ISC)

-

Active Traction Control (A-TRC)*1

-

Vehicle Stability Control (VSC) Coordination Control*2

-

Crawl Control (CRAWL) Coordination Control*3

-

Cruise Control*4

-

Dynamic Radar Cruise Control*5

*1: Models with A-TRC

*2: Models with VSC

*3: Models with CRAWL

*4: Models with cruise control system

*5: Models with dynamic radar cruise control system





ii.

Normal Throttle Control (Non-linear Control)

1.

General

The throttle is controlled to an optimal throttle valve angle that is appropriate for the driving condition such as the amount of the accelerator pedal effort and the engine speed in order to achieve excellent throttle control and comfort in all operating ranges.

Conceptual Diagrams of Engine Control during Acceleration and Deceleration
W128439E01
5.042,0.25 5.938,0.594 0.896,0.344 10 false : With control 0.438,1.146 1.354,1.833 0.917,0.688 10 false Vehicle's Longitudinal G 0.438,2.156 1.375,2.51 0.938,0.354 10 false Ignition Timing 0.49,2.885 1.417,3.604 0.927,0.719 10 false Throttle Valve Opening Angle 0.479,3.875 1.604,4.563 1.125,0.688 10 false Accelerator Pedal Depressed Angle 5.042,0.625 6.083,0.969 1.042,0.344 10 false : Without control 4.823,4.406 5.167,4.719 0.344,0.313 10 false Time 1.656,4.26 1.781,4.521 0.125,0.26 10 false 0 1.646,3.344 1.771,3.604 0.125,0.26 10 false 0 1.646,2.448 1.771,2.708 0.125,0.26 10 false 0 1.646,1.604 1.771,1.865 0.125,0.26 10 false 0


2.

2nd Start Control

In situations in which low-μ (low friction) road surface conditions can be anticipated, such as when the vehicle is driving in the snow, the rate of throttle valve opening can be controlled to ensure vehicle stability while the vehicle is driving on the slippery surface. This is accomplished by turning on 2nd start control. Pressing the 2nd side of the pattern select switch activates this control. This control modifies the relationship and reaction of the throttle to the accelerator pedal, and assists the driver by reducing the engine output from that of a normal level.




iii.

Idle Speed Control

The ECM controls the throttle valve in order to constantly maintain an ideal idle speed.



iv.

A-TRC*

As part of the A-TRC, the throttle valve opening is reduced by a demand signal sent from the skid control ECU to the ECM. This demand signal will be sent if an excessive amount of slippage occurs at a drive wheel, thus ensuring vehicle stability and applying appropriate amount of power to the road.

*: Models with A-TRC




v.

VSC Coordination Control*

In order to bring the effectiveness of the VSC into full play, the throttle valve angle is regulated through a coordination control with the skid control ECU.

*: Models with VSC




vi.

CRAWL Coordination Control*

While the CRAWL is operating, the throttle valve is regulated through a coordination control with the skid control ECU.

*: Models with CRAWL




vii.

Cruise Control*

The ECM directly actuates the throttle valve for operation of the cruise control.

*: Models with cruise control system




viii.

Dynamic Radar Cruise Control*

The dynamic radar cruise control uses a millimeter wave radar sensor and the distance control ECU to determine the distance, direction, and relative speed to a vehicle ahead. Thus, the system can effect deceleration control, follow-up control, constant speed control, and acceleration control. To make these controls possible, the ECM controls the throttle valve.

*: Models with dynamic radar cruise control system






Dual Variable Valve Timing-intelligent (VVT-i) System


a.

General

i.

The Dual VVT-i system is designed to control the intake and exhaust camshafts within a range of 40° and 32° respectively (of crankshaft angle) to provide valve timing optimally suited to the engine operating conditions. This improves torque in all the speed ranges as well as increasing fuel economy, and reducing exhaust emissions.

W133029C01
3.792,0.479 4.104,0.635 0.313,0.156 10 false *1 3.813,0.729 4.125,0.885 0.313,0.156 10 false *2 3.823,0.979 4.135,1.135 0.313,0.156 10 false *3 3.823,1.229 4.135,1.385 0.313,0.156 10 false *4 3.802,1.479 4.115,1.635 0.313,0.156 10 false *5 3.802,1.729 4.115,1.885 0.313,0.156 10 false *6 3.802,2.167 4.115,2.323 0.313,0.156 10 false *7 4.875,2.281 5.188,2.438 0.313,0.156 10 false *8 3.802,2.948 4.115,3.104 0.313,0.156 10 false *9 3.771,3.313 4.24,3.469 0.469,0.156 10 false *10 3.771,3.615 4.24,3.771 0.469,0.156 10 false *11 3.781,3.969 4.25,4.125 0.469,0.156 10 false *12 5.792,2.969 6.26,3.125 0.469,0.156 10 false *13 5.781,3.385 6.25,3.542 0.469,0.156 10 false *14 5.792,3.833 6.26,3.99 0.469,0.156 10 false *15
*1 Camshaft Timing Oil Control Valve (Bank 2, Exhaust) *2 Camshaft Timing Oil Control Valve (Bank 2, Intake)
*3 VVT Sensor (Bank 2, Exhaust) *4 VVT Sensor (Bank 2, Intake)
*5 Cam Position Sensor *6 VVT Sensor (Bank 1, Intake)
*7 VVT Sensor (Bank 1, Exhaust) *8 ECM
*9 Crank Position Sensor *10 Camshaft Timing Oil Control Valve (Bank 1, Exhaust)
*11 Camshaft Timing Oil Control Valve (Bank 1, Intake) *12 Engine Coolant Temperature Sensor
*13 Intake Mass Air Flow Meter Sub-assembly *14 Throttle Position Sensor
*15 Vehicle Speed Signal - -



ii.

By using the engine speed, intake air mass, throttle position and engine coolant temperature, the ECM calculates the optimal valve timing for each driving condition and controls the camshaft timing oil control valves. In addition, the ECM uses signals from the intake and exhaust VVT sensors for each bank and the crank position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.

W133030E01
0.521,0.688 2.115,1 1.594,0.313 10 false Crank Position Sensor 0.563,1.208 2.146,1.521 1.583,0.313 10 false Cam Position Sensor 0.083,1.729 2.292,2.052 2.208,0.323 8 false Intake Mass Air Flow Meter Sub-assembly 0.448,2.25 2.208,2.615 1.76,0.365 10 false Throttle Position Sensor 0.531,2.771 2.24,3.115 1.708,0.344 10 false Vehicle Speed Signal 0.74,3.302 1.917,3.625 1.177,0.323 10 false VVT Sensors 0.083,3.823 2.281,4.146 2.198,0.323 10 false Engine Coolant Temperature Sensor 2.844,0.927 3.302,1.188 0.458,0.26 10 false ECM 3.667,1.271 4.938,1.583 1.271,0.313 10 false Target Valve Timing 4.281,2.344 4.979,2.688 0.698,0.344 10 false Feedback 3.927,2.781 4.938,3.104 1.01,0.323 10 false Correction 3.688,3.344 5,3.667 1.313,0.323 10 false Actual Valve Timing 5.292,1.5 6.052,2.198 0.76,0.698 10 true Duty Cycle Control 6.104,1.375 7.094,2.594 0.99,1.219 10 false Camshaft Timing Oil Control Valve



b.

Effectiveness of Dual VVT-i System

Condition Operation Timing/Position Objective Effect
During Idling
W133031E01
1.583,0.031 2.042,0.333 0.458,0.302 10 false TDC 0.885,1 1.115,1.344 0.229,0.344 10 false EX 2.385,1 2.688,1.302 0.302,0.302 10 false IN 1.573,1.802 2.042,2.115 0.469,0.313 10 false BDC

IN Most Retarded Position Eliminating overlap to reduce blow back to the intake side.
·

Stabilized idle speed

·

Better fuel economy


EX Most Advanced Position
In Low Speed Range with Light to Medium Load
W133032E01
0.823,1 1.094,1.354 0.271,0.354 10 false EX 2.385,0.906 2.656,1.26 0.271,0.354 10 false IN

IN Retarded Retarding the intake valve close timing and reducing pumping loss. Increasing overlap and internal EGR.
·

Better fuel economy

·

Improved emission control


EX Retarded
In Low to Medium Speed Range with Heavy Load
W133033E01
0.854,0.875 1.104,1.219 0.25,0.344 10 false EX 2.396,1 2.646,1.344 0.25,0.344 10 false IN

IN Advanced Advancing the intake valve close timing, reducing intake air blow back to the intake side, and improving volumetric efficiency. Improved torque in low to medium speed range
EX Advanced
In High Speed Range with Heavy Load
W133034E01
2.375,0.854 2.667,1.177 0.292,0.323 10 false IN 0.823,0.885 1.115,1.208 0.292,0.323 10 false EX

IN Retarded Retarding the intake valve close timing and improving volumetric efficiency using the inertia force of the intake air. Improved output
EX Advanced
·

Upon Starting

·

Stopping the Engine


W133031E02
0.823,0.99 1.125,1.271 0.302,0.281 10 false EX 2.438,1 2.74,1.281 0.302,0.281 10 false IN

IN Most Retarded Position Controlling valve timing and fixing it to the optimal timing for engine start. Improved startability
EX Most Advanced Position


c.

Construction

i.

Camshaft Timing Gear Assembly

·

The camshaft timing gear assembly consists of an outer housing that is driven by the timing chain sprocket, and a vane sub-assembly that is coupled to each camshaft.

·

The intake side uses a camshaft timing gear assembly with 3 vanes, and the exhaust side uses one with 4 vanes.

·

When the engine stops, the camshaft timing gear assembly (intake) is locked at the most retarded angle by its lock pin, and the camshaft timing gear assembly (exhaust) is locked at the most advanced angle. This ensures excellent engine startability.

·

The oil pressure sent from the advance or retard side passages of the intake and exhaust camshafts causes rotation of the vane sub-assembly relative to the timing chain sprocket, to vary the valve timing continuously.

·

An advance assist spring is provided on the camshaft timing gear assembly (exhaust). This helps to apply torque in the advanced angle direction so that the vane lock pin securely engages with the housing when the engine stops.

Intake Side
W133035C01
3.354,2.521 6.125,3.49 2.771,0.969 1.521,1.594 1.281,1.125 true 2.74,1.313 2.5,0.844 true 4.094,1.073 3.833,0.583 true 4.719,0.698 4.542,0.354 true 6.083,1.656 5.823,1.167 true 1.177,0.948 1.49,1.104 0.313,0.156 10 false *1 2.365,0.656 2.677,0.813 0.313,0.156 10 false *2 3.698,0.354 4.01,0.51 0.313,0.156 10 false *3 4.417,0.167 4.729,0.323 0.313,0.156 10 false *4 6.083,1.698 6.396,1.854 0.313,0.156 10 false *5 3.417,2.563 3.729,2.719 0.313,0.156 10 false *6 3.365,2.823 3.677,2.979 0.313,0.156 10 false *a 4.229,3.26 4.542,3.417 0.313,0.156 10 false *b 5.302,3.281 5.615,3.438 0.313,0.156 10 false *c
*1 Timing Rotor *2 Outer Housing
*3 Vane Sub-assembly (Coupled to Intake Camshaft) *4 Timing Chain Sprocket
*5 Intake Camshaft *6 Lock Pin
*a Oil Pressure *b In Operating
*c At a Stop - -


Exhaust Side
W133036C01
2.344,1.698 2.146,1.292 true 3.604,1.813 3.292,1.042 true 4.406,1.177 4.198,0.656 true 5.719,2.104 5.51,1.583 true 2.115,3.146 2.24,2.333 true 3.646,2.969 3.438,2.448 true 1.99,1.073 2.302,1.229 0.313,0.156 10 false *1 3.115,0.76 3.427,0.917 0.313,0.156 10 false *2 4.083,0.479 4.396,0.635 0.313,0.156 10 false *3 5.729,2.167 6.042,2.323 0.313,0.156 10 false *4 3.667,3.031 3.979,3.188 0.313,0.156 10 false *5 1.896,3.219 2.208,3.375 0.313,0.156 10 false *6
*1 Outer Housing *2 Lock Pin
*3 Timing Chain Sprocket *4 Exhaust Camshaft
*5 Vane Sub-assembly (Coupled on Exhaust Camshaft) *6 Advanced Assist Spring




ii.

Camshaft Timing Oil Control Valve

This camshaft timing oil control valve controls the spool valve using duty cycle control from the ECM. This allows hydraulic pressure to be applied to the camshaft timing gear assembly advance or retard side. When the engine is stopped, the camshaft timing oil control valve (intake) will move to the retard position, and the camshaft timing oil control valve (exhaust) will move to the advance position.

W128451C01
2.073,1.292 1.625,0.885 true 3.469,2.125 2.938,1.625 true 1.99,1.604 1.656,2.042 true 1.479,0.75 1.719,1.01 0.24,0.26 10 false *1 1.521,2.052 1.76,2.313 0.24,0.26 10 false *2 3.5,2.104 3.74,2.365 0.24,0.26 10 false *3 2.26,0.604 2.688,0.833 0.427,0.229 10 false *a (*e) 2.719,0.604 3.146,0.833 0.427,0.229 10 false *b (*e) 2.125,2.177 2.365,2.438 0.24,0.26 10 false *c 2.552,2.188 2.792,2.448 0.24,0.26 10 false *d 2.99,2.177 3.229,2.438 0.24,0.26 10 false *c
*1 Sleeve *2 Spring
*3 Spool Valve - -
*a To Camshaft Timing Gear Assembly (Advance Side) *b To Camshaft Timing Gear Assembly (Retard Side)
*c Drain *d Oil Pressure
*e On the exhaust side oil control valve, the advance and retard sides are reversed. - -





d.

Operation

i.

Advance

When the camshaft timing oil control valve is positioned as illustrated below by the advance signals from the ECM, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction.

Intake Side
W133037C01
0.521,1.302 0.375,0.781 true 0.604,2.417 0.802,2.01 true 5.156,2.448 4.646,2.333 true 0.281,0.583 0.594,0.74 0.313,0.156 10 false *1 6.333,1.063 6.646,1.219 0.313,0.156 10 false *2 0.51,2.469 0.823,2.625 0.313,0.156 10 false *a 4.458,2.25 4.771,2.406 0.313,0.156 10 false *b 5.094,2.563 5.406,2.719 0.313,0.156 10 false *c 5.344,2.573 5.656,2.729 0.313,0.156 10 false *d 5.823,2.01 6.135,2.167 0.313,0.156 10 false *3
*1 Vane Sub-assembly *2 ECM
*3 Camshaft Timing Oil Control Valve (Intake) - -
*a Rotation Direction *b Oil Pressure
*c In *d Drain


Exhaust Side
W133038C01
0.646,1.219 0.531,0.771 true 1.646,2.031 1.063,1.583 true 5.333,2.354 4.906,2.302 true 0.417,0.583 0.729,0.74 0.313,0.156 10 false *1 6.021,0.948 6.333,1.104 0.313,0.156 10 false *2 1.698,1.99 2.01,2.146 0.313,0.156 10 false *a 4.531,2.427 4.844,2.583 0.313,0.156 10 false *b 4.833,2.427 5.146,2.583 0.313,0.156 10 false *c 5.396,2.281 5.708,2.438 0.313,0.156 10 false *d 5.573,1.74 5.885,1.896 0.313,0.156 10 false *3
*1 Vane Sub-assembly *2 ECM
*3 Camshaft Timing Oil Control Valve (Exhaust) - -
*a Rotation Direction *b Drain
*c In *d Oil Pressure




ii.

Retard

When the camshaft timing oil control valve is positioned as illustrated below by the retard signals from the ECM, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction.

Intake Side
W133039C01
0.833,1.073 0.74,0.677 true 0.323,2 0.615,1.781 true 5.177,2.365 5.635,2.427 true 0.135,1.969 0.448,2.125 0.313,0.156 10 false *1 6.365,0.938 6.677,1.094 0.313,0.156 10 false *2 0.594,0.458 0.906,0.615 0.313,0.156 10 false *a 4.865,2.469 5.177,2.625 0.313,0.156 10 false *b 5.094,2.479 5.406,2.635 0.313,0.156 10 false *c 5.708,2.365 6.021,2.521 0.313,0.156 10 false *d 5.813,1.875 6.125,2.031 0.313,0.156 10 false *3
*1 Vane Sub-assembly *2 ECM
*3 Camshaft Timing Oil Control Valve (Intake) - -
*a Rotation Direction *b Drain
*c In *d Oil Pressure


Exhaust Side
W133040C01
0.417,2.344 0.656,2.031 true 0.938,1.333 1.115,0.76 true 4.896,2.24 4.479,2.198 true 0.271,2.365 0.583,2.521 0.313,0.156 10 false *1 6.021,0.948 6.333,1.104 0.313,0.156 10 false *2 1.042,0.573 1.354,0.729 0.313,0.156 10 false *a 4.302,2.115 4.615,2.271 0.313,0.156 10 false *b 4.833,2.406 5.146,2.563 0.313,0.156 10 false *c 5.104,2.406 5.417,2.563 0.313,0.156 10 false *d 5.573,1.708 5.885,1.865 0.313,0.156 10 false *3
*1 Vane Sub-assembly *2 ECM
*3 Camshaft Timing Oil Control Valve (Exhaust) - -
*a Rotation Direction *b Oil Pressure
*c In *d Drain




iii.

Hold

After reaching the target timing, the engine valve timing is maintained by keeping the camshaft timing oil control valve in the neutral position unless the engine operating conditions change.

This maintains the engine valve timing at the desired target position by preventing the engine oil from running out of the oil control valve.





Acoustic Control Induction System (ACIS)


a.

General

i.

The ACIS uses a bulkhead to divide the intake manifold into two stages, with an intake air control valve in the bulkhead being opened and closed to vary the effective length of the intake manifold in accordance with the engine speed and throttle valve opening angle. This increases the power output in all ranges from low to high speed.

System Diagram
W128456C01
2.313,0.74 2.917,1.333 true 2.99,0.344 3.375,0.771 true 3.052,1.979 3.188,2.208 true 3.156,3.24 2.906,3.573 true 3.802,0.552 4.146,0.333 true 2.833,0.229 3.104,0.458 0.271,0.229 10 false *1 2.146,0.594 2.417,0.823 0.271,0.229 10 false *2 3.177,2.208 3.448,2.438 0.271,0.229 10 false *3 2.781,3.573 3.052,3.802 0.271,0.229 10 false *4 5.177,1.875 5.448,2.104 0.271,0.229 10 false *5 4.146,0.229 4.417,0.458 0.271,0.229 10 false *6
*1 ACIS Actuator *2 Intake Air Control Valve
*3 Throttle Position Sensor *4 Crank Position Sensor
*5 ECM *6 VSV (for ACIS)




b.

Intake Air Control Valve and ACIS Actuator

i.

The intake air control valve and ACIS actuator are integrated with the intake manifold. This valve opens and closes to change the effective length of the intake manifold in 2 stages.

W133041C01
2.802,0.896 2.365,0.344 true 2.167,1.021 1.729,1.146 true 2.177,0.156 2.49,0.313 0.313,0.156 10 false *1 1.531,1.115 1.844,1.271 0.313,0.156 10 false *2 5.167,0.042 5.479,0.198 0.313,0.156 10 false *a
*1 Intake Air Control Valve *2 ACIS Actuator
*a Front - -




c.

Operation

i.

When Intake Control Valve Closes (VSV On)

The ECM activates the VSV so that the negative pressure acts on the diaphragm chamber of the actuator. This closes the control valve to match the longer pulsation cycle. As a result, the effective length of the intake manifold is lengthened and the intake efficiency in the low-to-medium engine speed range under heavy load and low-to-high engine speed range under low load is improved due to the dynamic effect of the intake air, thereby increasing the power output.

W131993E01
2.125,1.292 1.802,0.188 1.802,0.188 1.552,0.188 true 0.042,0.083 1.625,0.781 1.583,0.698 10 false Intake Air Control Valve (Closed) 1.073,3.115 3.208,3.51 2.135,0.396 10 false : Effective intake manifold length 4.229,1.031 4.677,1.354 0.448,0.323 10 false Wide 3.417,1.708 4.5,2.625 1.083,0.917 10 false Throttle Valve Opening Angle 4.094,2.635 4.573,2.927 0.479,0.292 10 false Narrow 4.656,2.844 5.188,3.177 0.531,0.333 10 false Low 6.729,2.844 7.146,3.167 0.417,0.323 10 false High 5.51,1.979 6.104,2.281 0.594,0.302 10 true VSV On 5.396,3.167 6.354,3.5 0.958,0.333 10 false Engine Speed



ii.

When Intake Control Valve Opens (VSV Off)

The ECM deactivates the VSV so that atmospheric air is led into the diaphragm chamber of the actuator. This opens the control valve to match the shorter pulsation cycle. When the control valve is open, the effective length of the intake manifold is shortened and peak intake efficiency is shifted. This benefits the high engine speed range under heavy load, thus providing greater output at high engine speeds.

W131994E01
2.167,1.219 1.552,0.125 1.552,0.125 1.208,0.125 true 0.031,0.021 1.219,0.719 1.188,0.698 10 false Intake Air Control Valve (Open) 1.094,3.125 3.219,3.469 2.125,0.344 10 false : Effective intake manifold length 4.219,0.979 4.615,1.281 0.396,0.302 10 false Wide 4.063,2.625 4.583,2.938 0.521,0.313 10 false Narrow 4.625,2.854 5.146,3.167 0.521,0.313 10 false Low 6.698,2.865 7.115,3.177 0.417,0.313 10 false High 5.479,3.135 6.427,3.479 0.948,0.344 10 false Engine Speed 3.458,1.677 4.427,2.542 0.969,0.865 10 false Throttle Valve Opening Angle 6.271,1.219 6.854,1.542 0.583,0.323 10 true VSV Off





Fuel Pump Control


a.

General

i.

In this vehicle, there are 2 types of fuel pump controls. The fuel pump is controlled to an optimum speed to match the engine operating conditions, and the fuel pump operation is stopped when the SRS airbags deploy.

·

The ECM transmits a fuel pump operation request signal to the fuel pump ECU that corresponds to the engine operating conditions. The fuel pump ECU receives this request signal and controls the speed of the fuel pump. As a result, under light engine loads, fuel pump speed is kept low to reduce electric power loss.

·

A fuel cut control is used to stop the fuel pump when any of the SRS airbags deploys. In this control, if an airbag deployment signal from the center airbag sensor assembly is detected by the ECM, the ECM will turn off the circuit opening relay. As a result, the power supply to the fuel pump ECU is stopped, causing the fuel pump to stop operating. After the fuel cut control has been activated, turning the ignition switch from off to on cancels the fuel cut control, and the engine can be restarted.

System Diagram
W133042E01
3.438,3.885 3.063,3.885 3.063,3.885 2.854,2.615 false 0.198,0.906 1.573,1.688 1.375,0.781 10 false Front Airbag Sensors (RH and LH) 0.198,2.177 1.573,2.958 1.375,0.781 10 false Rear Floor Side Airbag Sensors (RH and LH) 0.188,3.458 1.563,4.24 1.375,0.781 10 false Side Airbag Sensor (RH or LH) 0.219,4.74 1.594,5.521 1.375,0.781 10 false Rear Airbag Sensor (RH or LH) 2.031,1.563 2.604,3.74 0.573,2.177 10 false Center Airbag Sensor Assembly 3.448,1.917 3.948,2.698 0.5,0.781 10 false ECM 3.531,3.813 4.448,4.115 0.917,0.302 10 false CAN (V Bus) 4.167,2.615 4.927,3.74 0.76,1.125 10 false Fuel Pump Operation Request 4.25,0.719 5.229,1.208 0.979,0.49 10 false EFI Main Relay 5.781,0.448 6.823,0.781 1.042,0.333 10 false Battery 6.24,2.146 7.01,2.604 0.771,0.458 10 false Fuel Pump 5.021,2.302 5.781,3.302 0.76,1 10 false Fuel Pump Control ECU




b.

Fuel Pump Control ECU

i.

The fuel pump control ECU controls fuel pump speed by receiving a duty cycle signal (FPC terminal input) from the ECM, and control is performed steplessly.

W133043E01
2.771,1.719 2.771,0.656 2.771,0.656 3.042,0.656 false 1.844,1.531 2.281,1.896 0.438,0.365 10 false ECM 3.146,0.594 4.031,1.625 0.885,1.031 10 false Fuel Pump Operation Request 2.74,2.063 3.906,2.354 1.167,0.292 10 false Duty Cycle Signal 2.5,1.74 2.958,1.938 0.458,0.198 10 false FPC 4.135,1.625 4.979,2.75 0.844,1.125 10 false Fuel Pump Control ECU 5.49,1.281 6.542,1.719 1.052,0.438 10 false Fuel Pump




Air Injection Control


a.

General

i.

To ensure the proper warm-up performance of the Three-Way Catalytic converters (TWCs) after starting a cold engine, an air injection control is used.

·

This system is comprised of an air injection control driver, an air pump, and 2 air switching valves with the built-in air pressure sensors. The air switching valves provided on each bank are controlled independently by the ECM and the air injection control driver.

·

The ECM estimates the amount of air injected to the TWCs based on signals from the intake mass air flow meter sub-assembly in order to regulate the air injection time.

System Diagram
W133429C01
1.177,2.292 1.427,2.198 true 1.281,2.667 1.469,2.375 true 2.927,1.656 3.052,1.51 true 2.927,3.813 3.052,3.667 true 2.563,0.885 2.875,1.042 0.313,0.156 10 false *1 0.979,2.292 1.292,2.448 0.313,0.156 10 false *2 1.042,2.708 1.563,3.042 0.521,0.333 10 false *3 (*A) 2.104,6.104 2.677,6.323 0.573,0.219 10 false *4 (*A) 3.042,1.365 3.354,1.521 0.313,0.156 10 false *5 2.781,2.365 3.094,2.521 0.313,0.156 10 false *6 5.125,3.104 5.438,3.26 0.313,0.156 10 false *7 5.99,1.677 6.302,1.833 0.313,0.156 10 false *8 5.979,3.365 6.292,3.521 0.313,0.156 10 false *9 5.948,5.438 6.417,5.594 0.469,0.156 10 false *10 0.76,1.865 1.073,2.021 0.313,0.156 10 false *a 3.865,0.49 4.177,0.646 0.313,0.156 10 false *b 3.865,0.76 4.177,0.917 0.313,0.156 10 false *c 3.875,1.01 4.188,1.167 0.313,0.156 10 false *d 3.281,2.031 3.594,2.188 0.313,0.156 10 false *e 4.167,2.156 4.479,2.313 0.313,0.156 10 false *f 4.167,4.323 4.479,4.521 0.313,0.198 10 false *g 3.063,3.542 3.375,3.698 0.313,0.156 10 false *5 2.771,4.563 3.083,4.719 0.313,0.156 10 false *6 3.271,4.479 3.583,4.635 0.313,0.156 10 false *e
A Models with Air Injection Heater - -
*1 Air Injection Control Driver *2 Air Pump
*3 Heater *4 AI HTR Relay
*5 Air Pressure Sensor *6 Air Switching Valve
*7 ECM *8 Engine Coolant Temperature Sensor
*9 Intake Mass Air Flow Meter Sub-assembly *10 Intake Air Temperature Sensor
*a Air *b Pump Actuation Request
*c Valve Actuation Request *d Diagnosis Signal
*e To Exhaust Manifold *f Bank 1 (Left Bank)
*g Bank 2 (Right Bank) - -





b.

Construction and Operation

i.

Air Pump

·

Each air pump consists of a DC motor, an impeller and an air filter.

·

The air pump supplies air into an air injection control valve using its impeller.

·

The air filter is maintenance-free.

·

A heater is provided to prevent operation faults in cold conditions.*

*: Models with air injection heater

W133046C01
4.135,0.083 6.76,2.719 2.625,2.635 2.917,0.51 3.115,0.271 true 3.125,1.833 2.813,1.333 true 5.094,1.052 4.531,0.656 true 4.844,1.26 4.479,1.479 true 5.313,2.052 4.948,2.271 true 6.302,0.271 6.021,0.542 true 3.104,0.104 3.417,0.26 0.313,0.156 10 false *1 4.313,0.51 4.625,0.667 0.313,0.156 10 false *3 4.781,2.271 5.094,2.427 0.313,0.156 10 false *4 6.344,0.146 6.656,0.302 0.313,0.156 10 false *5 0.583,0.458 0.896,0.615 0.313,0.156 10 false *a 0.49,1.063 0.802,1.219 0.313,0.156 10 false *b 4.177,0.125 4.49,0.281 0.313,0.156 10 false *c 3.167,1.844 3.625,2.063 0.458,0.219 10 false *2 (*d) 4.25,1.5 4.708,1.719 0.458,0.219 10 false *2 (*d)
*1 Air Pump *2 Heater
*3 Impeller *4 DC Motor
*5 Air Filter - -
*a Air In *b Air Out
*c Cross Section *d Models with Air Injection Heater





ii.

Air Switching Valve

·

The air switching valve is operated by a solenoid coil to control air injection and prevent back-flow of exhaust gas. The opening timing of the valve is synchronized with the operation timing of the air pump.

·

An air pressure sensor is built into the corresponding air switching valve.

·

The structure and function of the air switching valves for bank 1 and bank 2 are basically the same.

W133047C01
3.542,0.156 7.021,2.635 3.479,2.479 1.698,0.417 1.427,0.198 true 5.208,0.594 4.885,0.333 true 5.156,1.448 4.438,1.052 true 6.156,0.573 5.542,0.948 true 1.229,0.052 1.542,0.208 0.313,0.156 10 false *1 4.667,0.188 4.979,0.344 0.313,0.156 10 false *2 4.26,0.938 4.573,1.094 0.313,0.156 10 false *3 6.208,0.5 6.521,0.656 0.313,0.156 10 false *4 2.615,0.49 2.927,0.646 0.313,0.156 10 false *a 0.667,2.365 0.979,2.521 0.313,0.156 10 false *b 3.594,0.198 3.906,0.354 0.313,0.156 10 false *c 6.646,1.344 6.958,1.5 0.313,0.156 10 false *a 3.771,1.531 4.083,1.688 0.313,0.156 10 false *b
*1 Air Switching Valve *2 Air Pressure Sensor
*3 Valve *4 Solenoid Coil
*a Air In *b Air Out
*c Cross Section - -




iii.

Air Pressure Sensor

·

The air pressure sensor consists of a semiconductor, which has a silicon chip that changes its electrical resistance when pressure is applied to it. The sensor converts the pressure into an electrical signal, and sends it to the ECM in an amplified form.

·

The structure and function of the air pressure sensors for bank 1 and bank 2 are basically the same.

W128469E01
1.708,2.063 1.51,2.052 1.51,2.052 1.51,1 true 0.948,0.958 0.625,0.281 0.625,0.281 1.021,0.281 true 1.052,0.219 1.813,0.531 0.76,0.313 10 false Sensor Unit 1.75,2.01 2.865,2.667 1.115,0.656 10 false Air Pressure of Electric Air Pump 3.25,1.063 3.74,1.833 0.49,0.771 10 false Output Voltage 3.792,0.49 4.031,0.688 0.24,0.198 10 false (V) 3.698,0.76 3.969,0.938 0.271,0.177 10 false 4.5 5.865,2.052 6.281,2.25 0.417,0.198 10 false (kPa) 4.417,2.167 5.656,2.781 1.24,0.615 10 false Air Pressure (Absolute Pressure) 3.698,1.51 3.969,1.698 0.271,0.188 10 false 0.5 4.25,2.042 4.458,2.24 0.208,0.198 10 false 45 5.563,2.042 5.802,2.26 0.24,0.219 10 false 150

·

The ECM detects operation of the air injection control based on signals from the air pressure sensor as follows:

(a)

When the air pump is on and the air switching valve is closed, the pressure is stable.

(b)

When the air pump is on and the air switching valve is open, the pressure drops slightly and becomes unstable because of exhaust pulses.

(c)

When the air pump is off and the air switching valve is closed, the pressure remains at atmospheric pressure.

(d)

When the air pump is off and the air switching valve is open, the pressure drops below atmospheric pressure and becomes unstable because of exhaust pulses.

W128470E03
0.292,0.448 1.042,0.802 0.75,0.354 10 false Example: 1 3.844,0.438 4.594,0.792 0.75,0.354 10 false Example: 2 0.292,3.01 1.042,3.365 0.75,0.354 10 false Example: 3 3.865,3.083 4.615,3.438 0.75,0.354 10 false Example: 4 0.26,0.948 0.844,1.323 0.583,0.375 10 false Pressure 3.792,0.927 4.375,1.302 0.583,0.375 10 false Pressure 0.302,3.479 0.885,3.854 0.583,0.375 10 false Pressure 3.833,3.49 4.417,3.865 0.583,0.375 10 false Pressure 0.823,2.042 0.938,2.281 0.115,0.24 10 false 0 4.365,2.042 4.479,2.281 0.115,0.24 10 false 0 0.823,4.583 0.938,4.823 0.115,0.24 10 false 0 4.365,4.615 4.479,4.854 0.115,0.24 10 false 0 0.073,2.198 0.917,2.958 0.844,0.76 10 false (Atmospheric Pressure) 0.063,4.781 0.906,5.542 0.844,0.76 10 false (Atmospheric Pressure) 3.594,2.24 4.438,3 0.844,0.76 10 false (Atmospheric Pressure) 3.583,4.813 4.427,5.573 0.844,0.76 10 false (Atmospheric Pressure) 2.74,2.052 3.052,2.385 0.313,0.333 10 false Time 6.271,2.042 6.583,2.375 0.313,0.333 10 false Time 6.271,4.604 6.583,4.938 0.313,0.333 10 false Time 2.75,4.604 3.063,4.938 0.313,0.333 10 false Time 0.927,2.354 2.74,2.646 1.813,0.292 10 false Air Pump: On 0.938,2.688 3.552,3.01 2.615,0.323 10 false Air Switching Valve: Closed 4.479,2.354 6.292,2.646 1.813,0.292 10 false Air Pump: On 4.469,2.688 7.083,3.01 2.615,0.323 10 false Air Switching Valve: Open 0.927,4.875 2.74,5.167 1.813,0.292 10 false Air Pump: Off 0.938,5.198 3.552,5.521 2.615,0.323 10 false Air Switching Valve: Closed 4.479,4.875 6.292,5.167 1.813,0.292 10 false Air Pump: Off 4.469,5.177 7.083,5.5 2.615,0.323 10 false Air Switching Valve: Open




iv.

Air Injection Control Driver

·

A semiconductor type air injection control driver is used. Activated by the ECM, this driver actuates the air pump and the air switching valve.

·

The air injection control driver also detects failures in the input and output circuits of the air injection driver and transmits the failure status to the ECM via duty cycle signals.

W128471E01
1.854,1.927 1.854,1.313 1.854,1.313 2.01,1.313 false 1.865,0.917 1.865,0.25 1.865,0.25 2.021,0.25 false 2.188,2.656 2.188,3.49 2.188,3.49 2.385,3.49 true 1.135,1.823 1.479,2.167 0.344,0.344 10 false ECM 2.073,0.167 3.271,0.896 1.198,0.729 10 false Air Pump Actuation Request 1.792,0.958 2.135,1.177 0.344,0.219 10 false AIRP 3.135,0.969 3.375,1.177 0.24,0.208 10 false SIP 2.052,1.229 3.26,1.896 1.208,0.667 10 false Air Switching Valve Actuation Request 1.792,1.938 2.135,2.146 0.344,0.208 10 false AIRV 3.135,1.958 3.375,2.177 0.24,0.219 10 false SIV 2.427,3.406 3.552,3.771 1.125,0.365 10 false Duty Cycle Signal 1.813,2.99 2.115,3.198 0.302,0.208 10 false AIDI 3.24,2.958 3.406,3.177 0.167,0.219 10 false DI 3.5,1.688 4.292,2.344 0.792,0.656 10 false Air Injection Control Drive 4.417,1.198 4.656,1.385 0.24,0.188 10 false VP 4.427,2.323 4.688,2.5 0.26,0.177 10 false VV 5.073,1.521 5.677,1.865 0.604,0.344 10 false Air Pump 4.99,3.01 5.813,3.698 0.823,0.688 10 false Air Switching Valve

DI Terminal Output
Condition AIRP AIRV Output (Duty Cycle Signal)
Open circuit in line between AIDI and DI terminals. - -
W128239E01
0.469,1.188 0.813,1.604 0.344,0.417 10 false GND

Failure in line between ECM terminals and air injection control driver. - -
W128244E02
0.458,1.208 0.823,1.583 0.365,0.375 10 false GND

Output failure at air injection control driver. (Failure in air pump actuation circuit) - -
W128240E01
0.458,1.26 0.802,1.688 0.344,0.427 10 false GND 1.427,0.625 2.031,0.917 0.604,0.292 10 false 200 ms 2.667,0.781 3.302,1.115 0.635,0.333 10 false Duty 20%

Output failure at air injection control driver. (Failure in air switching valve actuation circuit) - -
W128241E01
0.458,1.24 0.813,1.625 0.354,0.385 10 false GND 2.688,0.771 3.333,1.208 0.646,0.438 10 false Duty 40%

Overheat failure of air injection control driver. - -
W128242E01
0.417,1.24 0.792,1.583 0.375,0.344 10 false GND 2.635,0.771 3.292,1.125 0.656,0.354 10 false Duty 60%

Normal On On
W128243E01
0.448,1.25 0.813,1.635 0.365,0.385 10 false GND 2.677,0.802 3.313,1.219 0.635,0.417 10 false Duty 80%

Off Off
W128244E02
0.458,1.208 0.823,1.583 0.365,0.375 10 false GND

On Off
Off On





Starter Control (Cranking Hold Function)


a.

General

i.

Once the engine switch is pressed, this function operates the starter until the engine starts, provided that the brake pedal is depressed. This prevents application of the starter for an inadequate length of time and also prevents the engine from being cranked after it has started.


ii.

When the ECM detects a start signal from the main body ECU, this system monitors the engine speed (NE signal) and continues to operate the starter until it has determined that the engine has started. Furthermore, even if the ECM detects a start signal from the main body ECU, this system will not operate the starter if the ECM has determined that the engine has already started.

System Diagram
W133044E01
0.469,1.26 1.396,1.615 0.927,0.354 10 false Engine Switch 0.49,2.698 1.354,3.052 0.865,0.354 10 false Brake Pedal 2.333,1.26 3,2.135 0.667,0.875 10 false Main Body ECU 3.167,0.521 3.781,0.719 0.615,0.198 10 false STSW 3.156,0.885 3.771,1.083 0.615,0.198 10 false ACCR 3.146,1.229 3.76,1.427 0.615,0.198 10 false STR2 3.146,1.563 3.76,1.76 0.615,0.198 10 false IG2D 5.594,0.5 6.104,0.708 0.51,0.208 10 false STSW 5.615,0.844 6.094,1.073 0.479,0.229 10 false ACCR 5.646,1.177 6.156,1.385 0.51,0.208 10 false STAR 4.5,1.427 5.323,1.667 0.823,0.24 9 false From Battery 3.823,2.052 4.594,2.438 0.771,0.385 10 false IG2 Relay 3.771,3.01 4.844,3.365 1.073,0.354 10 false Starter Cut Relay 3.781,3.75 5.125,4.385 1.344,0.635 10 false Park/Neutral Position Switch Assembly 2.854,3.208 3.667,3.625 0.813,0.417 10 false ACC Relay 6.417,3.521 6.875,3.906 0.458,0.385 10 false ECM 5.74,4.167 6.198,4.365 0.458,0.198 10 false STA 3.979,4.677 4.885,5.031 0.906,0.354 10 false Starter Relay 1.156,6.229 1.677,6.563 0.521,0.333 10 false Battery 2.177,6.25 2.781,6.615 0.604,0.365 10 false Starter 3.833,6.125 5.625,6.74 1.792,0.615 10 false Engine Coolant Temperature Sensor 4.021,6.969 5.583,7.302 1.563,0.333 10 false Crank Position Sensor



b.

Operation

i.

As indicated in the timing chart below, when the ECM detects an STSW signal (start signal) from the main body ECU, it outputs a STAR signal (starter relay drive signal) through the starter cut relay to the starter relay and actuates the starter. The ECM also outputs an ACCR signal (ACC cut request signal) to the main body ECU. Thus, the main body ECU will not energize the ACC relay.


ii.

After the starter operates and the engine speed becomes higher than approximately 500 rpm, the ECM determines that the engine has started and stops the output of the STAR signal to the starter relay and the output of ACCR signal to the main body ECU. Thus, the starter operation stops and the main body ECU energizes the ACC relay.


iii.

If the engine has any failure and does not start, the starter operates as long as its maximum continuous operation time and stops automatically. The maximum continuous operation time is approximately 2 seconds through 25 seconds depending on the water temperature condition. When the water temperature is extremely low, the time is approximately 25 seconds and when the engine is warmed up sufficiently, the time is approximately 2 seconds.


iv.

This system cuts off the current that powers the accessories while the engine is cranking to prevent the accessory illumination from operating intermittently due to the unstable voltage that is associated with the cranking of the engine.


v.

This system has following protection features:

·

While the engine is running normally, the starter does not operate.

·

Even if the driver keeps pressing the engine switch, the ECM stops the output of the STAR and ACCR signals when the engine speed becomes higher than 1200 rpm. Thus, the starter operation stops and the main body ECU energizes the ACC relay.

·

In case the driver keeps pressing the engine switch and the engine does not start, the ECM stops the output of the STAR and ACCR signals after 30 seconds have elapsed. Thus, the starter operation stops and the main body ECU energizes the ACC relay.

·

In case the ECM cannot detect an engine speed signal while the starter is operating, it will immediately stop the output of the STAR and ACCR signals. Thus, the starter operation stops and the main body ECU energizes the ACC relay.

Timing Chart
W133045E01
0.219,0.385 1.49,0.771 1.271,0.385 10 false Start Signal (STSW) 1.833,0.208 2.063,0.479 0.229,0.271 10 false On 1.844,0.625 2.094,0.927 0.25,0.302 10 false Off 1.833,0.906 2.063,1.177 0.229,0.271 10 false On 1.823,1.302 2.073,1.604 0.25,0.302 10 false Off 1.552,1.729 2.042,2 0.49,0.271 10 false On (Off) 1.552,2.083 2.052,2.375 0.5,0.292 10 false Off (On) 0.073,1.01 1.625,1.656 1.552,0.646 10 false Starter Relay Drive Signal (STAR) 0.083,1.833 1.458,2.719 1.375,0.885 10 false ACC Relay (ACC Cut Request Signal: ACCR) 0.021,3 1.781,3.458 1.76,0.458 10 false Engine Speed (NE Signal) 5.594,2.302 7.104,2.969 1.51,0.667 10 false Successful Starting of Engine 5.594,3.052 7.156,3.385 1.563,0.333 10 false Failed Starting of Engine 2.188,3.75 5.552,4.604 3.365,0.854 10 false ECM determines that the engine has started successfully when the engine speed is approximately 500 rpm. 3.188,1.219 4.302,2.104 1.115,0.885 10 false Cranking Limit Approx. 2 to 25 sec.





Diagnosis


a.

When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section. Furthermore, the MIL in the combination meter illuminates or blinks to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Code (DTC) of the malfunctions. The DTC can be accessed by using the Global TechStream (GTS).


c.

For details, refer to the Repair Manual.

HINT:

To clear the DTC that is stored in the ECM, use the Global TechStream (GTS), disconnect the battery terminal or remove the EFI MAIN fuse and ETCS fuse for 1 minute or longer.




Fail-safe


a.

When a malfunction is detected at any of the sensors, there is a possibility of an engine or other malfunction occurring if the ECM were to continue to control the engine control system in the normal way. To prevent such a problem, the fail-safe function of the ECM either relies on the data stored in memory to allow the engine control system to continue operating, or stops the engine if a hazard is anticipated. For details, refer to the Repair Manual.