Home › General › ENGINE › 1VD-FTV ENGINE
NM2660E _V1 General _054359 ENGINE _0267381 1VD-FTV ENGINE UN GENERAL/CONTROL/DETAILS F

ENGINE  1VD-FTV ENGINE  GENERAL/CONTROL/DETAILS  ENGINE CONTROL SYSTEM  


General


a.

The engine control system of the 1VD-FTV engine has the following systems:

System Outline EURO 5 Except EURO 5

○: Applicable

-: Not applicable

*1: Models with dual fuel tank

*2: Models compliant with EURO 2, EURO 3 and EURO 4 emission regulations

*3: Models with entry and start system

Fuel Injection Volume Control Based on the signals received from the sensors, the ECM determines the fuel injection volume in accordance with the engine condition. ○ ○
Fuel Injection Timing Control Based on the signals received from the sensors, the ECM determines the fuel injection timing in accordance with the engine condition. ○ ○
During Starting Control To facilitate startability, the ECM optimally controls the injection volume and injection timing during starting. ○ ○
Idle Speed Control The ECM determines the idle speed in accordance with the engine condition, and controls the fuel injection volume in order to maintain the target idle speed. ○ ○
Fuel Pressure Control Based on the signals received from the sensors, the ECM controls fuel pressure using the Suction Control Valve (SCV) and fuel pressure discharge valve in accordance with engine operating conditions. ○ -
Based on the signals received from the sensors, the ECM controls fuel pressure using the (Suction Control Valve) SCV in accordance with the engine conditions. - ○
Pilot Injection Control Based on the signals received from the sensors, the ECM determines pilot injection volume/timing, and interval (between pilot injection and main injection) in accordance with the engine condition. ○ ○
Glow Plug Control Controls the length of time when the current is applied to the glow plugs in accordance with the engine coolant temperature. ○ ○
Throttle Control
·

Based on the signals received from the various sensors, the ECM determines throttle valve position in accordance with the engine conditions.

·

Fully closes the throttle valve in order to reduce vibration when the engine is stopped.


○ ○
Turbocharger Control Based on the signals received from the sensors, the ECM controls the actuator in accordance with the engine conditions. ○ -
Based on the signals received from the sensors, the ECM controls the actuator via the turbo motor driver in accordance with the engine conditions. - ○
Fuel Pump Control*1 Based on the signals from the sensors, the ECM operates the fuel pump to optimally control the transfer of the fuel from the fuel sub tank sub-assembly to the fuel tank sub-assembly. - ○
EGR Control Based on the signals received from the sensors, the ECM determines the EGR volume via the EGR valve and throttle valve in accordance with the engine conditions. ○ ○*2
Engine Mounting Control When the engine speed and the vehicle speed are low, this control utilizes vacuum to soften the engine mounting characteristics in order to restrain the engine vibration. ○ ○
Oil Maintenance Management When the ECM determines engine oil deterioration, the engine oil change reminder light turns on to inform the driver. ○ -
Starter Control (Cranking Hold Function)*3 Once the engine switch is pushed, this control continues to operate the starter until the engine is started. ○ ○
Air Conditioner Cut-off Control By controlling the air conditioner compressor on or off in accordance with the engine conditions, driveability is maintained. ○ ○
Catalyst Support Control Based on the signals received from the sensors, the ECM controls the exhaust fuel addition injector assembly to purify the Particulate Matter (PM) that is captured in the filter with catalyst. ○ -
Air Fuel Ratio Sensor Heater Control Maintains the temperature of the air fuel ratio sensors at an appropriate level to increase the detection accuracy of the exhaust gas oxygen concentration. ○ -
Engine Immobiliser Prohibits fuel injection if an attempt is made to start the engine with an invalid key. ○ ○
Diagnosis When the ECM detects a malfunction, it records the malfunction and memorizes information related to the fault. ○ ○
Fail-safe When the ECM detects a malfunction, it stops or controls the engine according to the data already stored in the memory. ○ ○
Brake Override System The driving torque is restricted when the brake pedal is depressed while the accelerator pedal is depressed. (For the Activation Conditions and Inspection Method, refer to the Repair Manual.) ○ ○



Construction


a.

The configuration of the engine control system is as shown in the following chart.

W133297E01
0.667,0.094 2.458,0.448 1.792,0.354 10 false Crank Position Sensor 0.635,0.823 2.427,1.177 1.792,0.354 10 false Cam Position Sensor 0.5,1.583 2.26,2.333 1.76,0.75 10 false Intake Mass Air Flow Meter Sub-assembly 0.594,2.521 2.115,3.271 1.521,0.75 10 false Intake Air Temperature Sensor 0.458,3.771 2.313,4.135 1.854,0.365 10 false Fuel Temperature Sensor 0.583,4.51 2.115,4.865 1.531,0.354 10 false Fuel Pressure Sensor 0.385,5.24 2.469,6.021 2.083,0.781 10 false Intake Air Temperature Sensor (Intake Manifold) 0.146,6.385 2.417,6.75 2.271,0.365 10 false Accelerator Pedal Sensor Assembly 0.604,7.125 2.458,7.49 1.854,0.365 10 false Turbo Pressure Sensor 0.167,7.854 2.427,8.208 2.26,0.354 10 false Engine Coolant Temperature Sensor 3.406,3.51 3.875,4 0.469,0.49 10 false ECM 4.698,0.906 5.229,2.021 0.531,1.115 10 false No. 1 Injector Driver 5.521,0.094 7.042,0.458 1.521,0.365 10 false No. 1 Injector Assembly 5.51,0.51 7.031,0.875 1.521,0.365 10 false No. 4 Injector Assembly 5.531,0.927 7.052,1.292 1.521,0.365 10 false No. 6 Injector Assembly 5.51,1.344 7.031,1.708 1.521,0.365 10 false No. 7 Injector Assembly 5.49,1.906 7.01,2.656 1.521,0.75 10 false Fuel Pressure Discharge Valve* 4.063,1.906 4.24,2.083 0.177,0.177 10 false * 4.073,2.594 4.25,2.771 0.177,0.177 10 false * 4.052,6.26 4.229,6.438 0.177,0.177 10 false * 5.281,3.073 6.958,3.448 1.677,0.375 10 false No. 1 EDU Relay 4.677,4.906 5.208,6.021 0.531,1.115 10 false No. 2 Injector Driver 5.51,4.219 7.031,4.583 1.521,0.365 10 false No. 2 Injector Assembly 5.51,4.635 7.031,5 1.521,0.365 10 false No. 3 Injector Assembly 5.51,5.052 7.031,5.417 1.521,0.365 10 false No. 5 Injector Assembly 5.5,5.469 7.021,5.833 1.521,0.365 10 false No. 8 Injector Assembly 5.344,6.729 7.021,7.104 1.677,0.375 10 false No. 2 EDU Relay 5.031,7.865 6.938,8.198 1.906,0.333 10 false Suction Control Valve (SCV) 0.115,8.313 3.969,8.698 3.854,0.385 10 false *: Models compliant with EURO 5 emission regulations

W133298E01
0.292,0.094 2.448,0.448 2.156,0.354 10 false Throttle Position Sensor (Bank 1) 0.302,0.958 2.458,1.313 2.156,0.354 10 false Throttle Position Sensor (Bank 2) 0.104,1.813 2.479,2.188 2.375,0.375 10 false EGR Valve Position Sensor (Bank 1)*1 0.104,2.677 2.479,3.052 2.375,0.375 10 false EGR Valve Position Sensor (Bank 2)*1 5.406,0.073 7.01,0.427 1.604,0.354 10 false EGR Control*1 5.01,0.604 6.99,0.958 1.979,0.354 10 false No. 1 EGR Valve Assembly 4.969,1.156 6.948,1.51 1.979,0.354 10 false No. 2 EGR Valve Assembly 5.448,1.927 7.052,2.281 1.604,0.354 10 false Throttle Control 4.99,2.448 6.885,3.167 1.896,0.719 10 false Diesel Throttle Control Motor (Bank 1) 5.021,3.406 6.917,4.125 1.896,0.719 10 false Diesel Throttle Control Motor (Bank 2) 0.281,3.531 2.479,3.906 2.198,0.375 10 false Air Fuel Ratio Sensor (Bank 1)*2 0.26,4.396 2.458,4.771 2.198,0.375 10 false Air Fuel Ratio Sensor (Bank 2)*2 0.125,5.25 2.49,5.615 2.365,0.365 9 false Nozzle Vane Position Sensor (Bank 1)*2 0.115,6.125 2.49,6.479 2.375,0.354 9 false Nozzle Vane Position Sensor (Bank 2)*2 0.104,6.969 2.49,7.417 2.385,0.448 9 false Differential Pressure Sensor (Bank 1)*2 0.104,7.833 2.469,8.26 2.365,0.427 9 false Differential Pressure Sensor (Bank 2)*2 5.292,4.563 7.031,4.938 1.74,0.375 9 false Glow Plug Control 5.156,5.104 6.885,5.792 1.729,0.688 9 false Glow Plug Relay Assembly (Bank 1) 5.146,6.063 6.875,6.75 1.729,0.688 9 false Glow Plug Relay Assembly (Bank 2) 5.135,7.229 6.875,7.604 1.74,0.375 9 false Engine Mounting Control 5.729,7.74 6.885,8.115 1.156,0.375 9 false VSV 3.438,3.646 3.833,4.406 0.396,0.76 10 false ECM 0.073,8.26 4.427,8.563 4.354,0.302 10 false *1: Models compliant with emission regulations 0.052,8.563 5.323,8.865 5.271,0.302 10 false *2: Models compliant with EURO 5 emission regulations

W133299E01
0.26,0.115 2.458,0.854 2.198,0.74 10 false Exhaust Gas Temperature Sensor (Bank 1, Sensor 1)*1 0.26,1.406 2.458,2.146 2.198,0.74 10 false Exhaust Gas Temperature Sensor (Bank 1, Sensor 2)*1 0.25,2.698 2.448,3.438 2.198,0.74 10 false Exhaust Gas Temperature Sensor (Bank 1, Sensor 3)*1 0.24,3.99 2.438,4.729 2.198,0.74 10 false Exhaust Gas Temperature Sensor (Bank 2, Sensor 1)*1 0.24,5.292 2.438,6.031 2.198,0.74 10 false Exhaust Gas Temperature Sensor (Bank 2, Sensor 2)*1 0.177,6.594 2.375,7.333 2.198,0.74 10 false Exhaust Gas Temperature Sensor (Bank 2, Sensor 3)*1 0.875,7.875 2.375,8.229 1.5,0.354 10 false DPF Switch*1 5.188,0.104 7.063,0.469 1.875,0.365 10 false Turbocharger Control*1 5.302,0.625 6.958,1 1.656,0.375 10 false DC Motor (Bank 1) 5.292,1.188 6.948,1.563 1.656,0.375 10 false DC Motor (Bank 2) 5.156,3.646 7.031,4.01 1.875,0.365 10 false Turbocharger Control*2 5.094,4.167 6.969,4.531 1.875,0.365 10 false Turbo Motor Driver (Bank 1) 5.448,4.74 6.948,5.51 1.5,0.771 10 false Nozzle Vane Position Sensor (Bank 1) 5.531,5.688 6.958,6.073 1.427,0.385 10 false DC Motor (Bank 1) 5.083,6.25 6.958,6.615 1.875,0.365 10 false Turbo Motor Driver (Bank 2) 5.448,6.802 6.948,7.573 1.5,0.771 10 false Nozzle Vane Position Sensor (Bank 2) 5.521,7.76 6.948,8.146 1.427,0.385 10 false DC Motor (Bank 2) 0,8.542 3.99,8.865 3.99,0.323 10 false *2: Except models compliant with EURO 5 emission regulations 0,8.271 4.917,8.531 4.917,0.26 10 false *1: Models compliant with EURO 5 emission regulations 3.417,3.552 3.875,4.458 0.458,0.906 10 false ECM

W133300E01
0.177,0.094 2.458,0.458 2.281,0.365 10 false Power Steering Oil Pressure Switch 0.625,0.823 2.479,1.188 1.854,0.365 10 false Generator Assembly 0.469,1.552 2.479,1.948 2.01,0.396 10 false Cruise Control Main Switch*1 0.688,2.292 2.469,2.667 1.781,0.375 10 false Stop Light Switch 0.427,3.01 2.458,3.406 2.031,0.396 10 false First Shift Detection Switch*2 0.76,3.75 2.479,4.146 1.719,0.396 10 false Clutch Switch*2 0.542,4.479 2.479,4.875 1.938,0.396 10 false Pattern Select Switch*3 0.688,5.208 2.49,5.604 1.802,0.396 10 false 4WD Control ECU 0.875,5.938 2.49,6.323 1.615,0.385 10 false EFI Relay 0.177,6.677 2.479,7.083 2.302,0.406 10 false Air Conditioning Amplifier Assembly 0.49,7.406 2.448,7.781 1.958,0.375 10 false Clutch Start Switch*2 3.427,3.875 3.938,4.5 0.51,0.625 10 false ECM 4.938,0.094 6.781,0.875 1.844,0.781 10 false Air Fuel Ratio Sensor Heater Control *4 4.948,1.042 6.917,1.781 1.969,0.74 10 false Air Fuel Ratio Sensor Heater (Bank 1) 4.969,2 6.938,2.74 1.969,0.74 10 false Air Fuel Ratio Sensor Heater (Bank 2) 5.156,6.156 7.031,6.521 1.875,0.365 10 false Fuel Pump Control*5 5.375,6.677 6.969,7.042 1.594,0.365 10 false Fuel Pump Relay 5.521,7.323 6.969,7.677 1.448,0.354 10 false Fuel Pump 0.083,7.833 2.521,8.188 2.438,0.354 10 false *1: Models with cruise control system 0.094,8.167 2.531,8.521 2.438,0.354 10 false *2: Models with manual transmission 0.094,8.51 2.646,8.865 2.552,0.354 10 false *3: Models with automatic transmission 2.865,7.844 7,8.188 4.135,0.344 10 false *4: Models compliant with EURO 5 emission regulations 2.865,8.219 7,8.563 4.135,0.344 10 false *5: Models with dual fuel tank

W133301E01
0.323,0.198 2.292,0.99 1.969,0.792 10 false Park/Neutral Position Switch Assembly*1 0.354,1.021 2.198,1.354 1.844,0.333 10 false - Neutral Start Signal 0.354,1.438 2.292,1.771 1.938,0.333 10 false - Shift Lever Position Signal 0.313,2.208 2.354,2.677 2.042,0.469 10 false Transmission Control Switch*1 0.531,3.167 2.323,3.542 1.792,0.375 10 false Immobiliser Code ECU 0.917,3.906 2.333,4.292 1.417,0.385 10 false IG2 Relay 0.938,4.667 2.354,5.052 1.417,0.385 10 false Battery 1.042,5.427 2.458,5.813 1.417,0.385 10 false DLC3 0.667,6.365 2.396,6.74 1.729,0.375 10 false Combination Meter 1.135,6.875 2.323,7.25 1.188,0.375 10 false MIL 0.615,7.427 2.313,7.813 1.698,0.385 10 false Vehicle Speed Signal 3.375,3.75 3.823,4.219 0.448,0.469 10 false ECM 5.365,0.188 6.906,0.542 1.542,0.354 10 false Starter Control*2 5.385,0.74 6.927,1.094 1.542,0.354 10 false Main Body ECU 5.552,1.333 6.969,1.729 1.417,0.396 10 false ACC Relay 5.438,1.875 6.969,2.281 1.531,0.406 10 false Starter Cut Relay 4.844,2.521 6.979,3.313 2.135,0.792 10 false Clutch Start Switch*3, Park/Neutral Position Switch Assembly*1 5.375,3.573 6.906,3.979 1.531,0.406 10 false Starter Assembly 5.031,5.552 6.885,5.906 1.854,0.354 10 false Catalyst Support Control* 4 4.958,6.063 6.865,6.844 1.906,0.781 10 false Exhaust Fuel Addition Injector Assembly (Bank 1) 4.979,7.031 6.885,7.813 1.906,0.781 10 false Exhaust Fuel Addition Injector Assembly (Bank 2) 0.063,7.979 2.948,8.344 2.885,0.365 10 false *1: Models with automatic transmission 0.083,8.302 2.969,8.667 2.885,0.365 10 false *2: Models with entry and start system 2.719,7.979 5.604,8.344 2.885,0.365 10 false *3: Models with manual transmission 2.729,8.344 6.656,8.75 3.927,0.406 10 false *3: Models compliant with EURO 5 emission regulations



Layout of Main Components


W133144C01
1.865,2.115 1.542,1.177 true 1.271,2.219 0.885,1.5 true 0.26,3.438 0.771,2.667 true 0.875,4.135 1.99,2.271 true 1.208,4.25 2.135,2.323 true 1.865,4.49 2.271,2.885 true 2.917,4.49 2.635,2.844 true 3.49,4.385 2.823,3.021 true 4.042,4.198 3.313,3 true 4.74,4.01 3.5,2.938 true 5.573,3.76 4.021,2.26 true 3.052,2.719 4.5,0.281 true 2.958,2.688 3.948,0.344 true 2.875,2.719 3.5,0.458 true 2.729,2.5 3.083,0.542 true 2.396,4.552 2.469,2.844 true 2.333,2.604 2.458,0.74 true 1.427,1 1.74,1.156 0.313,0.156 10 false *1 0.76,1.344 1.073,1.5 0.313,0.156 10 false *2 0.073,3.438 0.531,3.677 0.458,0.24 10 false *3 (*A) 0.719,4.115 1.031,4.271 0.313,0.156 10 false *4 1.073,4.25 1.385,4.406 0.313,0.156 10 false *5 1.781,4.552 2.094,4.708 0.313,0.156 10 false *6 2.25,4.604 2.719,4.781 0.469,0.177 10 false *7 (*B) 2.781,4.521 3.24,4.708 0.458,0.188 10 false *8 (*B) 3.396,4.406 3.865,4.604 0.469,0.198 10 false *9 (*B) 3.948,4.24 4.49,4.448 0.542,0.208 10 false *10 (*B) 4.708,4.031 5.271,4.24 0.563,0.208 10 false *11 (*B) 5.594,3.823 6.188,4.031 0.594,0.208 10 false *12 4.479,0.083 5.031,0.292 0.552,0.208 10 false *13 (*B) 3.865,0.167 4.417,0.385 0.552,0.219 10 false *14 (*B) 3.323,0.24 3.844,0.448 0.521,0.208 10 false *15 (*B) 2.802,0.344 3.292,0.521 0.49,0.177 10 false *16 (*B) 2.25,0.531 2.781,0.708 0.531,0.177 10 false *17 (*B)
*A Except Models Compliant with EURO 5 Emission Regulations *B Models Compliant with EURO 5 Emission Regulations
*1 ECM *2 Intake Mass Air Flow Meter Sub-assembly
·

Intake Air Temperature Sensor


*3 Turbo Motor Driver *4 Manifold Absolute Pressure Sensor
*5 Intake Air Temperature Sensor (Intake Manifold) *6 Injector Driver
*7 Exhaust Gas Temperature Sensor (Bank 1, Sensor 2) *8 Exhaust Gas Temperature Sensor (Bank 2, Sensor 1)
*9 Exhaust Gas Temperature Sensor (Bank 2, Sensor 2) *10 Exhaust Gas Temperature Sensor (Bank 2, Sensor 3)
*11 Air Fuel Ratio Sensor (Bank 2) *12 Fuel Suction with Pump and Gauge Tube Assembly
·

Fuel Pump (Models with Dual Fuel Tank)


*13 Differential Pressure Sensor (Bank 2) *14 Air Fuel Ratio Sensor (Bank 1)
*15 Exhaust Gas Temperature Sensor (Bank 1, Sensor 3) *16 Differential Pressure Sensor (Bank 1)
*17 Exhaust Gas Temperature Sensor (Bank 1, Sensor 1) - -


W133145C01
2.365,1.344 2.156,0.74 true 1.76,2.865 2.469,2.094 true 3.156,3.375 2.698,2.271 true 3.938,0.479 3.125,1.865 true 2.042,0.531 2.354,0.688 0.313,0.156 10 false *1 1.635,2.875 1.948,3.031 0.313,0.156 10 false *2 3.156,3.427 3.469,3.583 0.313,0.156 10 false *3 3.844,0.292 4.302,0.479 0.458,0.188 10 false *4 (*A)
*A Models Compliant with EURO 5 Emission Regulations - -
*1 Combination Meter
·

MIL

·

Multi-information Display (Models with Optitron Type Combination Meter)


*2 Accelerator Pedal Sensor Assembly
*3 DLC3 *4 DPF Switch


W133146C01
3.615,7.115 6.688,9.688 3.073,2.573 0.542,7.115 3.615,9.688 3.073,2.573 1.75,1.552 2.281,1.542 true 2.385,0.521 2.729,0.802 true 2.094,0.948 2.688,1.146 true 1.938,3.01 2.552,2.75 true 3.469,1.802 5.5,1.521 true 4.656,0.823 5.156,0.417 true 4.104,3.719 3.875,4.365 true 3.688,3.75 3.635,4.333 true 2.208,4.302 3.156,4.885 true 2,4.833 3.333,5.125 true 2.188,6.729 3.24,6.052 true 5.281,6.458 4.792,5.938 true 5.583,5.677 4.354,5.073 true 5.729,4.885 4.927,4.906 true 5.073,3.938 4.583,4.302 true 5.583,4.438 4.656,4.76 true 1.646,7.333 1.927,7.49 true 2.938,7.667 3.156,7.469 true 4.167,7.313 4.448,7.469 true 5.552,7.688 5.771,7.49 true 3.896,9.24 4.156,8.75 true 1.365,9.229 1.625,8.74 true 2.229,0.365 2.542,0.521 0.313,0.156 10 false *1 1.906,0.854 2.219,1.01 0.313,0.156 10 false *2 1.531,1.479 1.844,1.635 0.313,0.156 10 false *3 1.792,3.01 2.104,3.167 0.313,0.156 10 false *4 5.573,1.438 5.885,1.594 0.313,0.156 10 false *5 5.156,0.281 5.469,0.438 0.313,0.156 10 false *6 1.99,4.167 2.302,4.323 0.313,0.156 10 false *7 1.813,4.719 2.125,4.875 0.313,0.156 10 false *8 2.063,6.719 2.375,6.875 0.313,0.156 10 false *9 5.323,6.469 5.792,6.625 0.469,0.156 10 false *10 5.677,5.667 6.146,5.823 0.469,0.156 10 false *11 5.635,4.354 6.25,4.531 0.615,0.177 10 false *12 (*A) 5.146,3.792 5.615,3.948 0.469,0.156 10 false *13 4.031,3.542 4.5,3.698 0.469,0.156 10 false *14 3.531,3.563 4,3.719 0.469,0.156 10 false *15 1.396,7.188 1.865,7.344 0.469,0.156 10 false *16 3.188,7.333 3.656,7.49 0.469,0.156 10 false *17 5.802,4.813 6.115,4.969 0.313,0.156 10 false *3 0.604,7.146 0.917,7.354 0.313,0.208 12 false *A: 3.656,7.135 3.969,7.344 0.313,0.208 12 false *B: 1.292,9.26 1.604,9.417 0.313,0.156 10 false *7 0.99,7.521 1.302,7.677 0.313,0.156 10 false *a 3.948,7.188 4.417,7.344 0.469,0.156 10 false *16 5.781,7.344 6.25,7.5 0.469,0.156 10 false *17 3.792,9.271 4.104,9.427 0.313,0.156 10 false *7 5.688,3.24 6,3.396 0.313,0.156 10 false *a 1.396,6.406 1.708,6.563 0.313,0.156 10 false *a
*A Models Compliant with EURO 5 Emission Regulations *B Except Models Compliant with EURO 5 Emission Regulations
*1 Diesel Throttle Body Assembly (Bank 1)
·

Throttle Position Sensor

·

Diesel Throttle Control Motor


*2 Fuel Pressure Sensor
*3 Injector Assembly *4 Turbocharger Sub-assembly (Bank 1)
·

DC Motor

·

Nozzle Vane Position Sensor


*5 Glow Plug Assembly *6 Engine Coolant Temperature Sensor
*7 Supply Pump Assembly *8 Cam Position Sensor
*9 Crank Position Sensor *10 Turbocharger Sub-assembly (Bank 2)
·

DC Motor

·

Nozzle Vane Position Sensor


*11 VSV (for Engine Mount Control) *12 Fuel Pressure Discharge Valve
*13 Diesel Throttle Body Assembly (Bank 2)
·

Throttle Position Sensor

·

Diesel Throttle Control Motor


*14 No. 2 EGR Valve Assembly
·

EGR Valve Position Sensor (Bank 2)


*15 No. 1 EGR Valve Assembly
·

EGR Valve Position Sensor (Bank 1)


*16 Fuel Temperature Sensor
*17 SCV - -
*a Front - -


Models Compliant with EURO 5 Emission Regulations
W133147C01
2.396,2.646 3.396,1.833 true 4.583,1.583 5.813,1.708 true 2.188,2.646 2.5,2.802 0.313,0.156 10 false *1 5.844,1.646 6.156,1.802 0.313,0.156 10 false *2 1.823,0.281 2.135,0.438 0.313,0.156 10 false *a
*1 Exhaust Fuel Addition Injector Assembly (Bank 2) *2 Exhaust Fuel Addition Injector Assembly (Bank 1)
*a Front - -



Main Components of Engine Control System


a.

General

i.

The engine control system of the 1VD-FTV engine has the following system.

Component Outline Quantity Function

*1: Except models compliant with EURO 5 emission regulations

*2: Models compliant with EURO 5 emission regulations

ECM 32-bit CPU (DENSO) 1 The ECM effects overall control of the engine control system to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
Injector Driver DC/DC Converter 2 The injector driver is used to drive the injector assembly at high speeds. The injector driver has realized high-speed driving under high fuel pressure conditions through the use of a DC/DC converter that provides a high voltage, quick-charging system.
Intake Mass Air Flow Meter Sub-assembly Hot-wire Type 1 This sensor uses a built-in hot-wire to directly detect the intake air mass and flow rate.
Atmospheric Temperature Sensor Thermistor Type 1 This sensor detects the atmospheric temperature by means of an internal thermistor.
Fuel Pressure Sensor Semiconductor Strain Gauge Type 1 This sensor uses built-in semiconductors to detect the internal pressure of the common-rail assembly.
Manifold Absolute Pressure Sensor Semiconductor Silicon Chip Type 1 This sensor uses built-in semiconductors to detect the intake manifold pressure.
Atmospheric Pressure Sensor Semiconductor Silicon Chip Type 1 This sensor, which is built into the ECM, uses semiconductors to detect the atmospheric pressure.
Crank Position Sensor Pick-up Coil Type (Rotor Teeth /36-2) 1 This sensor detects the engine speed and performs the cylinder identification.
Cam Position Sensor Pick-up Coil Type (Rotor Teeth /1) 1 This sensor performs the cylinder identification.
Throttle Position Sensor Non-contact Type 2 This sensor detects the throttle valve opening angle.
Accelerator Pedal Sensor Assembly No-contact Type 1 This sensor detects the amount of pedal effort applied to the accelerator pedal.
Engine Coolant Temperature Sensor Thermistor Type 1 This sensor detects the engine coolant temperature by means of an internal thermistor.
Intake Air Temperature Sensor Thermistor Type 1 This sensor detects the intake air temperature after the intercooler.
Fuel Temperature Sensor Thermistor Type 1 This sensor detects the fuel temperature in the supply pump assembly by means of an internal thermistor.
Suction Control Valve (SCV) Linear Solenoid Valve 1 The SCV position is controlled by the signals from the ECM, and a fuel volume that suits the SCV position is drawn into the pumping portion (plunger portion).
Injector Assembly 9-hole, Solenoid Type*1 8 The injector assembly injects the fuel to the combustion chamber in accordance with the ECM signals via the injector driver.
9-hole, Piezo Type*2
Exhaust Fuel Addition Injector Assembly*2 Solenoid Type 2 (1 each bank) Injects fuel into the fuel injection passage of the cylinder head sub-assembly.
Differential Pressure Sensor*2 - 2 (1 each bank)
·

Monitors the differential pressure before and after the DPF.

·

Compares this data with the PM accumulation amount calculated by the ECM. If there is a large deviation in the comparison result, the ECM corrects the PM accumulation amount.


Exhaust Gas Temperature Sensor*2 Thermistor Type 6 (3 each bank) Detects the exhaust gas temperature.
Air Fuel Ratio Sensor (Bank 1, Sensor 1)*2 - 1 Detects the oxygen concentration in exhaust gas.
Air Fuel Ratio Sensor (Bank 2, Sensor 1)*2 1



b.

Intake Mass Air Flow Meter Sub-assembly

i.

The intake mass air flow meter sub-assembly of diesel engine uses precise fuel injection volume control and EGR control to realize clean emission.


ii.

This intake mass air flow meter sub-assembly, which is a slot-in type, allows a portion of the intake air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air, the detection precision is improved and the intake air resistance is reduced.


iii.

The intake mass air flow meter sub-assembly has a built-in atmospheric temperature sensor.

W128425C03
5.115,1.906 5.594,1.604 true 5.615,1.469 5.854,1.698 0.24,0.229 10 false *1
*1 Atmospheric Temperature Sensor - -
V100135

Air Flow - -




c.

Fuel Pressure Sensor

i.

The fuel pressure sensor consists of a semiconductor which utilizes the characteristic of a silicon chip that changes its electrical resistance when pressure is applied to it. This sensor is mounted on the common-rail assembly, outputs a signal that represents the fuel pressure in the common-rail assembly to the ECM, in order to constantly regulate the fuel at an optimal pressure.

W133148E01
2.281,1.323 1.833,0.427 1.833,0.427 1.583,0.427 true 0.438,0.354 1.573,0.781 1.135,0.427 10 false Detection Portion 3.708,0.063 5.177,0.427 1.469,0.365 10 false Output Characteristic 4.354,0.635 4.813,0.833 0.458,0.198 10 false (V) 3.938,1.083 4.479,1.74 0.542,0.656 10 false Output Voltage 4.74,2.01 5.771,2.375 1.031,0.365 10 false Fuel Pressure 6.042,1.99 6.813,2.188 0.771,0.198 10 false (MPa)



d.

Manifold Absolute Pressure Sensor

i.

The manifold absolute pressure sensor consists of a semiconductor which utilizes the characteristic of a silicon chip that changes its electrical resistance when pressure is applied to it. The sensor converts the intake air pressure into an electrical signal, and sends it to the ECM in an amplified form.

W133149E01
1.448,1.156 1.208,0.333 1.208,0.333 0.927,0.333 true 0.083,0.271 0.979,0.708 0.896,0.438 10 false Sensor Unit 3.615,0.052 5.365,0.417 1.75,0.365 10 false Output Characteristic 3.385,1.354 4.344,1.771 0.958,0.417 10 false Output Voltage 4.156,0.625 4.615,0.823 0.458,0.198 10 false (V) 4.281,2.094 4.438,2.292 0.156,0.198 10 false 0 4.573,2.156 6.177,2.594 1.604,0.438 10 false Intake Manifold Pressure 6.135,2.01 6.906,2.208 0.771,0.198 10 false (kPa)



e.

Crank Position Sensor

i.

The timing rotor of the crankshaft consists of 34 teeth, with 2 teeth missing. The crank position sensor outputs the crankshaft rotation signals every 10°, and the missing teeth are used to determine the top-dead-center.

W133150E01
1.021,1.438 2.052,0.156 2.052,0.156 2.469,0.156 true 1.479,2.01 2.094,3.26 2.094,3.26 2.354,3.26 true 5.99,3.469 6.271,3.469 6.271,3.469 6.427,2.115 true 2.563,0.073 4.563,0.865 2,0.792 10 false Timing Rotor (No.1 Crankshaft Position Sensor Plate) 2.438,3.177 4.229,3.521 1.792,0.344 10 false Crank Position Sensor 4.458,1.333 6.229,1.625 1.771,0.292 10 false NE Signal Plate (720° CA) 5.094,2.781 5.729,3.042 0.635,0.26 10 false 10° CA 4.979,3.365 5.969,3.677 0.99,0.313 10 false 2 Teeth Missing



f.

Cam Position Sensor

i.

The cam position sensor generates one signal in every two revolutions of the crankshaft by using the timing trigger of the No. 2 camshaft timing sprocket.

W133151E02
1.615,1.063 2.156,0.146 2.156,0.146 2.583,0.146 true 1.427,1.125 1.396,0.198 1.396,0.198 1.125,0.198 true 1.219,1.281 1.354,2.281 1.354,2.281 1.677,2.281 true 2.719,0.073 4.104,0.927 1.385,0.854 10 false No. 2 Camshaft Timing Sprocket 0.094,0.115 1.083,0.479 0.99,0.365 10 false Timing Trigger 1.75,2.208 3.552,2.615 1.802,0.406 10 false Cam Position Sensor 4.646,1.906 6.333,2.458 1.688,0.552 10 false G Signal Plate (720° CA)



g.

Throttle Position Sensor

i.

The throttle position sensor is mounted on the diesel throttle body, to detect the opening angle of the throttle valve. The throttle position sensor converts the magnetic flux density that changes when the magnetic yoke (located on the same axis as that of the throttle valve shaft) rotates around the Hall IC into electric signals to operate the diesel throttle control motor.

W133152E01
0.979,1.365 1.094,0.208 1.094,0.208 1.365,0.208 true 0.938,1.219 0.927,0.167 0.927,0.167 0.677,0.167 true 0.938,1.51 0.948,2.167 0.948,2.167 0.729,2.167 true 1.906,1.76 1.917,2.417 1.917,2.417 1.719,2.417 true 1.417,0.135 2.083,0.417 0.667,0.281 10 false Hall IC 0.052,0.083 0.656,0.74 0.604,0.656 10 false Magnetic Yoke 0.083,2.083 0.688,2.74 0.604,0.656 10 false Magnetic Yoke 0.844,2.354 1.719,2.74 0.875,0.385 10 false Throttle Valve 3.167,0.021 4.99,0.438 1.823,0.417 10 false Output Characteristic 3.24,1.219 4.24,1.646 1,0.427 10 false Output Voltage 4.083,0.354 4.542,0.552 0.458,0.198 10 false (V) 6.865,2.25 7.156,2.479 0.292,0.229 10 false (%) 4.583,2.26 6.458,2.688 1.875,0.427 10 false Throttle Valve Position Ratio 4.156,2.229 4.375,2.625 0.219,0.396 10 false 0 4.135,0.563 4.354,0.958 0.219,0.396 10 false 5 6.521,2.26 6.844,2.656 0.323,0.396 10 false 100



h.

Accelerator Pedal Sensor Assembly

i.

The no-contact type accelerator pedal sensor assembly uses a Hall IC, which is mounted on the accelerator pedal arm.


ii.

A magnetic yoke is mounted at the base of the accelerator pedal arm. This yoke rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes that occur in the magnetic flux into electrical signals, and outputs them in the form of accelerator pedal position signals to the ECM.


iii.

The Hall IC contains two circuits, one for the main signal, and the other for the sub signal. It converts the accelerator pedal position (angle) into electric signals that have differing characteristics and outputs them to the ECM.

W132291C01
2.229,1.927 3.073,1.625 true 3.844,1.583 4.854,1.021 true 4.375,2.26 5.198,1.969 true 2.031,1.896 2.344,2.052 0.313,0.156 10 false *1 4.906,0.906 5.219,1.063 0.313,0.156 10 false *2 5.229,1.875 5.542,2.031 0.313,0.156 10 false *3
*1 Hall IC *2 Magnetic Yoke
*3 Accelerator Pedal Arm - -


W132962E02
1.188,1.323 1.188,0.823 1.188,0.823 0.917,0.823 true 1.271,1.563 1.521,0.302 1.521,0.302 1.844,0.302 true 1.188,2.375 1.188,2.771 1.188,2.771 0.917,2.771 true 1.271,2.406 2.104,3.208 2.104,3.208 2.604,3.208 true 0.74,1.625 0.073,0.26 0.073,0.26 0.396,0.26 true 0.26,3.083 1.958,3.76 1.698,0.677 10 false Accelerator Pedal Sensor Assembly 0.406,0.729 0.938,1.073 0.531,0.344 10 false Magnet 1.885,0.229 2.521,0.531 0.635,0.302 10 false Hall IC 2.073,0.938 2.438,1.135 0.365,0.198 10 false VPA 2.073,1.25 2.406,1.458 0.333,0.208 10 false EPA 1.979,1.552 2.417,1.75 0.438,0.198 10 false VCPA 2,1.792 2.438,1.99 0.438,0.198 10 false VPA2 2,2.063 2.438,2.26 0.438,0.198 10 false EPA2 1.99,2.365 2.427,2.563 0.438,0.198 10 false VCP2 0.396,2.677 0.927,3.021 0.531,0.344 10 false Magnet 2.646,3.167 3.281,3.469 0.635,0.302 10 false Hall IC 2.625,1.719 3.01,2.115 0.385,0.396 10 false ECM 3.948,0.938 4.156,1.167 0.208,0.229 10 false V 4.021,1.156 4.229,1.385 0.208,0.229 10 false 5 4.031,2.302 4.24,2.531 0.208,0.229 10 false 0 3.427,1.552 3.948,2.323 0.521,0.771 10 false Output Voltage 4.031,2.667 4.521,3.417 0.49,0.75 10 false Fully Closed 4.802,2.542 6,3.365 1.198,0.823 10 false Accelerator Pedal Position (Angle) 6.313,2.667 6.802,3.417 0.49,0.75 10 false Fully Open 4.76,1.604 5.177,1.802 0.417,0.198 10 false VPA2 5.479,1.969 5.896,2.167 0.417,0.198 10 false VPA 0.417,0.188 1.438,0.521 1.021,0.333 10 false Magnetic Yoke



i.

Differential Pressure Sensor

i.

The differential pressure sensor measures the pressure differences between before and after the DPF with PM in order to detect clogging.


ii.

The sensor is mounted on the transmission. The DPF and the sensor are connected with pipes and hoses.

W133183E01
1.802,2.5 1.573,2.5 1.573,2.5 1.26,1.583 true 1.865,2.417 3.74,2.74 1.875,0.323 10 false Differential Pressure Sensor 3.552,1.219 4.604,1.625 1.052,0.406 10 false Output Voltage 4.438,0.49 4.688,0.896 0.25,0.406 10 false (V) 4.844,2.208 6.292,2.417 1.448,0.208 10 false Differential Pressure 6.458,2.156 6.906,2.458 0.448,0.302 10 false (kPa)



j.

Exhaust Gas Temperature Sensor

i.

An exhaust gas temperature sensor, which is a thermistor type, is installed before the oxidation catalyst, before the DPF and after the DPF, in order to detect the temperature of the exhaust gas.

W133184E01
2.302,0.802 3.042,1.948 0.74,1.146 10 false Electric Resistance Value 3.781,2.271 5.594,2.646 1.813,0.375 10 false Exhaust Gas Temperature 2.813,0.24 3.115,0.458 0.302,0.219 10 false (Ω) 6.448,2.26 6.802,2.5 0.354,0.24 10 false (°C)



k.

Air Fuel Ratio Sensor

i.

A planar type air fuel ratio sensor is used.


ii.

The planar type air fuel ratio sensor uses alumina, which excels in heat conductivity and insulation, to integrate the sensor element with the heater, thus improving the warm-up performance of the sensor.


iii.

This sensor is based on a sensor developed for gasoline engines. The cover has been changed for diesel engine application in order to eliminate the influences of the sensor temperature and the PM. This sensor, which is mounted after the DPF, detects the air fuel ratio after the gas has been reduced.

W133185C01
4.281,1.698 4.115,1.25 true 4.219,1.854 3.906,1.49 true 4.271,2.135 3.958,2.521 true 4.542,1.188 4.354,1.646 true 4.385,2.26 4.844,2.563 true 4.563,2.26 4.938,2.313 true 4.448,2.083 5.031,2.042 true 4.479,1.813 5.063,1.771 true 3.969,1.052 4.281,1.208 0.313,0.156 10 false *1 3.74,1.313 4.052,1.469 0.313,0.156 10 false *2 3.813,2.51 4.125,2.667 0.313,0.156 10 false *3 4.958,2.229 5.271,2.385 0.313,0.156 10 false *4 5.073,1.938 5.385,2.094 0.313,0.156 10 false *5 4.552,1.021 4.865,1.177 0.313,0.156 10 false *6 4.875,2.51 5.188,2.667 0.313,0.156 10 false *3 5.083,1.698 5.396,1.854 0.313,0.156 10 false *2
*1 Diffusion Resistance Layer *2 Alumina
*3 Platinum Electrode *4 Heater
*5 Atmosphere *6 Sensor Element (Zirconia)



iv.

The air fuel ratio sensor data is approximately proportional to the existing air fuel ratio. The air fuel ratio sensor converts the oxygen density to a current and sends it to the ECM.


v.

As a result, the detection precision of the air fuel ratio has been improved. The air fuel ratio sensor data can be read using an Global TechStream (GTS).

W133186E01
0.052,0.802 1.354,2.354 1.302,1.552 10 false Air Fuel Ratio Sensor Data Displayed on Global TechStream (GTS) 1.583,0.771 1.823,1.021 0.24,0.25 10 false 2 1.635,2.021 2,2.302 0.365,0.281 10 false Rich 5.094,2.021 5.458,2.302 0.365,0.281 10 false Lean 2.729,1.979 3.094,2.26 0.365,0.281 10 false 14.5 3.094,2.229 4.094,2.615 1,0.385 10 false Air Fuel Ratio




Fuel Injection Volume Control


a.

The ECM calculates two types of values: the basic injection volume and the maximum injection volume. Then, the ECM compares the basic and maximum injection volumes, and determines a smaller calculated value to be the final injection volume.

Basic Injection Volume
W133153E01
0.25,0.25 2.531,0.573 2.281,0.323 10 false Accelerator Pedal Sensor Assembly 3.052,0.24 4.625,0.552 1.573,0.313 10 false Crank Position Sensor 3.333,0.594 4.49,0.948 1.156,0.354 10 false Engine Speed 0.177,1.156 0.594,1.5 0.417,0.344 10 false ECM 1.167,1.646 3.552,2.042 2.385,0.396 10 false Calculation of Basic Injection Volume 5.302,1.354 6.74,1.656 1.438,0.302 10 false Idle Speed Control 4.771,1.917 7.073,2.281 2.302,0.365 10 false Engine Coolant Temperature Sensor

Maximum Injection Volume
W133154E01
0.333,0.75 2.063,1.76 1.729,1.01 10 false Basic/Maximum Injection Volume (Map data inside of ECM) 0.25,0.302 0.854,0.646 0.604,0.344 10 false ECM 0.604,2.427 1.99,3.5 1.385,1.073 10 false Maximum Injection Volume Correction 2.49,3.604 3.594,4.271 1.104,0.667 10 false Atmospheric Pressure Sensor 5.021,0.292 6.823,0.635 1.802,0.344 10 false Crank Position Sensor 5.302,0.667 6.25,1.01 0.948,0.344 10 false Engine Speed 4.99,1.344 6.656,1.677 1.667,0.333 10 false Fuel Temperature Sensor 4.604,2.042 6.896,2.406 2.292,0.365 10 false Engine Coolant Temperature Sensor 4.792,2.729 6.896,3.073 2.104,0.344 10 false Intake Air Temperature Sensor 4.656,3.417 6.885,3.771 2.229,0.354 10 false Manifold Absolute Pressure Sensor 4.49,4.125 7.063,4.427 2.573,0.302 10 false Intake Mass Air Flow Meter sub-assembly

Final Injection Volume Decision
W133155E01
0.083,0.521 0.531,0.875 0.448,0.354 10 false ECM 0.375,1.073 2,1.448 1.625,0.375 10 false Basic Injection Volume 0.302,2.406 2.021,2.76 1.719,0.354 10 false Maximum Injection Volume 2.615,1.708 3.438,2.104 0.823,0.396 10 false Comparison 3.583,1.083 4.688,1.406 1.104,0.323 10 false Fuel Pressure 4.677,1.688 5.125,2.104 0.448,0.417 10 false Final 6.021,1.083 6.979,1.823 0.958,0.74 10 false No. 1 Injector Driver 6.021,2 6.979,2.74 0.958,0.74 10 false No. 2 Injector Driver 5.906,0.458 7.063,0.813 1.156,0.354 10 false Injector Assembly 5.885,3.031 7.042,3.385 1.156,0.354 10 false Injector Assembly



Fuel Injection Timing Control


a.

Fuel injection timing is controlled as shown below.

W133156E01
0.188,0.208 2.448,0.552 2.26,0.344 10 false Accelerator Pedal Sensor Assembly 3.271,0.563 4.354,0.927 1.083,0.365 10 false Engine Speed 2.99,0.198 4.615,0.542 1.625,0.344 10 false Crank Position Sensor 0.135,1.177 0.594,1.458 0.458,0.281 10 false ECM 0.396,1.469 1.885,1.844 1.49,0.375 10 false Basic Injection Timing 0.563,4.625 1.896,4.99 1.333,0.365 10 false Injection Timing 2.688,1.479 3.802,2.167 1.115,0.688 10 false Atmospheric Pressure Sensor 2.865,2.573 3.615,3.25 0.75,0.677 10 false Correction 4.792,2.396 7.073,2.76 2.281,0.365 10 false Engine Coolant Temperature Sensor 4.917,2.917 7.031,3.26 2.115,0.344 10 false Intake Air Temperature Sensor 4.813,3.448 7.073,3.802 2.26,0.354 10 false Manifold Absolute Pressure Sensor 4.656,4 5.625,4.698 0.969,0.698 10 false No. 1 Injector Driver 4.656,4.906 5.625,5.604 0.969,0.698 10 false No. 2 Injector Driver 6.177,3.99 7.052,4.708 0.875,0.719 10 false Injector Assembly 6.156,4.896 7.031,5.615 0.875,0.719 10 false Injector Assembly



During Starting Control


a.

Injection Volume Control

i.

The starting injection volume is determined by adjusting the basic injection volume in accordance with the starter ON signals (ON time), engine coolant temperature sensor signals and engine speed signal. When the engine is cold, the engine coolant temperature will be lower and the injection volume will be greater.

W133157E01
0.094,0.198 0.552,0.51 0.458,0.313 10 false ECM 0.427,0.625 1.927,0.969 1.5,0.344 10 false Basic Injection Volume 0.823,1.688 1.667,2.031 0.844,0.344 10 false Correction 4.75,1.677 7.052,2.031 2.302,0.354 10 false Engine Coolant Temperature Sensor 5.479,1.156 6.646,1.479 1.167,0.323 10 false Starter Signal 5.188,2.219 7.042,2.583 1.854,0.365 10 false Crank Position Sensor



b.

Injection Timing Control

i.

To determine the starting injection timing, the target injection timing is corrected in accordance with the starter signals, engine coolant temperature, and engine speed. When the engine coolant temperature is low, if the engine speed is high, the injection timing is advanced.

W133158E01
0.104,0.135 0.635,0.406 0.531,0.271 10 false ECM 0.333,0.469 1.958,1.292 1.625,0.823 10 false Target Injection Timing Correction 5.417,0.198 6.927,0.552 1.51,0.354 10 false Starter Signal 4.729,0.719 7.063,1.073 2.333,0.354 10 false Engine Coolant Temperature Sensor 5.188,1.25 7.052,1.604 1.865,0.354 10 false Crank Position Sensor




Idle Speed Control


a.

Idle speed is controlled as shown below.

W133159E01
0.125,0.146 0.635,0.438 0.51,0.292 10 false ECM 0.51,1.438 2.115,1.865 1.604,0.427 10 false Target Speed Calculation 4.698,0.323 6.99,0.698 2.292,0.375 10 false Accelerator Pedal Sensor Assembly 4.708,0.875 7,1.25 2.292,0.375 10 false Engine Coolant Temperature Sensor 5.104,1.427 6.99,1.802 1.885,0.375 10 false Vehicle Speed Signal 5.333,1.99 6.979,2.354 1.646,0.365 10 false Starter Signal 4.594,2.552 7.052,2.927 2.458,0.375 10 false Park/Neutral Position Switch Assembly* 4.688,3.104 6.969,3.479 2.281,0.375 10 false Power Steering Oil Pressure Switch 5.198,3.667 7.031,4.021 1.833,0.354 10 false Stop Light Switch* 5.375,4.229 7,4.563 1.625,0.333 10 false Idle-up Signal 5.208,4.802 6.979,5.135 1.771,0.333 10 false Air Conditioning Signal 5.302,5.344 6.927,5.677 1.625,0.333 10 false Generator Signal 5.146,5.906 6.927,6.25 1.781,0.344 10 false Crank Position Sensor 0.563,4.667 1.625,4.99 1.063,0.323 10 false Comparison 1.51,5.302 3.281,5.625 1.771,0.323 10 false Injection Volume Correction 0.281,5.906 1.625,6.229 1.344,0.323 10 false Actual Engine Speed 0.177,6.479 2.875,6.781 2.698,0.302 10 false *: Models with Automatic Transmission



Fuel Pressure Control


a.

General

i.

Except Models Compliant with EURO 5 Emission Regulations

·

The ECM calculates the target injection pressure (25 MPa to 175 MPa*1, 25 MPa to 129 MPa*2) based on the engine conditions, that are the signals from the accelerator pedal sensor assembly and the crank position sensor.

·

To control fuel pressure, signals sent to Suction Control Valve (SCV) of the supply pump assembly regulate the pumping volume, so that the pressure detected by the fuel pressure sensor matches the target injection pressure.

*1: Models compliant with EURO 4 emission regulations

*2: Except models compliant with EURO 4 emission regulations



W133160E01
1.083,5.354 1.146,4.865 1.146,4.865 1.323,4.865 true 0.719,0.146 1.177,0.427 0.458,0.281 10 false ECM 1.198,0.458 3.177,0.833 1.979,0.375 10 false Atmospheric Pressure Sensor 1.198,1.552 3.031,3.323 1.833,1.771 10 false Calculation of Target Injection Pressure 5.146,0.125 6.865,0.479 1.719,0.354 10 false Crank Position Sensor 4.677,0.688 6.979,1.021 2.302,0.333 10 false Accelerator Pedal Sensor Assembly 4.771,1.25 6.99,1.573 2.219,0.323 10 false Atmospheric Temperature Sensor 4.76,1.802 6.979,2.125 2.219,0.323 10 false Engine Coolant Temperature Sensor 5.365,2.365 6.969,2.698 1.604,0.333 10 false Starter Signal 4.417,3.552 5.781,3.875 1.365,0.323 10 false No. 1 Injector Driver 5.615,4.375 6.979,4.698 1.365,0.323 10 false No. 2 Injector Driver 1.438,4.365 2.906,4.688 1.469,0.323 10 false Fuel Pressure Sensor 4.51,5.177 5.823,5.5 1.313,0.323 10 false Injector Assembly 5.729,6.01 7.01,6.333 1.281,0.323 10 false Injector Assembly 1.625,5.177 3.542,5.521 1.917,0.344 10 false Common-rail Assembly (RH) 1.646,6.01 3.563,6.354 1.917,0.344 10 false Common-rail Assembly (LH) 0.26,5.208 0.75,5.552 0.49,0.344 10 false SCV 1.406,4.781 2.365,5.135 0.958,0.354 10 false Fuel Pumping


ii.

Models Compliant with EURO 5 Emission Regulations

·

The ECM calculates the target injection pressure (32 MPa to 200 MPa) based on the signals from the accelerator pedal sensor assembly and the crank position sensor.

·

To control fuel pressure, signals sent to the Suction Control Valve (SCV) of the supply pump assembly regulate the suction volume, and signals sent to the fuel pressure discharge valve of the common-rail assembly via the No. 1 injector driver regulate the discharge volume, so that the pressure detected by the fuel pressure sensor matches the target injection pressure.

·

A pressure limiter mechanically relieves the pressure if the internal pressure of the common-rail assembly rises abnormally.


W133161E01
3.75,5.219 3.385,4.552 3.385,4.552 3.01,4.552 true 0.969,5.344 1.01,4.906 1.01,4.906 1.156,4.906 true 1.198,6.052 1.146,5.75 1.146,5.75 0.948,5.75 true 4.031,6.229 4.198,5.99 4.198,5.99 4.458,5.99 true 0.719,0.135 1.271,0.417 0.552,0.281 10 false ECM 5.135,0.115 7,0.469 1.865,0.354 10 false Crank Position Sensor 1.146,0.479 3.146,0.813 2,0.333 10 false Atmospheric Pressure Sensor 1.125,1.51 3.031,2.469 1.906,0.958 10 false Calculation of Target Injection Pressure 4.698,0.688 7.021,1.042 2.323,0.354 10 false Accelerator Pedal Sensor Assembly 4.74,1.24 7.063,1.583 2.323,0.344 10 false Atmospheric Temperature Sensor 4.688,1.802 7.01,2.146 2.323,0.344 10 false Engine Coolant Temperature Sensor 5.385,2.365 7.01,2.708 1.625,0.344 10 false Starter Signal 4.635,3.542 6.052,3.896 1.417,0.354 10 false No. 1 Injector Driver 5.604,4.354 7.021,4.708 1.417,0.354 10 false No. 2 Injector Driver 4.708,5.188 6.042,5.542 1.333,0.354 10 false Injector Assembly 5.698,6 7.031,6.354 1.333,0.354 10 false Injector Assembly 0.26,5.198 0.719,5.521 0.458,0.323 10 false SCV 1.708,5.188 3.563,5.521 1.854,0.333 10 false Common-rail Assembly (RH) 1.542,4.479 3.01,4.896 1.469,0.417 10 false Fuel Pressure Sensor 1.24,4.823 2.344,5.125 1.104,0.302 10 false Fuel Pumping 0.042,5.656 0.917,6.781 0.875,1.125 10 false Fuel Pressure Discharge Valve 1.656,6.021 3.51,6.354 1.854,0.333 10 false Common-rail Assembly (LH) 4.521,5.927 5.313,6.531 0.792,0.604 10 false Pressure Limiter



b.

System Operation

i.

General

The ECM controls the opening of the Suction Control Valve (SCV) in order to regulate the volume of fuel that is pumped by the supply pump assembly to the common-rail assembly. Consequently, the fuel pressure in the common-rail assembly is controlled to the target injection pressure.



ii.

SCV Opening Small

(a) When the opening of the SCV is small, the fuel suction area is kept small, which decrease the transferable fuel quantity.

(b) The plunger strokes fully, however, the suction volume becomes small due to the small suction area. Therefore, the difference of the volume between the geometry volume and the suction volume is in vacuum condition.

(c) Pumping will start at the time when the fuel pressure has become higher than the common-rail assembly pressure.


W133162E01
2.542,0.875 2.542,0.26 2.542,0.26 2.771,0.26 true 5.427,0.75 5.594,0.104 5.594,0.104 5.771,0.104 true 0.896,2.354 0.688,2.146 0.688,2.146 0.448,2.146 true 0.948,2.531 0.875,2.813 0.875,2.813 0.594,2.813 true 0.031,1.104 0.813,1.448 0.781,0.344 10 false Cam Stroke 1.708,1.688 2.563,2.031 0.854,0.344 10 false Plunger TDC 2.802,0.177 4.177,0.51 1.375,0.333 10 false Fuel Pumping Mass 4.01,1.719 4.865,2.063 0.854,0.344 10 false Plunger BDC 5.854,0.031 7.042,0.646 1.188,0.615 10 false Pumping Starting Point 0.104,2.073 0.51,2.375 0.406,0.302 10 false SCV 0.042,2.781 0.604,3.708 0.563,0.927 10 false Small Suction Area 1.688,3.448 1.958,3.729 0.271,0.281 10 false (a) 3.615,3.5 3.885,3.781 0.271,0.281 10 false (b) 5.375,3.458 5.646,3.74 0.271,0.281 10 false (c)


iii.

SCV Opening Large

(a) When the opening of the SCV is large, the fuel suction area is kept large, which increase the transferable fuel quantity.

(b) If the plunger strokes fully, the suction volume will increase because the suction area is large.

(c) Pumping will start at the time when the fuel pressure has become higher than the common-rail assembly pressure.


W133163E01
2.74,0.875 2.74,0.125 2.74,0.125 3,0.125 true 4.313,0.719 4.594,0.125 4.594,0.125 4.813,0.125 true 0.865,2.333 0.656,2.052 0.656,2.052 0.49,2.052 true 0.906,2.552 0.792,2.844 0.792,2.844 0.573,2.844 true 0.26,1.031 1.031,1.427 0.771,0.396 10 false Cam Stroke 3.021,0.063 4.396,0.542 1.375,0.479 10 false Fuel Pumping Mass 4.896,0.052 6.74,0.438 1.844,0.385 10 false Pumping Starting Point 0.188,1.979 0.615,2.271 0.427,0.292 10 false SCV 0.063,2.781 0.594,3.75 0.531,0.969 10 false Large Suction Area 1.719,3.521 2.177,3.719 0.458,0.198 10 false (a) 3.906,3.563 4.365,3.76 0.458,0.198 10 false (b) 6.01,3.563 6.469,3.76 0.458,0.198 10 false (c)




Pilot Injection Control


a.

Pilot injection is a method that provides auxiliary fuel injection before the main injection takes place. The purpose of pilot injection is to gently start the combustion of the fuel of the main injection in order to reduce combustion noise.

State Pilot Injection Ordinary Injection
Fuel Injection
W112521E01
0.802,0.604 0.865,0.49 false 1.156,0.604 1.094,0.458 false 0.219,0.615 1.094,0.792 0.875,0.177 8 false Pilot Injection 1.146,0.615 2.021,0.792 0.875,0.177 8 false Main Injection

W112522

Combustion Pressure
W112523

W112524



b.

During pilot injection, the pilot injection volume, timing, and interval (between pilot injection and main injection) are controlled as shown below.

W133164E01
0.219,0.094 2.469,0.427 2.25,0.333 10 false Accelerator Pedal Sensor Assembly 3.25,0.083 4.906,0.406 1.656,0.323 10 false Crank Position Sensor 3.458,0.448 4.844,0.781 1.385,0.333 10 false Engine Speed 5.802,0.094 7.063,0.427 1.26,0.333 10 false Starter Signal 0.135,1.188 0.594,1.438 0.458,0.25 10 false ECM 0.24,1.49 2.01,2.24 1.771,0.75 10 false Basic Pilot Injection (Volume, Timing, Interval) 0.229,4.427 2,5.177 1.771,0.75 10 false Pilot Injection (Volume, Timing, Interval) 2.677,1.5 3.781,2.156 1.104,0.656 10 false Atmospheric Pressure Sensor 2.854,2.823 3.646,3.594 0.792,0.771 10 false Correction 4.927,2.417 7.031,2.75 2.104,0.333 10 false Intake Air Temperature Sensor 4.74,2.927 7.031,3.281 2.292,0.354 10 false Engine Coolant Temperature Sensor 4.823,3.458 7.031,3.823 2.208,0.365 10 false Manifold Absolute Pressure Sensor 4.729,3.979 5.563,4.719 0.833,0.74 10 false No. 1 Injector Driver 4.729,4.875 5.563,5.615 0.833,0.74 10 false No. 2 Injector Driver 6.281,3.969 7.052,4.708 0.771,0.74 10 false Injector Assembly 6.281,4.885 7.052,5.625 0.771,0.74 10 false Injector Assembly



Throttle Control


a.

The opening of the throttle valve is controlled by the ECM in accordance with engine conditions. As a result, the noise that is generated during idling and deceleration, as well as the noise and vibration that are generated when the engine is stopped, have been reduced.

W133165C01
1.198,1.719 1.771,1.531 true 1.333,0.813 1.781,1.042 true 2.573,0.802 3.021,1.031 true 3.104,1.531 3.51,1.292 true 1.115,0.677 1.427,0.833 0.313,0.156 10 false *1 3.542,1.198 3.854,1.354 0.313,0.156 10 false *2 4.458,1.688 4.771,1.844 0.313,0.156 10 false *3 4.479,2.771 4.792,2.927 0.313,0.156 10 false *4 5.542,1.594 5.854,1.75 0.313,0.156 10 false *5 5.552,1.823 5.865,1.979 0.313,0.156 10 false *6 5.542,2.073 5.854,2.229 0.313,0.156 10 false *7 5.552,2.292 5.865,2.448 0.313,0.156 10 false *8 5.573,2.531 5.885,2.688 0.313,0.156 10 false *9 5.563,2.76 6.031,2.917 0.469,0.156 10 false *10 5.583,3 6.052,3.156 0.469,0.156 10 false *11 2.365,0.698 2.677,0.854 0.313,0.156 10 false *1 0.99,1.729 1.302,1.885 0.313,0.156 10 false *2
*1 Diesel Throttle Control Motor *2 Throttle Position Sensor
*3 ECM *4 Atmospheric Pressure Sensor
*5 Engine Speed *6 Vehicle Speed
*7 Engine Coolant Temperature *8 Intake Air Temperature
*9 Accelerator Pedal Position *10 Intake Air Pressure
*11 Starter Signal - -




Turbo Charger Control


a.

General

i.

Except Models Compliant with EURO 5 Emission Regulations

·

The ECM controls nozzle vane positions in the turbocharger sub-assemblies on each bank via the turbo motor drivers in order to obtain the calculated target turbo pressure appropriate to the engine operation conditions.

·

The ECM calculates the optimal nozzle vane position in accordance with the driving conditions (such as engine speed, injection volume, atmospheric pressure and engine coolant temperature), and sends a target nozzle vane position signal to each turbo motor driver. The turbo motor driver controls the nozzle vane position in accordance with this signal and the actual nozzle vane position signal provided by the nozzle vane position sensor.


System Diagram
W133166C01
1.198,3.469 1,3.104 true 1.104,3.573 0.813,3.24 true 4.479,3.135 4.646,2.771 true 5.938,3.49 6.104,3.125 true 6,3.583 6.229,3.323 true 0.865,2.927 1.177,3.083 0.313,0.156 10 false *1 0.615,3.125 0.927,3.281 0.313,0.156 10 false *2 4.625,2.594 4.938,2.75 0.313,0.156 10 false *3 0.938,5.292 1.25,5.448 0.313,0.156 10 false *4 0.948,5.969 1.26,6.125 0.313,0.156 10 false *5 0.958,6.76 1.271,6.917 0.313,0.156 10 false *6 3.458,5.479 3.771,5.635 0.313,0.156 10 false *7 3.438,6.573 3.75,6.729 0.313,0.156 10 false *8 5.948,5.292 6.26,5.448 0.313,0.156 10 false *9 5.938,5.969 6.406,6.125 0.469,0.156 10 false *10 5.938,6.708 6.406,6.865 0.469,0.156 10 false *11 0.875,4.292 1.042,4.563 0.167,0.271 10 false *a 6.083,2.948 6.396,3.104 0.313,0.156 10 false *1 6.271,3.198 6.583,3.354 0.313,0.156 10 false *2 1.25,4.292 1.417,4.563 0.167,0.271 10 false *b 6.104,4.323 6.271,4.594 0.167,0.271 10 false *a 5.708,4.302 5.875,4.573 0.167,0.271 10 false *b 2.469,5.031 2.635,5.302 0.167,0.271 10 false *c 2.469,5.448 2.635,5.719 0.167,0.271 10 false *d 4.51,5.479 4.677,5.75 0.167,0.271 10 false *d 4.552,5.042 4.719,5.313 0.167,0.271 10 false *c
*1 DC Motor *2 Nozzle Vane Position Sensor
*3 Manifold Absolute Pressure Sensor *4 No. 1 Turbo Motor Driver
*5 Crank Position Sensor *6 Accelerator Pedal Sensor Assembly
*7 Atmospheric Pressure Sensor *8 ECM
*9 No. 2 Turbo Motor Driver *10 Engine Coolant Temp. Sensor
*11 Intake Air Temp. Sensor - -
*a Actual Nozzle Vane Position *b Nozzle Vane Position Control
*c Turbocharger Control Status *d Target Nozzle Vane Position



ii.

Models Compliant with EURO 5 Emission Regulations

·

The ECM controls the actuator directly.

·

The ECM controls nozzle vane positions in the turbocharger sub-assemblies on each bank in order to obtain the calculated target turbo pressure appropriate to the engine operation conditions.

·

The ECM calculates the optimal nozzle vane position in accordance with the driving conditions (engine speed, injection volume, atmospheric pressure, and engine coolant temperature etc.), and controls the nozzle vane position in accordance with the optimal nozzle vane position and the actual nozzle vane position signal provided by the nozzle vane position sensor.


System Diagram
W133167C01
1.198,3.49 1.042,3.104 true 1.094,3.583 0.833,3.26 true 5.938,3.49 6.156,3.125 true 6.01,3.583 6.313,3.302 true 4.427,3.146 4.646,2.781 true 6.156,2.958 6.469,3.115 0.313,0.156 10 false *1 0.667,3.104 0.979,3.26 0.313,0.156 10 false *2 4.635,2.604 4.948,2.76 0.313,0.156 10 false *3 0.979,5.979 1.292,6.135 0.313,0.156 10 false *4 0.99,6.729 1.302,6.885 0.313,0.156 10 false *5 3.479,5.646 3.792,5.802 0.313,0.156 10 false *6 3.469,6.573 3.781,6.729 0.313,0.156 10 false *7 5.906,5.99 6.219,6.146 0.313,0.156 10 false *8 5.938,6.719 6.25,6.875 0.313,0.156 10 false *9 2.031,5.073 2.344,5.229 0.313,0.156 10 false *a 2.031,5.458 2.344,5.615 0.313,0.156 10 false *b 6.365,3.229 6.677,3.385 0.313,0.156 10 false *2 0.917,2.938 1.229,3.094 0.313,0.156 10 false *1 4.771,5.083 5.083,5.24 0.313,0.156 10 false *a 4.802,5.469 5.115,5.625 0.313,0.156 10 false *b
*1 DC Motor *2 Nozzle Vane Position Sensor
*3 Manifold Absolute Pressure Sensor *4 Crank Position Sensor
*5 Accelerator Pedal Sensor Assembly *6 Atmospheric Pressure Sensor
*7 ECM *8 Engine Coolant Temp. Sensor
*9 Intake Air Temp. Sensor - -
*a Actual Nozzle Vane Position *b Nozzle Vane Position Control




b.

Construction

i.

General

Variable nozzle vane device is established on the turbine wheel (exhaust) side, and consisted of a DC motor, nozzle vane position sensor, linkage, drive arm, unison ring, driven arms and nozzle vanes.


W133168C01
2.323,1.406 1.552,0.615 true 2.615,1.354 2.969,0.365 true 2.646,2.594 1.656,2.927 true 3.219,3.333 2.958,3.594 true 3.698,3.104 3.844,3.417 true 5.438,1.865 5.354,1.385 true 4.823,3.323 4.99,2.865 true 5.833,2.417 6.156,2.021 true 1.313,0.458 1.625,0.615 0.313,0.156 10 false *1 1.469,2.865 1.781,3.021 0.313,0.156 10 false *2 2.792,3.604 3.104,3.76 0.313,0.156 10 false *3 3.802,3.427 4.115,3.583 0.313,0.156 10 false *4 2.896,0.198 3.208,0.354 0.313,0.156 10 false *5 5.24,1.198 5.552,1.354 0.313,0.156 10 false *6 4.729,3.365 5.042,3.521 0.313,0.156 10 false *7 6.208,1.906 6.521,2.063 0.313,0.156 10 false *8
*1 Turbine Wheel *2 Linkage
*3 Nozzle Vane Position Sensor *4 DC Motor
*5 Nozzle Vane *6 Driven Arm
*7 Unison Ring *8 Drive Arm



ii.

Nozzle Vane Position Sensor

The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the turbo motor driver*1 or ECM*2. The turbo motor driver determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.*1

*1: Except models compliant with EURO 5 emission regulations

*2: Models compliant with EURO 5 emission regulations



W133169E01
1.354,0.656 1.229,0.125 1.229,0.125 0.698,0.125 true 1.51,0.656 1.656,0.125 1.656,0.125 2.823,0.125 true 1.167,0.688 1.167,1.49 1.167,1.49 0.99,1.49 true 1.677,0.698 1.677,1.5 1.677,1.5 2,1.5 true 1.833,1.01 2.583,1.01 true 1.833,3.063 2.24,3.271 2.24,3.271 2.5,3.271 true 0.219,0.052 0.708,0.479 0.49,0.427 10 false Hall IC 2.896,0.052 3.385,0.479 0.49,0.427 10 false Hall IC 0.042,1.375 1.031,1.635 0.99,0.26 10 false Magnetic Yoke 2.031,1.417 3.021,1.677 0.99,0.26 10 false Magnetic Yoke 2.667,0.948 3.51,1.323 0.844,0.375 10 false Sensor Vane 0.188,2.188 0.885,2.469 0.698,0.281 10 false Full Close 2.406,2.177 3.396,2.438 0.99,0.26 10 false Full Open 2.552,3.177 3.542,3.438 0.99,0.26 10 false Sensor Vane 3.896,1.458 4.438,2.156 0.542,0.698 10 false Output Voltage 4.292,0.823 4.75,1.021 0.458,0.198 10 false (V) 4.167,1.073 4.479,1.271 0.313,0.198 10 false 4.5 4.229,2.115 4.542,2.313 0.313,0.198 10 false 0.5 5.146,2.448 6.521,2.74 1.375,0.292 10 false Nozzle Vane Position 4.26,2.854 5.01,3.135 0.75,0.281 10 false Full Close 6.479,2.844 7.094,3.115 0.615,0.271 10 false Full Open 4.135,0.385 5.646,0.823 1.51,0.438 10 false Output Characteristic

System Diagram
W133170E01
0.552,2.292 0.698,2.292 0.698,2.292 0.792,1.948 true 1.656,0.74 1.313,0.417 1.313,0.417 0.771,0.417 true 2.125,0.875 2.125,0.396 2.125,0.396 2.26,0.396 true 2.083,2.406 2.083,2.75 2.083,2.75 2.219,2.75 true 2.25,2.115 2.875,2.677 2.875,2.677 3.063,2.677 true 2.281,1.135 3.156,0.094 3.156,0.094 3.729,0.094 true 1.052,3.01 2.875,3.438 1.823,0.427 10 false Nozzle Vane Position Sensor 0.021,2.229 0.521,2.896 0.5,0.667 10 false Sensor Vane 0.115,0.313 0.76,0.969 0.646,0.656 10 false Magnetic Yoke 2.302,0.344 2.823,0.646 0.521,0.302 10 false Magnet 2.271,2.677 2.792,2.979 0.521,0.302 10 false Magnet 3.104,2.573 3.583,2.969 0.479,0.396 10 false Hall IC 3.792,0.01 4.531,0.281 0.74,0.271 10 false Hall IC 3.802,1.063 4.656,2.354 0.854,1.292 10 false Turbo Motor Driver*1 or ECM*2 5.844,1.521 6.375,2.292 0.531,0.771 10 false ECM*1 3.052,3.052 7.063,3.344 4.01,0.292 10 false *1: Except models compliant with EURO 5 emission regulations 3.073,3.406 6.76,3.76 3.688,0.354 10 false *2: Models compliant with EURO 5 emission regulations



c.

Operation

i.

At Engine Low Speed Range

When the engine is running in a low speed range, the DC motor pulls up the linkage by a signal from the turbo motor driver*1 or ECM*2. The tip of the linkage rotates the unison ring counterclockwise through a drive arm. The unison ring contains a driven arm, which is placed through the cutout portion of the unison ring. This driven arm also moves in the direction of the rotation of the unison ring. The fulcrum of the driven arm is an axis that is integrated with the nozzle vane behind the plate. When the driven arm moves counterclockwise, the nozzle vane moves toward the closing direction. This results in increasing the velocity of the exhaust gas flowing to the turbine, as well as the speed of the turbine. As a result, torque is improved when the engine is running at low speeds.

*1: Except models compliant with EURO 5 emission regulations

*2: Models compliant with EURO 5 emission regulations



W133171C01
1.219,0.844 0.99,0.448 true 1.927,0.677 1.771,0.896 true 1.865,2.417 1.635,2.021 true 3.229,2.385 3.469,1.938 true 3.396,0.948 3.271,0.51 true 3.531,0.781 3.521,0.365 true 3.802,2.563 3.896,2.375 true 4.75,0.99 4.708,0.563 true 4.688,0.99 4.427,0.823 true 4.938,1.125 5.052,0.271 true 6.094,1.385 6.208,0.531 true 5.458,2.531 5.365,2.167 true 3.563,1.01 3.969,0.5 true 6.51,2.24 6.281,2.052 true 0.854,0.271 1.167,0.427 0.313,0.156 10 false *1 1.844,2.458 2.156,2.615 0.313,0.156 10 false *2 3.427,0.167 3.74,0.323 0.313,0.156 10 false *3 3.646,2.552 3.958,2.708 0.313,0.156 10 false *4 4.615,0.354 4.927,0.51 0.313,0.156 10 false *5 6.156,0.333 6.469,0.49 0.313,0.156 10 false *6 1.917,0.469 2.229,0.625 0.313,0.156 10 false *a 4.26,0.708 4.573,0.865 0.313,0.156 10 false *b 3.104,2.427 3.417,2.583 0.313,0.156 10 false *2 3.125,0.323 3.438,0.479 0.313,0.156 10 false *1 4.979,0.073 5.292,0.229 0.313,0.156 10 false *c 5.406,2.573 5.719,2.729 0.313,0.156 10 false *3 4.021,0.406 4.333,0.563 0.313,0.156 10 false *5 6.573,2.24 6.885,2.396 0.313,0.156 10 false *4
*1 Nozzle Vane *2 Plate
*3 Unison Ring *4 Linkage
*5 Driven Arm *6 Drive Arm
*a Gas Flow *b Cutout Portion
*c Fulcrum - -



ii.

At Engine Medium-to-High Speed Range

When the engine is running in a medium-to-high speed range, the DC motor presses down the linkage by a signal from the turbo motor driver*1 or ECM*2. With this, the driven arm moves clockwise and this opens the nozzle vane and holds the specified supercharging pressure. Thus, lowering the back pressure and improving the output and fuel consumption.

*1: Except models compliant with EURO 5 emission regulations

*2: Models compliant with EURO 5 emission regulations



W133172




Fuel Pump Control


a.

The ECM operates the fuel pump in accordance with signals from the meter ECU, which indicate the fuel amount in the fuel tanks (calculated by signals from fuel sender gauges in each fuel tank), to transfer fuel from the fuel sub tank sub-assembly to the fuel tank sub-assembly using the jet pump for fuel transfer.


b.

The meter ECU determines if the fuel pump control system is malfunctioning based on the fuel amount in the fuel tank sub-assembly and fuel sub tank sub-assembly. When the meter ECU detects that the fuel amount in the fuel tank sub-assembly is small (20.7 liters [21.9 US qts, 18.2 Imp. qts] or less) and the amount in the fuel sub tank sub-assembly is large (7.8 liters [8.2 US qts, 6.9 Imp. qts] or more), it determines that fuel has not been transferred from the fuel sub tank sub-assembly to the fuel tank sub-assembly. The meter ECU then blinks the low fuel warning light in the combination meter to inform the driver of the fuel pump control system malfunction. In addition, the master warning light comes on, the buzzer sounds and the warning message (Check Fuel System) is displayed on the multi-information display on models with optitron display type combination meter.

W133173E01
3.188,2.24 3.188,1.917 3.188,1.917 3.479,1.917 true 1.573,2.094 2.76,2.396 1.188,0.302 10 false Meter ECU 0.292,2.854 1.875,3.708 1.583,0.854 10 false Fuel Sender Gauge (for Fuel Tank Sub-assembly) 1.979,2.854 3.542,3.729 1.563,0.875 10 false Fuel Sender Gauge (for Fuel Sub Tank Sub-assembly) 3.542,1.823 4.427,2.146 0.885,0.323 10 false CAN (V Bus) 3.135,2.458 4.438,2.802 1.302,0.344 10 false Fuel Amount Signal 4.24,0.365 5.271,0.719 1.031,0.354 10 false EFI Main Relay 6.156,0.385 7.052,0.74 0.896,0.354 10 false Battery 6.156,1.052 7.042,1.833 0.885,0.781 10 false Fuel Pump Relay 6.188,2.385 7.073,3.167 0.885,0.781 10 false Fuel Pump 4.625,1.615 5.125,2.115 0.5,0.5 10 false ECM 0.844,0.344 2.083,0.646 1.24,0.302 10 false Combination Meter



EGR Control


a.

This system is designed to reduce and control NOx formation due to a slight reduction of peak temperature in the engine combustion chamber, which is accomplished by introducing a small amount of inert gas into intake manifold.


b.

By sensing the engine driving conditions and actual amount of the EGR valve opening, the ECM operates the EGR valve and diesel throttle control motor, and regulates the amount of exhaust gas.

System Diagram
W133174C01
0.49,1.75 0.906,1.604 true 0.896,2.042 1.135,1.635 true 1.281,2.563 1.594,2.375 true 1.583,0.604 1.99,0.917 true 3.542,0.906 3.823,0.635 true 4.281,1.469 4.188,1.208 true 4.552,1.594 4.563,1.323 true 3.875,2.458 4.167,2.552 true 0.313,1.719 0.625,1.875 0.313,0.156 10 false *1 0.813,2.083 1.125,2.24 0.313,0.156 10 false *2 1.083,2.5 1.396,2.656 0.313,0.156 10 false *3 1.385,0.51 1.698,0.667 0.313,0.156 10 false *4 4.063,1.021 4.375,1.177 0.313,0.156 10 false *5 5.271,1.406 5.583,1.563 0.313,0.156 10 false *6 5.24,3.104 5.708,3.26 0.469,0.156 10 false *7 6.292,0.969 6.76,1.125 0.469,0.156 10 false *8 6.271,1.385 6.74,1.542 0.469,0.156 10 false *9 6.292,1.833 6.76,1.99 0.469,0.156 10 false *10 6.313,2.25 6.781,2.406 0.469,0.156 10 false *11 6.292,2.698 6.76,2.854 0.469,0.156 10 false *12 6.281,3.104 6.75,3.26 0.469,0.156 10 false *13 3.875,0.552 4.188,0.708 0.313,0.156 10 false *4 4.469,1.146 4.781,1.302 0.313,0.156 10 false *1 4.219,2.479 4.531,2.635 0.313,0.156 10 false *3
*1 EGR Valve Position Sensor *2 No. 1 EGR Valve
*3 EGR Cooler *4 Diesel Throttle Control Motor
*5 No. 2 EGR Valve *6 ECM
*7 Atmospheric Pressure Sensor *8 Accelerator Pedal Sensor Assembly
*9 Crank Position Sensor *10 Intake Mass Air Flow Meter sub-assembly
*11 Engine Coolant Temperature Sensor *12 Atmospheric Temperature Sensor
*13 Manifold Absolute Pressure Sensor - -
V100135

Exhaust Gas
V100136

Intake Air




Engine Mounting Control


a.

General

i.

When the engine speed and the vehicle speed are low, this engine mounting utilizes the vacuum from the vacuum pump to move the diaphragm inside the mount, which switches the passage for the fluid sealed in the fluid chambers. By softening the damping characteristics of the mounting in this manner, the mounting restrains the engine vibration.

W133175C01
2.052,1.552 2.385,1.771 true 3.271,1.76 3.531,1.552 true 2.469,0.625 2.781,0.781 0.313,0.156 10 false *1 3.281,0.708 3.594,0.865 0.313,0.156 10 false *2 1.865,1.427 2.177,1.583 0.313,0.156 10 false *3 3.802,0.688 4.115,0.844 0.313,0.156 10 false *4 4.708,0.698 5.021,0.854 0.313,0.156 10 false *5 5.427,0.563 5.74,0.719 0.313,0.156 10 false *6 5.396,0.844 5.708,1 0.313,0.156 10 false *7 3.521,1.417 3.833,1.573 0.313,0.156 10 false *3
*1 Engine *2 Vacuum Pump
*3 Electrical Hydraulic Type Engine Mounting *4 VSV
*5 ECM *6 Vehicle Speed Signal
*7 Crank Position Sensor - -




b.

Construction

i.

This engine mounting consists primarily of the rubber portion, No. 1 fluid chamber, No. 2 fluid chamber, and diaphragm. Fluid is sealed in the No. 1 and No. 2 fluid chambers.


ii.

This engine mounting obtains a vacuum from the vacuum pump via the VSV. It utilizes the vacuum to pull the diaphragm down in order to open or close the passages that connect the No. 1 and No. 2 fluid chambers.


iii.

The No. 1 and No. 2 fluid chambers use two fluid passages: the No. 1 fluid passage that is always connected regardless of whether the diaphragm is open or closed; and the No. 2 fluid passage that is connected only when the diaphragm is open. The fluid flows back and forth between the No. 1 and No. 2 fluid chambers through these two passages in order to restrain the vibration.

W133176C01
2.323,1.406 3.198,1.896 true 3.354,2.906 2.646,3.198 true 4.052,2.313 4.781,2.531 true 2.396,2.708 3.042,2.5 true 3.698,2.438 2.313,1.865 true 4.063,2.708 4.792,2.927 true 2.167,1.313 2.479,1.469 0.313,0.156 10 false *1 2.51,3.156 2.823,3.313 0.313,0.156 10 false *2 2.125,1.792 2.438,1.948 0.313,0.156 10 false *a 2.208,2.635 2.521,2.792 0.313,0.156 10 false *b 3.51,3.302 3.823,3.458 0.313,0.156 10 false *c 4.833,2.865 5.146,3.021 0.313,0.156 10 false *d 4.844,2.448 5.156,2.604 0.313,0.156 10 false *e 5.354,0.542 5.667,0.74 0.313,0.198 10 false : *f
*1 Rubber *2 Diaphragm
*a No.2 Fluid Passage *b No. 1 Fluid Passage
*c Vacuum Intake *d No. 2 Fluid Chamber
*e No. 1 Fluid Chamber *f Fluid




c.

Operation

i.

General

·

When the ECM determines that the engine speed and the vehicle speed are low, it controls the introduction of vacuum from the vacuum pump to the engine mounting by turning the VSV ON or OFF.

·

A hysteresis is provided for both the engine speed and the vehicle speed at the point in which the VSV switches from ON to OFF.

·

While the engine is cranking, the VSV is OFF.


W133177E01
2.094,0.01 3.396,0.26 1.302,0.25 10 false Vehicle Speed 4.635,1.958 5.521,2.26 0.885,0.302 10 false Engine Speed 1.729,1.25 2.469,1.646 0.74,0.396 10 false Low Speed 2.74,2.292 3.479,2.688 0.74,0.396 10 false Low Speed 0.594,0.521 1.688,0.927 1.094,0.406 10 false : VSV ON 0.583,0.146 1.698,0.458 1.115,0.313 10 false : VSV OFF


ii.

When the VSV is OFF

·

When the ECM determines that the engine speed and vehicle speed exceed the specified value, it stops the introduction of vacuum into the engine mounting by turning the VSV OFF.

·

When no vacuum is introduced into the engine mounting, the diaphragm does not move, so the No. 1 fluid passage remains closed. In this state, the fluid passes only through the No. 1 fluid passage in order to flow back and forth between the No. 1 and No. 2 fluid chambers.


W133178C01
3.74,2.135 4.25,2.302 true 3.906,1.781 4.635,1.552 true 3.479,2.521 3.792,2.677 0.313,0.156 10 false *a 4.688,1.469 5,1.625 0.313,0.156 10 false *c 4.313,2.25 4.625,2.406 0.313,0.156 10 false *b
*a No Vacuum Introduced *b Diaphragm Stopped
*c Flow of Fluid in No. 1 Fluid Passage - -



iii.

When the VSV is ON

·

When the ECM determines that the engine speed and the vehicle speed are equal to or less than the specified value, it turns the VSV ON to introduce vacuum into the engine mounting.

·

When a vacuum is introduced into the engine mounting, it pulls the diaphragm down, causing the No. 2 fluid passage to open. As a result, a large volume of fluid flows back and forth between the No. 1 and No. 2 fluid chambers, thus minimizing the fluid resistance and softening the engine mounting characteristics.


W133179C01
2.625,2.104 3.552,2.208 true 3.917,1.813 4.49,1.615 true 3.719,1.771 4.469,1.24 true 2.448,2 2.76,2.156 0.313,0.156 10 false *a 3.51,2.635 3.823,2.792 0.313,0.156 10 false *b 4.552,1.531 4.865,1.688 0.313,0.156 10 false *c 4.5,1.146 4.813,1.302 0.313,0.156 10 false *d
*a Diaphragm Descends *b Vacuum Introduced
*c Flow of Fluid in No. 1 Fluid Passage *d Flow of Fluid in No. 2 Fluid Passage





Oil Maintenance Management System


a.

General

i.

In this oil maintenance management system, the soot volume in the engine oil is calculated based on the engine operating conditions. Based on the calculated soot volume, the ECM displays an "Oil Maintenance Reqd" warning on the multi-information display to inform the driver when it is necessary to change the engine oil.


ii.

The ECM calculates soot volume from the injection volume, injection timing and intake air volume in order to operate this system.

System Diagram
W133180E01
4.323,3.292 4,1.75 4,1.75 3.635,1.75 true 4.469,0.552 6.542,0.917 2.073,0.365 10 false Combination Meter 4.719,0.969 6.385,1.354 1.667,0.385 10 false Multi-information Display 0.656,2.365 1.156,2.635 0.5,0.271 10 false ECM 0.865,2.76 2.094,3.094 1.229,0.333 10 false - Injection Volume 0.844,3.146 2.073,3.479 1.229,0.333 10 false - Injection Timing 0.823,3.552 2.052,3.885 1.229,0.333 10 false - Intake Air Volume 2.75,2.958 3.75,3.667 1,0.708 10 false Calculation of Soot Volume 2.792,1.677 3.74,2.031 0.948,0.354 10 false CAN (V Bus) 5.156,3.156 6.104,3.51 0.948,0.354 10 false Meter ECU 4.969,3.938 6.281,4.281 1.313,0.344 10 false ODO/TRIP Switch

HINT:

Since this system is controlled based on engine operating conditions, the "Oil Maintenance Reqd" warning may be displayed before driving 30000 km (the maximum travel distance after oil maintenance). If the "Oil Maintenance Reqd" warning is displayed, immediately replace the oil and oil filter.




b.

Soot Volume Calculation Method

i.

The soot volume largely depends on injection ending timing and air fuel ratio. The ECM calculates soot volume from this information as shown in the graphs below.

W102262E04
2.896,2.219 4.792,2.604 1.896,0.385 10 false Calculation of Air Fuel Ratio 2.969,4.927 4.49,5.333 1.521,0.406 10 false Injection Ending Timing 2.156,0.573 2.573,0.865 0.417,0.292 10 false Large 2.188,1.833 3.042,2.24 0.854,0.406 10 false Large (Lean) 2.156,1.417 2.583,1.802 0.427,0.385 10 false Small 2.135,3.271 2.563,3.656 0.427,0.385 10 false Large 2.146,4.24 2.573,4.625 0.427,0.385 10 false Small 4.552,1.854 5.354,2.167 0.802,0.313 10 false Small (Rich) 2.615,4.646 2.979,5.031 0.365,0.385 10 false Early 4.552,4.677 4.906,5.063 0.354,0.385 10 false Late 1.01,1.042 1.906,1.302 0.896,0.26 10 false Soot Volume 1.125,3.802 2.021,4.063 0.896,0.26 10 false Soot Volume

HINT:

The accumulated soot volume memorized in ECM can be reset using the following procedures.

1.

Switch the power source to IG-ON. Then, use the ODO/TRIP switch to turn ON the "TRIP A" display on the multi-information display.

2.

Switch the power source to OFF. While pushing the ODO/TRIP switch, switch the power source to IG-ON.

3.

With the power source in the IG-ON mode, keep holding the ODO/TRIP switch (for at least five seconds) with the multi-information display counting down as shown below.

4.

When the resetting is completed, the multi-information display will display "COMPLETE" for one second and the buzzer built into the combination meter will sound.


W133181E01
1.625,5.427 1.823,5.427 1.823,5.427 1.885,5.094 true 1.229,0.823 2.344,1.188 1.115,0.365 10 false 5 seconds before 3.063,0.823 4.177,1.188 1.115,0.365 10 false 4 seconds before 4.885,0.823 6,1.188 1.115,0.365 10 false 3 seconds before 1.188,2.125 2.302,2.49 1.115,0.365 10 false 2 seconds before 3.031,2.135 4.146,2.5 1.115,0.365 10 false 1 second before 4.885,2.125 6,2.49 1.115,0.365 10 false Reset complete 0.479,5.375 1.75,5.719 1.271,0.344 10 false ODO/TRIP Switch





Catalyst Support Control


a.

General

i.

In order to comply with emission regulations, a Diesel Particulate Filter (DPF) catalyst is used to effectively collect and purify CO, HC and Particulate Matter (PM) contained in exhaust gas.


ii.

Due to the use of the DPF, catalyst support control that combusts and purges PM accumulated in the DPF is used for DPF regeneration.

W133182C01
1.563,0.781 1.365,0.552 true 5.813,0.49 5.573,0.792 true 2.5,1.854 1.875,1.958 true 5.302,1.938 4.594,1.875 true 1.635,1.917 1.385,2.094 true 1.646,1.906 1.396,2.083 true 5.656,2.042 5.5,1.927 true 0.927,3.729 0.625,3.646 true 6.521,3.604 6.219,3.719 true 0.948,4.917 0.646,4.833 true 6.542,4.771 6.24,4.885 true 1.188,0.385 1.5,0.542 0.313,0.156 10 false *1 2.552,1.771 2.865,1.927 0.313,0.156 10 false *3 2.615,2.094 2.927,2.25 0.313,0.156 10 false *4 4.344,2.104 4.656,2.26 0.313,0.156 10 false *5 0.438,3.563 0.698,3.74 0.26,0.177 10 false *6 1.323,3.281 1.635,3.438 0.313,0.156 10 false *7 5.583,3.302 5.896,3.458 0.313,0.156 10 false *9 5.531,3.802 6,3.958 0.469,0.156 10 false *10 0.385,4.74 0.667,4.938 0.281,0.198 10 false *11 1.781,4.906 2.25,5.063 0.469,0.156 10 false *12 0.573,5.333 1.042,5.49 0.469,0.156 10 false *13 1.271,5.573 1.74,5.729 0.469,0.156 10 false *14 1.708,0.51 2.021,0.667 0.313,0.156 10 false *a 5.208,0.49 5.521,0.646 0.313,0.156 10 false *b 5.031,0.781 5.344,0.938 0.313,0.156 10 false *1 5.781,0.323 6.094,0.479 0.313,0.156 10 false *1 1.219,2.104 1.531,2.26 0.313,0.156 10 false *2 4.344,1.76 4.656,1.917 0.313,0.156 10 false *3 5.698,2.052 6.01,2.208 0.313,0.156 10 false *2 6.583,3.531 6.844,3.708 0.26,0.177 10 false *6 1.292,3.781 1.604,3.938 0.313,0.156 10 false *8 6.563,4.656 6.844,4.854 0.281,0.198 10 false *11 5.104,4.896 5.365,5.073 0.26,0.177 10 false *15 6.375,5.292 6.635,5.469 0.26,0.177 10 false *16 3.458,3.844 3.719,4.021 0.26,0.177 10 false *18 3.427,5.75 3.688,5.927 0.26,0.177 10 false *19 2.375,6.802 2.635,6.979 0.26,0.177 10 false *20 3.458,7.188 3.719,7.365 0.26,0.177 10 false *21 4.583,6.781 4.844,6.958 0.26,0.177 10 false *22 5.719,5.542 5.979,5.719 0.26,0.177 10 false *17
*1 Cylinder Head *2 Exhaust Fuel Addition Injector Assembly
*3 Injector Assembly *4 No. 2 Injector Driver
*5 No. 1 Injector Driver *6 Oxidation Catalyst
*7 Exhaust Gas Temperature Sensor (Bank 2, Sensor 1) *8 Exhaust Gas Temperature Sensor (Bank 2, Sensor 2)
*9 Exhaust Gas Temperature Sensor (Bank 1, Sensor 1) *10 Exhaust Gas Temperature Sensor (Bank 1, Sensor 2)
*11 DPF *12 Differential Pressure Sensor (Bank 2)
*13 Exhaust Gas Temperature Sensor (Bank 2, Sensor 3) *14 Air Fuel Ratio Sensor (Bank 2)
*15 Differential Pressure Sensor (Bank 1) *16 Exhaust Gas Temperature Sensor (Bank 1, Sensor 3)
*17 Air Fuel Ratio Sensor (Bank 1) *18 ECM
*19 Atmospheric Pressure Sensor *20 Intake Mass Air Flow Meter Sub-assembly
*21 DPF Switch *22 Engine Coolant Temperature Sensor
*a LH *b RH




b.

Function

i.

When an extremely large amount of PM is accumulated in the DPF, the back pressure of the engine increases and the PM is combusted at once, potentially damaging the filter. In order to prevent that, it is necessary to forcibly combust the accumulated PM. Therefore, the accumulated PM is combusted by increasing the temperature of the filter.


ii.

If the temperature of the DPF does not increase and the PM keeps accumulating in the DPF, a message is displayed on the multi-information display*1 or the DPF warning light*2 illuminates or blinks to notify the driver.


iii.

The amount of accumulated PM is displayed on the DPF indicator in the multi-information display in the combination meter assembly. *1 The amount of accumulated PM is displayed on the DPF indicator in the combination meter assembly.*2.

*1: Models with multi-information display

*2: Models without multi-information display




c.

Operation

i.

In order to regenerate the DPF, the temperature of the DPF is increased to combust the accumulated PM in the DPF, expelling it as CO2 and H2O.


ii.

The ECM monitors the engine condition and calculates the total amount of accumulated PM. In addition, the ECM calculates the amount of combusted PM according to the engine speed, fuel injection volume and the injection volume of the exhaust fuel addition injector assembly. The amount of accumulated PM in the DPF is calculated based on the calculated total amount of accumulated PM and the amount of combusted PM. The ECM urges the driver to perform PM automatic or manual regeneration according to the level of accumulated PM.


iii.

When automatic or manual regeneration is performed, the injection of the exhaust fuel addition injector assembly and the engine combustion condition are controlled, increasing the temperature of the DPF. As a result, the temperature of the DPF becomes approximately 600°C to 700°C and PM is combusted.


iv.

When the vehicle is continuously driven with a high exhaust temperature such as at high speeds, the temperature of the DPF is sufficiently increased and PM is spontaneously combusted. At this time, no special control such as exhaust fuel addition injector assembly control, etc. is performed.


v.

When the vehicle is continuously driven while the temperature of the DPF is not high enough for PM combustion such as when driving for a short distance or driving for a short time, catalyst performance is decreased. As a result, PM is accumulated in the DPF. When the amount of accumulated PM exceeds the threshold (for automatic regeneration), the ECM performs automatic regeneration until the amount of PM reaches zero.


vi.

If the vehicle continues to be driven for a short distance even after automatic regeneration is performed, more PM is accumulated. When the amount of accumulated PM exceeds the threshold (for manual regeneration), a message is displayed on the multi-information display*1 or the DPF*2 warning light illuminates or blinks to urge the driver to perform manual regeneration.

*1: Models with multi-information display

*2: Models without multi-information display



vii.

Automatic Regeneration

When automatic regeneration is being performed, the ECM controls the fuel injection of the exhaust fuel addition injector assembly and the engine combustion condition, increasing the temperature of the DPF to combust the PM. Idle up is performed while the vehicle is stopped.

HINT:

The end of automatic regeneration is calculated by the ECM according to the amount of accumulated PM.




viii.

Manual Regeneration

1.

The following methods are used to perform manual regeneration. For details of manual regeneration operation, refer to the Repair Manual.

(a)

DPF Switch Operation Method

Stop the vehicle and press the DPF switch to perform manual regeneration.

HINT:

Operating the accelerator pedal or moving the shift lever to a position other than P and N while regeneration is being performed temporarily stops regeneration.



(b)

Global TechStream (GTS) Operation Method

Stop the vehicle and operate the Global TechStream (GTS) to perform manual regeneration.



2.

When manual regeneration is being performed, the ECM controls the fuel injection of the exhaust fuel addition injector assembly and the engine combustion condition and performs idle up, increasing the temperature of the DPF to combust the PM.

HINT:

The end of manual regeneration is calculated by the ECM according to the amount of accumulated PM.




ix.

Fail-safe

If manual regeneration is performed when the amount of accumulated PM is beyond the threshold, the DPF may get damaged. Therefore, when the amount of accumulated PM exceeds the threshold (for the fail-safe function), the injection volume is controlled to a minimum level to cancel regeneration control. As a result, manual regeneration cannot be performed properly. At the same time, the MIL illuminates and a message is displayed on the multi-information display*1 or the DPF warning light*2 blinks to notify the driver of a malfunction.

Relationship between DPF Indicator, MIL, Message on Multi-information Display*1, DPF Warning Light*2 and Regeneration Control (Conceptual Diagram)
W138767E01
2.313,3.688 2.542,3.688 2.542,3.688 2.615,3.073 true 0.531,0.052 2.219,0.344 1.688,0.292 10 false : Automatic regeneration 3.688,0.052 5.375,0.344 1.688,0.292 10 false : Manual regeneration 0.052,1.677 0.927,2.573 0.875,0.896 10 false PM Accumulation 0.958,1.042 2.448,1.344 1.49,0.302 10 false Threshold (for Fail-safe) 1.125,2.146 2.469,2.677 1.344,0.531 10 false Threshold (for Manual Regeneration) 1,2.719 2.573,3.323 1.573,0.604 10 false Threshold (for Automatic Regeneration) 2.625,0.781 4.458,1.115 1.833,0.333 10 false Fail-safe Range 2.573,1.177 4.406,1.51 1.833,0.333 10 false Manual Regeneration Range 2.552,2.281 4.021,2.771 1.469,0.49 10 false Automatic Regeneration Range 0.667,3.583 2.26,3.896 1.594,0.313 10 false Normal Operation Range 6.635,3.01 6.792,3.208 0.156,0.198 10 false A 6.635,2.458 6.792,2.656 0.156,0.198 10 false B 6.635,1.885 6.792,2.083 0.156,0.198 10 false C 6.635,1.302 6.792,1.5 0.156,0.198 10 false D 6.635,0.906 6.792,1.104 0.156,0.198 10 false E 3.99,3.396 5.427,3.927 1.438,0.531 10 false Traveled Distance

Text in Illustration DPF Indicator Display MIL DPF Warning Light*2 Massage on Multi-information Display*1
A 0 to 2 - - -
B 3 to 6 - - -
C 7 to 8 - Illuminate DPF FULL SEE OWNER'S MANUAL
D 9 - Blink DPF FULL ENGINE SERVICE REQUIRED
E 10 Illuminate Blink DPF FULL ENGINE SERVICE REQUIRED

*1: Models with multi-information display

*2: Models without multi-information display



W138313C01
2.104,1.552 1.271,0.76 true 5.094,1.552 4.698,1.167 true 0.448,0.063 0.771,0.292 0.323,0.229 12 false *A: 4,0.052 4.323,0.25 0.323,0.198 12 false *B: 2.01,0.583 2.323,0.74 0.313,0.156 10 false *1 1.094,0.594 1.406,0.75 0.313,0.156 10 false *3 0.51,2.24 0.823,2.396 0.313,0.156 10 false *4 4.813,0.573 5.125,0.729 0.313,0.156 10 false *1 5.552,0.563 6.073,0.854 0.521,0.292 10 false *2 (*C) 4.49,0.948 5.031,1.156 0.542,0.208 10 false *3 (*D) 6.542,2.229 6.854,2.385 0.313,0.156 10 false *4 3.49,1.479 3.99,1.677 0.5,0.198 10 false *5 (*D) 3.5,2.365 4,2.563 0.5,0.198 10 false *6 (*C)
*A LHD Models *B RHD Models
*C Models without Multi-information Display *D Models with Multi-information Display
*1 MIL *2 DPF Warning Light
*3 Multi-information Display *4 DPF Switch
*5 DPF Indicator (Displayed on Multi-information Display) *6 DPF Indicator (Displayed on Odometer/trip Meter)





Diagnosis


a.

When the ECM detects a malfunction, the ECM makes a diagnosis and memorizes the failed section. Furthermore, the MIL in the combination meter illuminates or blinks to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Code (DTC) of the malfunctions. The DTC can be accessed by using the Global TechStream (GTS).


c.

For details, refer to the Repair Manual.

HINT:

To clear the DTC that is stored in the ECM, use the Global TechStream (GTS), disconnect the battery terminal or remove the EFI MAIN fuse for 1 minute or longer.




Fail-safe


a.

When a malfunction is detected at any of the sensors, there is a possibility of an engine or other malfunction occurring if the ECM were to continue to control the engine control system in the normal way. To prevent such a problem, the fail-safe function of the ECM either relies on the data stored in memory to allow the engine control system to continue operating, or stops the engine if a hazard is anticipated. For details, refer to the Repair Manual.