Home › General › CHASSIS › TRANSFER
NM2660E _V1 General _054360 CHASSIS _0267095 TRANSFER UN GENERAL/CONTROL/DETAILS F

CHASSIS  TRANSFER  GENERAL/CONTROL/DETAILS  CONSTRUCTION  


GENERAL


a.

The construction of the JF2A transfer is shown below.

i.

A planetary gear unit is used in the reduction mechanism and a silent chain is used to reduce front drive noise.


ii.

A lever type synchromesh mechanism is used for the H4-L4 switching section to eliminate gear clash when switching from H4-L4.


iii.

For the JF2A transfer, a transfer shift actuator that has 2 built-in shift motors is used. As a result, switching from H4-L4 can be performed independently using the shift motors, achieving a simple shift actuation mechanism. This enhances efficiency of power transfer and durability of the shift mechanism.

X132305C01
2.802,1.135 2.646,0.281 true 1.479,0.531 2.167,0.927 true 1.042,2.198 1.708,1.448 true 1.719,3.042 3.156,2.385 true 2.229,4.01 3.052,3.625 true 5.146,3.948 4.104,3.01 true 5.385,2.365 5.875,2.073 true 5.031,1.448 5.552,1.167 true 3.615,2.354 5.115,0.49 true 2.531,0.073 2.781,0.302 0.25,0.229 10 false *1 1.313,0.385 1.531,0.656 0.219,0.271 10 false *2 0.927,2.198 1.198,2.438 0.271,0.24 10 false *3 1.542,2.948 1.74,3.198 0.198,0.25 10 false *4 2.052,3.938 2.26,4.208 0.208,0.271 10 false *5 5.167,3.938 5.396,4.188 0.229,0.25 10 false *6 5.906,1.958 6.177,2.229 0.271,0.271 10 false *7 5.573,1.052 5.771,1.302 0.198,0.25 10 false *8 5.125,0.344 5.333,0.594 0.208,0.25 10 false *9
*1 Lever Type Synchromesh Mechanism *2 Transfer Low Planetary Gear Assembly
*3 Transfer Input Shaft *4 Transfer Gear Shift Fork No. 2
*5 Front Transfer Output Shaft *6 Silent Chain
*7 Transfer Shift Actuator Assembly *8 Rear Transfer Output Shaft
*9 Transfer Gear Shift Fork No. 1 - -





PLANETARY GEAR UNIT


a.

General

i.

The transfer low planetary gear assembly consists of the planetary sun gear, 6 planetary pinion gears, planetary ring gear, and planetary carrier.

·

The planetary sun gear is integrated with the transfer input shaft.

·

6 planetary pinion gears are fitted to the planetary carrier. Each pinion gear shaft is fixed to the planetary carrier. A planetary spline piece is fitted to the rear of the planetary carrier.

·

The planetary ring gear is fixed to the front transfer case and its internal teeth mesh with the planetary pinion gears.

·

In this planetary gear unit, the power transmission route is switched in accordance with the movement of the transfer high and low clutch sleeve. The input power from the transfer input shaft is transmitted to the differential case via the high and low clutch sleeve.


X132306C01
3.125,0.771 2.99,0.406 true 2.135,0.844 2.75,1.208 true 1.708,2.448 2.302,2.125 true 3.167,3.302 3.521,2.719 true 4.354,3.156 3.49,2.281 true 5.375,2.792 4.479,2.344 true 4.469,1.271 5.5,1.427 true 3.219,1.073 3.719,0.385 3.719,0.385 3.729,1.031 true 2.875,0.229 3.146,0.438 0.271,0.208 10 false *1 1.969,0.708 2.24,1 0.271,0.292 10 false *2 1.531,2.385 1.729,2.625 0.198,0.24 10 false *3 3.052,3.292 3.344,3.563 0.292,0.271 10 false *4 4.375,3.156 4.646,3.438 0.271,0.281 10 false *5 5.406,2.719 5.698,3 0.292,0.281 10 false *6 5.531,1.333 5.792,1.594 0.26,0.26 10 false *7 3.677,0.188 3.927,0.438 0.25,0.25 10 false *8
*1 Transfer Low Planetary Ring Gear *2 Pinion Shaft
*3 Transfer Input Shaft *4 Planetary Pinion Gear
*5 Planetary Sun Gear *6 Planetary Spline Piece
*7 Transfer High and Low Clutch Sleeve *8 Planetary Carrier




b.

H4 Position

i.

In the H (H4) position, the splines at the rear of the transfer input shaft mesh with the internal gear teeth of the high and low clutch sleeve.


ii.

Also, the transfer high and low clutch sleeve is meshed to the differential case. Thus, the rotation of the input shaft is transmitted to the transfer high and low clutch sleeve, the differential case.

X132307C01
1.177,0.615 1.979,0.885 true 2.188,0.99 1.844,0.469 true 2.375,0.917 2.375,0.302 true 2.875,0.917 3.146,0.49 true 3.208,1.031 3.563,0.75 true 2.719,2.094 3.073,1.219 true 1.302,2.208 1.156,1.802 true 4.521,2.052 4.802,1.625 true 5.521,0.802 5.219,0.406 true 5.979,1.125 6.313,0.708 true 5.969,2.417 5.594,1.708 true 1.708,0.292 1.948,0.51 0.24,0.219 10 false *1 0.979,0.479 1.177,0.698 0.198,0.219 10 false *2 1.26,2.219 1.531,2.417 0.271,0.198 10 false *3 2.604,2.094 2.854,2.344 0.25,0.25 10 false *4 3.583,0.604 3.813,0.854 0.229,0.25 10 false *5 3.115,0.292 3.333,0.542 0.219,0.25 10 false *6 2.302,0.104 2.542,0.313 0.24,0.208 10 false *7 5.083,0.208 5.396,0.458 0.313,0.25 10 false *8 4.406,2.052 4.646,2.302 0.24,0.25 10 false *9 5.906,2.417 6.24,2.667 0.333,0.25 10 false *10 6.313,0.521 6.594,0.813 0.281,0.292 10 false *11
*1 Planetary Pinion Gear *2 Transfer Low Planetary Ring Gear
*3 Transfer Input Shaft *4 Differential Case
*5 Transfer High and Low Clutch Sleeve *6 Planetary Spline Piece
*7 Planetary Carrier *8 Transfer Low Planetary Pinion Gear
*9 Planetary Ring Gear *10 Planetary Sun Gear (Input Shaft)
*11 Planetary Carrier (Pinion Shaft) - -




c.

L4 Position

i.

In the L (L4) position, the external teeth of the transfer high and low clutch sleeve are meshed with the planetary spline piece.


ii.

Thus, the rotation of the transfer input shaft is transmitted in a reduced form to the planetary sun gear, planetary pinion gear, planetary pinion gear shaft, planetary carrier, planetary spline piece, transfer high and low clutch sleeve, and differential case.

X132308C01
1.073,0.708 2.01,0.875 true 2.208,1.031 1.865,0.396 true 2.385,0.906 2.385,0.292 true 2.875,0.927 3.167,0.417 true 3.406,1.063 3.74,0.635 true 2.823,1.99 3.083,1.219 true 1.406,2.26 1.25,1.802 true 5.5,0.813 5.281,0.333 true 4.5,1.948 4.792,1.604 true 5.885,2.333 5.573,1.656 true 5.979,1.135 6.344,0.688 true 1.729,0.208 1.938,0.396 0.208,0.188 10 false *1 0.896,0.594 1.156,0.885 0.26,0.292 10 false *2 1.365,2.25 1.667,2.49 0.302,0.24 10 false *3 2.708,1.99 2.99,2.219 0.281,0.229 10 false *4 3.74,0.49 3.979,0.781 0.24,0.292 10 false *5 3.156,0.26 3.385,0.531 0.229,0.271 10 false *6 2.313,0.094 2.563,0.323 0.25,0.229 10 false *7 5.167,0.156 5.458,0.375 0.292,0.219 10 false *8 4.385,1.948 4.677,2.208 0.292,0.26 10 false *9 5.781,2.333 6.198,2.552 0.417,0.219 10 false *10 6.313,0.49 6.635,0.719 0.323,0.229 10 false *11
*1 Planetary Pinion Gear *2 Transfer Low Planetary Ring Gear
*3 Transfer Input Shaft *4 Differential Case
*5 Transfer High and Low Clutch Sleeve *6 Planetary Spline Piece
*7 Planetary Carrier *8 Transfer Low Planetary Pinion Gear
*9 Planetary Ring Gear *10 Planetary Sun Gear (Input Shaft)
*11 Planetary Carrier (Pinion Shaft) - -





CENTER DIFFERENTIAL (TORSEN LSD)


a.

General

i.

The center differential uses a TORSEN LSD (Limited Slip Differential).


ii.

The TORSEN LSD is a torque-sensing LSD. It generates a limited-differential torque in proportion to the drive torque, and instantly changes the front and rear torque distribution.


iii.

The torque distribution during straightline driving is 40/60 (front/rear), which is helpful for an appropriate steering response during the initial stage of a turn. During the acceleration stage of a turn, the torque distribution increases the rear wheels.


iv.

This center differential consists of a center differential case, coupling, ring gear, 8 pinion gears, sun gear, and planetary carrier.

X132309C01
1.906,1.344 3.208,1.635 true 2.156,0.927 3.26,1.302 true 3.385,1.073 2.75,0.656 true 3.76,1.563 3.5,0.365 true 3.927,1.167 4.521,0.302 true 4.156,1.771 5.885,2.448 true 5.25,2.729 4.604,2.219 true 4.677,3.083 3.948,2.323 true 4.333,3.188 3.719,2.396 true 2.177,3.125 2.698,2.823 true 2.604,0.5 2.833,0.75 0.229,0.25 10 false *1 1.979,0.802 2.188,1.052 0.208,0.25 10 false *2 1.729,1.219 1.938,1.469 0.208,0.25 10 false *3 2,3.052 2.208,3.333 0.208,0.281 10 false *4 4.333,3.188 4.615,3.427 0.281,0.24 10 false *5 4.688,3.083 4.948,3.302 0.26,0.219 10 false *6 5.26,2.719 5.49,2.958 0.229,0.24 10 false *7 5.917,2.365 6.177,2.563 0.26,0.198 10 false *8 4.49,0.115 4.75,0.344 0.26,0.229 10 false *9 3.365,0.177 3.688,0.427 0.323,0.25 10 false *10
*1 Ring Gear *2 No. 1 Clutch Plate
*3 Ring Gear Coupling *4 Center Differential Case
*5 No. 3 Clutch Plate *6 No. 2 Clutch Plate
*7 Planetary Carrier *8 No. 4 Clutch Plate
*9 Pinion Gear *10 Sun Gear


X132310C01
0.75,1.531 0.521,1.167 true 1.875,1.344 1.677,0.969 true 2.396,1.135 2.25,0.771 true 3.188,0.875 2.969,0.49 true 4.083,0.531 3.896,0.281 true 4.854,0.417 5.125,0.25 true 6.354,2.313 6.042,1.958 true 5.25,2.323 5.563,2.635 true 4.677,2.521 4.99,2.844 true 3.865,2.719 4.271,3.104 true 3.177,3.365 3.615,3.521 true 2.521,3.458 2.854,3.042 true 1.875,3.479 2.135,3.24 true 2.135,0.583 2.365,0.813 0.229,0.229 10 false *1 1.542,0.771 1.813,1 0.271,0.229 10 false *2 0.396,0.979 0.615,1.188 0.219,0.208 10 false *3 1.75,3.469 1.958,3.698 0.208,0.229 10 false *4 2.417,3.458 2.656,3.677 0.24,0.219 10 false *5 3.615,3.427 3.833,3.656 0.219,0.229 10 false *6 4.302,3.083 4.563,3.354 0.26,0.271 10 false *7 5.01,2.823 5.271,3.115 0.26,0.292 10 false *8 5.531,2.635 5.802,2.885 0.271,0.25 10 false *9 6.26,2.313 6.646,2.531 0.385,0.219 10 false *10 5.135,0.115 5.417,0.344 0.281,0.229 10 false *11 3.719,0.094 4.094,0.302 0.375,0.208 10 false *12 2.792,0.281 3.146,0.531 0.354,0.25 10 false *13
*1 No. 1 Clutch Plate *2 Shim
*3 Center Differential Case *4 No. 3 Clutch Plate
*5 Sun Gear *6 Pinion Gear
*7 No. 4 Clutch Plate *8 Planetary Carrier
*9 Carrier Nut *10 Sun Gear Coupling
*11 No. 2 Clutch Plate *12 Ring Gear
*13 Ring Gear Coupling - -


HINT:

The TORSEN LSD cannot be disassembled, so it must be replaced as an assembly. For details, see the Repair Manual.




b.

Normal Driving Operation

i.

During normal driving (front wheel speed = rear wheel speed), the driving force that is input by the center differential case is transmitted (Front: 40/ Rear: 60) as shown below, without involving the LSD function.

X132311C01
2.865,1.802 1.833,0.344 true 3.292,1.667 3.49,0.458 true 4.135,1.74 4.135,0.74 true 4.76,1.646 5.313,0.771 true 3.74,2.99 3.604,2.219 true 1.625,3.99 1.5,3.448 true 1.448,4.448 0.875,3.615 true 2.458,4.302 2.896,3.615 true 2.646,4.323 3.229,3.969 true 2.771,4.698 3.49,4.385 true 5.51,4.104 5.51,3.583 true 3.469,0.271 3.729,0.49 0.26,0.219 10 false *1 1.698,0.167 1.958,0.438 0.26,0.271 10 false *2 0.74,3.438 0.979,3.667 0.24,0.229 10 false *3 3.26,3.854 3.5,4.094 0.24,0.24 10 false *4 3.51,4.281 3.719,4.552 0.208,0.271 10 false *5 2.917,1.01 3.156,1.24 0.24,0.229 10 false *a 4.469,2.604 4.74,2.813 0.271,0.208 10 false *b 5.219,1.823 5.406,2.021 0.188,0.198 10 true *c 2.854,3.427 3.094,3.646 0.24,0.219 10 false *a 5.427,3.385 5.667,3.615 0.24,0.229 10 false *a 1.375,3.26 1.635,3.49 0.26,0.229 10 false *1 5.333,0.646 5.625,0.906 0.292,0.26 10 false *4 4.063,0.542 4.323,0.76 0.26,0.219 10 false *5 3.688,3.01 3.927,3.198 0.24,0.188 10 false *3
*1 Ring Gear *2 Center Differential Case
*3 Sun Gear *4 Planetary Carrier
*5 Pinion Gear - -
*a Input Torque *b Rear Output Torque
*c Front Output Torque - -


Torque Transmission Path
X132312E01
0.125,1.292 0.521,1.771 0.396,0.479 10 false Input 0.948,0.896 1.646,1.875 0.698,0.979 10 false Center Differential Case 2.281,1.083 2.906,1.833 0.625,0.75 10 false Planetary Carrier 3.563,1.063 4.01,1.813 0.448,0.75 10 false Pinion Gear 4.813,0.458 5.198,1.292 0.385,0.833 10 false Sun Gear 4.833,1.719 5.188,2.438 0.354,0.719 10 false Ring Gear 5.76,0.688 6.552,1.438 0.792,0.75 10 false Front Output Torque 5.729,1.854 6.542,2.625 0.813,0.771 10 false Rear Output Torque



c.

Front Wheel Skid Driving Operation

i.

During front wheel skid driving (front wheel speed > rear wheel speed) when a rotational difference exists between the sun gear and the ring gear, the torque distribution of the driving force (torque) that is input by the differential case changes instantly before the torque is transmitted, as follows:

·

The sun gear transmits torque to the planetary carrier while pushing on the No. 4. clutch plate. The planetary carrier transmits this torque to the ring gear from the center differential case via the No. 1. clutch plate.

·

The ring gear outputs torque while pushing on the No. 1. clutch plate.

·

These LSD functions change the torque distribution.


X132313C01
3.115,1.896 1.667,0.385 true 3.094,1.823 3.563,0.573 true 4.479,2.125 5.656,0.74 true 1.698,4.146 1.125,3.635 true 2.052,3.896 2.052,3.385 true 4.865,4.135 4.531,3.677 true 3.375,5.542 2.969,5 true 3.927,2.938 4.177,2.146 true 3.531,0.385 3.771,0.594 0.24,0.208 10 false *1 5.656,0.583 5.906,0.823 0.25,0.24 10 false *2 2.896,0.948 3.125,1.188 0.229,0.24 10 false *a 1.552,0.177 1.792,0.438 0.24,0.26 10 false *b 3.833,2.938 4.063,3.177 0.229,0.24 10 false *c 4.438,2.625 4.677,2.823 0.24,0.198 10 false *d 5.219,1.813 5.417,2 0.198,0.188 10 true *e 4.406,3.5 4.635,3.74 0.229,0.24 10 false *a 0.969,3.469 1.208,3.75 0.24,0.281 10 false *a 1.979,3.167 2.219,3.427 0.24,0.26 10 false *b 3.375,5.552 3.604,5.792 0.229,0.24 10 false *c
*1 No. 1 Clutch Plate *2 No. 4 Clutch Plate
*a Input Torque *b Pushing on the No. 1 Clutch plate
*c Pushing on the No. 4 Clutch plate *d Rear Output Torque
*e Front Output Torque - -


Torque Transmission Path
X132314E01
0.083,1.156 0.479,1.552 0.396,0.396 10 false Input 0.969,0.771 1.656,1.75 0.688,0.979 10 false Center Differential Case 2.573,0.802 3.219,1.646 0.646,0.844 10 false Planetary Carrier 3.563,0.104 4.781,0.5 1.219,0.396 10 false No. 4 Clutch Plate 4.031,0.792 4.458,1.729 0.427,0.938 10 false Pinion Gear 2.281,2.146 3.521,2.563 1.24,0.417 10 false No. 1 Clutch Plate 5.521,0.76 5.865,1.417 0.344,0.656 10 false Sun Gear 5.521,1.844 5.865,2.51 0.344,0.667 10 false Ring Gear 6.448,0.781 6.969,1.802 0.521,1.021 10 false Front Output Torque 6.5,1.823 7,2.729 0.5,0.906 10 false Rear Output Torque



d.

Rear Wheel Skid Driving Operation

i.

During rear wheel skid driving (front wheel speed < rear wheel speed), when a rotational difference exists between the sun gear and the ring gear, the torque distribution of the driving force (torque) that is input by the differential case changes instantly before the torque is transmitted, as follows:

·

The ring gear transmits torque to the center differential case while pushing the No. 1. clutch plate The differential case transmits this torque from the planetary carrier to the sun gear via the No. 4. clutch plate.

·

The sun gear outputs torque while pushing on the No. 4. clutch plate.

·

These LSD functions change the torque distribution.


X132315C01
1.542,0.385 3.115,1.896 true 3.094,1.813 3.708,0.542 true 4.479,2.135 5.615,0.771 true 3.885,2.948 4.167,2.146 true 5.5,4.156 5.229,3.615 true 3.375,5.656 2.917,5.01 true 2.083,3.906 1.948,3.385 true 0.896,3.719 1.688,4.156 true 3.646,0.354 3.896,0.594 0.25,0.24 10 false *1 5.625,0.635 5.875,0.875 0.25,0.24 10 false *2 2.896,1.021 3.083,1.229 0.188,0.208 10 false *a 1.385,0.219 1.594,0.479 0.208,0.26 10 false *b 3.781,2.948 4.01,3.177 0.229,0.229 10 false *c 4.365,2.573 4.646,2.802 0.281,0.229 10 false *d 0.719,3.563 0.99,3.813 0.271,0.25 10 false *a 5.104,3.417 5.385,3.667 0.281,0.25 10 false *a 1.844,3.146 2.083,3.375 0.24,0.229 10 false *b 3.375,5.646 3.646,5.906 0.271,0.26 10 false *c 5.208,1.583 5.417,1.792 0.208,0.208 10 true *e
*1 No. 1 Clutch Plate *2 No. 4 Clutch Plate
*a Input Torque *b Pushing on the No. 1 Clutch plate
*c Pushing on the No. 4 Clutch plate *d Rear Output Torque
*e Front Output Torque - -


Torque Transmission Path
X132316E01
0.083,1.156 0.51,1.521 0.427,0.365 10 false Input 1.042,0.781 1.74,1.74 0.698,0.958 10 false Center Differential Case 2.542,0.792 3.198,1.74 0.656,0.948 10 false Planetary Carrier 3.552,0.083 4.813,0.469 1.26,0.385 10 false No. 4 Clutch Plate 4.021,0.802 4.479,1.698 0.458,0.896 10 false Pinion Gear 5.49,0.781 5.854,1.406 0.365,0.625 10 false Sun Gear 5.521,1.865 5.896,2.479 0.375,0.615 10 false Ring Gear 6.5,0.729 7.052,1.76 0.552,1.031 10 false Front Output Torque 6.5,1.844 7,2.708 0.5,0.865 10 false Rear Output Torque 2.271,2.156 3.583,2.563 1.313,0.406 10 false No. 1 Clutch Plate




TRANSFER SHIFT ACTUATOR


a.

General

i.

The transfer shift actuator assembly consists of the following two mechanisms.

·

H4-L4 switching (to switch the transfer gear ratio)

·

Free-lock switching (to switch the center differential lock)


X132317C01
4.813,1.823 5.125,2.104 0.313,0.281 10 false *a 4.823,2.417 5.083,2.677 0.26,0.26 10 false *b
*a Drive Mechanism (For Free-Lock Switching) *b Drive Mechanism (For H4-L4 Switching)




b.

Drive Mechanism for H4-L4 Switching

i.

The drive mechanism for H4-L4 switching consists a H-L shift motor, limit switch, transfer neutral position switch, wait mechanism (spiral spring), and H-L shift fork shaft. This drive mechanism cannot be disassembled.


ii.

The limit switch has three contact points and detects the shift motor position.


iii.

The wait mechanism (spiral spring) is used for shift fork shaft operations. If the operating resistance of the shift fork shaft is high, the shift rotation is partially stored in the spiral spring. Afterward, when the operating resistance is reduced, the spring force causes the shift fork to slide.

X132318C01
1.729,0.771 2.344,0.771 true 1.375,1.479 2.021,1.479 true 1.031,2.698 1.823,1.854 true 3.781,3.083 3.865,2.625 true 5.625,2.896 5.344,2.094 true 1.208,1.385 1.396,1.625 0.188,0.24 10 false *1 0.906,2.698 1.167,2.979 0.26,0.281 10 false *2 3.708,3.094 4,3.313 0.292,0.219 10 false *3 5.583,2.906 5.844,3.135 0.26,0.229 10 false *4 1.552,0.667 1.76,0.906 0.208,0.24 10 false *a
*1 Transfer Neutral Position Switch *2 H-L Shift Motor
*3 H-L Shift Fork Shaft *4 Limit Switch (HL1, HL2, HL3)
*a Wait Mechanism (Spiral Spring) - -


Combination of 3 Contact Point Switches
X132319E01
0.823,0.938 1.26,1.292 0.438,0.354 10 false HL1 0.823,2.01 1.198,2.365 0.375,0.354 10 false HL2 0.823,3.104 1.26,3.417 0.438,0.313 10 false HL3 1.76,0.656 2.104,0.948 0.344,0.292 10 false OFF 2.573,0.219 2.927,0.427 0.354,0.208 10 false H4 1.802,1.24 2.125,1.583 0.323,0.344 10 false ON 1.802,2.344 2.094,2.625 0.292,0.281 10 false ON 1.76,1.781 2.104,2.073 0.344,0.292 10 false OFF 1.813,3.448 2.104,3.688 0.292,0.24 10 false ON 1.771,2.885 2.115,3.188 0.344,0.302 10 false OFF 4.146,0.188 4.354,0.417 0.208,0.229 10 false N 5.656,0.219 5.948,0.417 0.292,0.198 10 false L4



c.

Drive Mechanism for Free-Lock Switching

i.

The drive mechanism for free-lock switching consists of a center differential lock shift motor, limit switch, center differential lock position switch, wait mechanism (spiral spring), center differential lock shift fork shaft, and actuator temperature sensor*. This drive mechanism cannot be disassembled.


ii.

The limit switch has three contact points and detects the shift motor position.


iii.

The wait mechanism (spiral spring) is used for shift fork shaft operations. If the operating resistance of the shift fork shaft is high, the shift rotation is partially stored in the spiral spring. Afterward, when the operating resistance is reduced, the spring force causes the shift fork to slide.


iv.

An actuator temperature sensor is provided on the shift actuator in order to allow an increase of the amount of current applied to the shift motors, and improves switching performance at low temperatures.*

HINT:

*: Models for Russia


X132320C02
1.292,1.073 1.875,1.073 true 1.25,1.979 2.042,1.979 true 1.521,3.281 2.302,2.938 true 3.635,2.979 2.938,2.125 true 3.99,0.948 4.24,0.469 true 5.313,1.219 5.729,0.531 true 1.073,1.875 1.26,2.156 0.188,0.281 10 false *1 1.094,3.219 1.583,3.531 0.49,0.313 10 false *2 (*A) 3.625,2.979 3.927,3.26 0.302,0.281 10 false *3 5.698,0.344 5.969,0.583 0.271,0.24 10 false *4 4.198,0.281 4.469,0.521 0.271,0.24 10 false *5 1.083,0.958 1.281,1.229 0.198,0.271 10 false *a
*A Models for Russia - -
*1 Center Diff. Lock Position Switch *2 Actuator Temperature Sensor
*3 Center Diff. Lock Shift Motor *4 Limit Switch (TL1, TL2, TL3)
*5 Center Diff. Lock Shift Fork Shaft - -
*a Wait Mechanism (Spiral Spring) - -


Combination of 3 Contact Point Switches
X132321E01
1.021,0.885 1.354,1.219 0.333,0.333 10 false TL1 1.01,2.031 1.396,2.406 0.385,0.375 10 false TL2 0.99,3.167 1.375,3.458 0.385,0.292 10 false TL3 1.75,0.667 2.125,0.969 0.375,0.302 10 false OFF 1.781,1.229 2.115,1.531 0.333,0.302 10 false ON 1.74,1.792 2.094,2.125 0.354,0.333 10 false OFF 1.792,2.344 2.083,2.625 0.292,0.281 10 false ON 1.76,2.896 2.125,3.208 0.365,0.313 10 false OFF 2.479,0.229 2.698,0.427 0.219,0.198 10 false N 1.813,3.458 2.125,3.74 0.313,0.281 10 false ON 4.021,0.198 4.469,0.417 0.448,0.219 10 false Free 5.74,0.198 6.146,0.427 0.406,0.229 10 false Lock