Home › General › BODY ELECTRICAL › METER
NM2660E _V1 General _054361 BODY ELECTRICAL _0272836 METER UN GENERAL/CONTROL/DETAILS F

BODY ELECTRICAL  METER  GENERAL/CONTROL/DETAILS  MULTI-INFORMATION DISPLAY  


MULTI-INFORMATION DISPLAY


a.

General

i.

The multi-information display has 4 areas depending on the display mode.

Display Areas
Y200520E01
3.583,1.25 5.25,1.25 true 3.583,1.979 5.25,2.25 true 3.583,1.802 5.25,1.927 true 3.583,1.594 5.25,1.594 true 5.323,1.156 5.583,1.365 0.26,0.208 10 false A 5.323,1.5 5.583,1.708 0.26,0.208 10 false B 5.323,1.854 5.583,2.063 0.26,0.208 10 false C 5.323,2.156 5.583,2.365 0.26,0.208 10 false D

Displayed Information
Display Areas Mode Outline
A Cruise Information
·

8 types of information (instant fuel consumption, average fuel consumption after refueling, driving range, average fuel consumption, average speed since engine start, distance driven since engine start) can be displayed.

·

The display can be switched by using the DISPswitch.


Dynamic Radar Cruise Control Displays the set vehicle speed and control conditions of the dynamic radar cruise control.
Warning Interrupts the multi-information display immediately when a warning occurs.
Turn by Turn Displays the location of an obstacle and the approximate distance between the vehicle and the obstacle.
Multi-terrain Select Shows the selection display of the multi-terrain select.
Diagnosis Diagnostic Trouble Code (DTC) for the brake control system (TRC and VSC function), tire pressure warning system and VGRS can be displayed.
B Multi-terrain Select Shows the conditions of the multi-terrain select.
Crawl Control Shows the operation conditions of the crawl control.
C Shift Position Displays the current shift position.
Active Height Control Suspension Displays the currently selected vehicle height.
D ODO/TRIP Switches the display of the ODO/TRIP and displays the ODO/TRIP.



b.

Flow of The Multi-information Display Indication

i.

The display mode shown in area A on the multi-information display can be changed as shown in the flow chart below:

Y200521E01
3.354,3 3.667,3.198 0.313,0.198 10 false *1 3.479,0.875 3.792,1.073 0.313,0.198 10 false *2 3.438,0.396 3.75,0.594 0.313,0.198 10 false *1 1.979,1.385 2.198,1.594 0.219,0.208 10 false *3 3.344,3.677 3.656,3.875 0.313,0.198 10 false *1 3.344,4.406 3.656,4.604 0.313,0.198 10 false *1 3.365,5.083 3.677,5.281 0.313,0.198 10 false *1 3.958,3.427 4.271,3.625 0.313,0.198 10 false *2 3.969,4.104 4.281,4.302 0.313,0.198 10 false *2 3.958,4.833 4.271,5.031 0.313,0.198 10 false *2 3.958,5.531 4.271,5.729 0.313,0.198 10 false *2 1.875,4.375 2.104,4.594 0.229,0.219 10 false *1 2.479,4.385 2.792,4.583 0.313,0.198 10 false *2 3.531,6.073 3.844,6.271 0.313,0.198 10 false *1 3.479,6.896 3.792,7.094 0.313,0.198 10 false *1 1.875,0.531 2.979,0.792 1.104,0.26 10 false Display Off 4.479,0.542 5.583,0.802 1.104,0.26 10 false Warning Display 1.781,1.99 2.885,2.25 1.104,0.26 10 false Opening Mode 1.698,3.375 2.802,3.635 1.104,0.26 10 false Advice Display 4.75,3.115 5.854,3.375 1.104,0.26 10 false Warning Display 1.885,7.063 2.698,7.302 0.813,0.24 10 false Display Off 4.427,7.052 5.531,7.313 1.104,0.26 10 false Warning Display 0.823,6.583 1.927,6.844 1.104,0.26 10 false Engine Switch Off 1.438,5.125 3.094,5.448 1.656,0.323 10 false Cruise Information Display 4.5,5.271 6.156,5.594 1.656,0.323 10 false Multi-terrain Select Display 4.635,4.531 6.042,4.833 1.406,0.302 10 false Turn by Turn Display 4.573,3.646 6.052,4.135 1.479,0.49 10 false Dynamic Radar Cruise Control Display 4.885,1.75 6.365,2.052 1.479,0.302 10 false Engine Switch on (IG) 0.823,0.177 2.479,0.5 1.656,0.323 10 false Engine Switch Off 3.5,7.375 3.813,7.573 0.313,0.198 10 false *2 1.958,6.073 2.188,6.25 0.229,0.177 10 false *4

No. Condition
*1 Conditions are met.
*2 Conditions are not met.
*3 Engine switch is turned on (IG).
*4 Engine switch is turned off.



c.

Cruise Information Mode

i.

The cruise information mode is displayed on area A of the multi-information display, and the display switches in the following sequence every time the DISP switch of the steering pad switch is pressed.

Y200522E01
0.375,0.198 0.688,0.396 0.313,0.198 10 false (1) 2.615,0.198 2.927,0.396 0.313,0.198 10 false (2) 4.833,0.198 5.146,0.396 0.313,0.198 10 false (3) 4.844,1.792 5.156,1.99 0.313,0.198 10 false (4) 4.844,3.406 5.156,3.604 0.313,0.198 10 false (5) 4.844,5.031 5.156,5.229 0.313,0.198 10 false (6) 0.385,5.063 0.698,5.26 0.313,0.198 10 false (7) 0.375,3.396 0.688,3.594 0.313,0.198 10 false (8)

Information Outline
(1)
·

Displays average fuel calculated by the combination meter based on information about the driving distance and fuel injection amount.

·

Updates every 0.5 seconds.


·

Displays Eco Drive Indicator Zone calculated by the combination meter based on the accelerator pedal opening angle and the accelerator pedal opening upper threshold level.

·

Flashes the non-eco zone display area in the Eco Drive Indicator Zone when the calculated level is considered as non-eco drive.

·

Updates every 0.2 seconds.


(2)
·

Displays the average fuel consumption after refueling calculated by the combination meter based on the driving distance and fuel consumption amount after refueling.

·

Updates every 10 seconds.


(3)
·

Displays the instantaneous fuel consumption calculated by the combination meter based on the driving distance and fuel injection amount every 20 rotations of the engine.

·

Updates every 0.5 seconds.


(4)
·

Displays the possible driving distance calculated by the combination meter based on the average fuel consumption and the rest of fuel.

·

Updates every 10 seconds.


(5) Displays the vehicle speed.
(6)
·

Displays average speed calculated by the combination meter based on the driving distance and driving time after the reset operation via the ODO/TRIP switch.

·

Updates every 10 seconds.


(7) Displays the front wheel angle.
(8)
·

Displays tire pressures. When the pressure of a tire is low, "LOW TIRE PRESSURE" is illuminated and the low tire pressure value is illuminated.

·

Updates every 1 seconds.





d.

Warning Mode

i.

General

When a warning is necessary, the warning display interrupts the multi-information display.

The master warning light may illuminate or flash and the buzzer may sound depending on the item in the multi-information display.

Display Details Master Warning Light Buzzer

*1: Vehicle speed is 5 km/h (3 mph) or more

*2: Models for Europe with 1VR-FTV engine

*3: Models with diesel engine

*4: Models with diesel engine in compliance with EURO 5 emission regulation

*5: Models for Europe with diesel engine

*6: Models with tire pressure warning system

Y200523

The key is not inside the vehicle. Blinks -
Y200524

The driver door is opened with the shift lever in any position other than P. Blinks -
Y200525

Steering lock has not been released. Blinks Sounds
Y200526

Steering lock is malfunctioning. Illuminates Sounds
Y200527

The power source is switched from OFF to ACC twice with the brake pedal released. Blinks Sounds
Y200528

Key battery is low. Illuminates -
Y200529

Vehicle is traveling with the parking brake engaged. Blinks -
Y200530

Any door is open. Blinks*1 -
Y200531

Y200532

Y200533

Y200534

Y200535

The sliding roof is open and the driver door is open. Blinks -
Y200536

Clearance Sonar System is malfunctioning. Illuminates -
Y200537

Clearance Sonar System is dirty or covered with ice. Illuminates -
Y200538

Pre-crash safety system is malfunctioning. Illuminates Sounds
Y200539

Active height control suspension is malfunctioning. Illuminates Sounds
Y200540

Pre-crash safety system is not currently functional. -
Y200541

Transmission oil temperature exceeds the applicable standards. Illuminates Sounds
Y200542

Engine oil level is low. Illuminates Sounds
Y200543

Fuel system is malfunctioning. Illuminates Sounds
Y200544

Fuel level is low. - -
Y200545

Engine oil is exchange timing.*2 - -
Y200546

Fuel filter clogging is detected. Illuminates Sounds
Y200547

Some moisture has been detected in the fuel filter.*3 Illuminates Sounds
Y200548

A braking or reminder request is made by the pre-crash safety system. - -
Y200549

Crawl control is cancel. Illuminates -
Y200550

Turn assist function is cancel. Illuminates -
Y200551

Dirt is detected on the millimeter wave radar sensor. Illuminates -
Y200552

Dynamic radar cruise control system is not currently functional. Illuminates -
Y200553

Dynamic radar cruise control system is malfunctioning. Illuminates -
Y200554

Transmission control system is malfunction. Illuminates Sounds
Y200555

VGRS system is malfunctioning. Illuminates Sounds
Y200556

The key cannot be identified. Blinks -
Y200557

Control is started when CRAWL control start conditions cannot be met. - -
Y200558

Y200559

Turn assist function is cancel. - -
Y200560

DPF cannot be automatically started.*4 Illuminates -
Y200561

Traction control is off. - -
Y200562

Washer fluid level is low. - -
Y200563

Time for engine oil replacement is close.*2 - -
Y200564

Oil maintenance reset operation has failed.*5 - -
Y200565

Theft deterrent system off. - -
Y200566

Theft deterrent system on. - -
Y200567

Tire pressure warning system is malfunctioning.*6 Illuminates Sounds




FUEL FILTER WARNING (DIESEL ENGINE MODEL)


a.

General

i.

On the analog type combination meter, the fuel filter warning light illuminates when the fuel light is clogged or blinks when condensed water on the fuel filter is detected.


ii.

On the optitron display type combination meter, a warning message corresponding to individual warning items is indicated on the multi-information display.


iii.

This system is controlled by meter ECU.

Function List
Fuel Filter Warning Function Analog Type Combination Meter
Y200568E01
1.5,0.938 3.031,1.135 1.531,0.198 10 false Illuminate

Optitron Type Combination Meter
Y200570E01
1.354,1.24 2.583,1.438 1.229,0.198 10 false :Illuminate 1.188,1.542 2.417,1.74 1.229,0.198 10 false Buzzer: Sound

Fuel Sedimenter Warning Function Analog Type Combination Meter
Y200569E01
1.677,0.99 2.906,1.188 1.229,0.198 10 false Blinking

Optitron Type Combination Meter
Y200571E01
1.333,1.229 3.021,1.427 1.688,0.198 10 false :Illuminate 1.313,1.49 2.781,1.677 1.469,0.188 10 false Buzzer: Sound




b.

Operation

i.

Fuel Filter Warning


ii.

To prevent false alarms on a cold engine, the meter ECU starts its judgment function with the engine switch turned ON, after a total of 30 minutes have elapsed with the input of vehicle speed signal information (minimum vehicle speed of 2.5 km/h).


iii.

The fuel filter warning switch turns OFF when the vacuum in the fuel filter reaches a predetermined level.


iv.

When the meter ECU receives OFF signals from the fuel filter warning switch under the following conditions, it alerts the driver in accordance with the meter specifications.

·

OFF signals from the fuel filter warning switch are input continuously for 10 minutes.

·

When the engine switch is in the ON position, OFF signal (between 1 second and 10 minutes in duration) from the fuel filter warning switch is input twice with a minimum interval of 1 second.



v.

On all models with the optitron display type combination meter, the driver is alerted by the master warning light illuminating, a warning message appearing on the "Fuel Filter Maintenance Reqd" and a buzzer.


vi.

On all models with the analogy type combination meter, the driver is alerted by the fuel filter warning light illuminating.



c.

Fuel Sedimenter Warning

i.

When the amount of water that has accumulated in the sedimenter reaches a predetermined level, the fuel sedimenter level switch, which is located in the bottom of the fuel filter, turns ON. The meter ECU renders this signal as a fuel sedimenter warning and then alerts the driver in accordance with the meter specifications.

·

On models with the optitron display type combination meter, the driver is alerted by the master warning light illuminating, a warning message "High Water Level" appearing on the combination meter and the buzzer sounding.

·

On models with the analogy type combination meter, the driver is alerted by the fuel filter warning light blinking and the buzzer sounding.

HINT:

When the fuel filter warning switch detects a failure, the meter ECU stores this failure in memory, and continues to illuminate* the fuel filter warning light. Therefore, after replacing the fuel filter, the illuminationin formation stored in the meter ECU memory must be erased through the following procedure:

1.

With the engine switch turned OFF, disconnect the fuel filter warning switch connector.

2.

Turn the engine switch from OFF to ON.

3.

After more than 3 seconds but less than 60 seconds have elapsed, reconnect the connector.

4.

After approximately 3 seconds have elapsed with the fuel filter warning switch closed, the system confirms the deletion of the illumination information by turning OFF* the warning light.


*: The warning light will blink in case of a sedimenter failure.


Y200572E01
6.156,3.438 5.979,3.438 5.979,3.438 5.958,2.854 false 2.427,0.448 3.042,0.646 0.615,0.198 10 false Open 2.417,0.865 3.031,1.063 0.615,0.198 10 false Close 2.438,1.198 3.052,1.396 0.615,0.198 10 false OFF 2.479,1.594 2.708,1.729 0.229,0.135 10 false ON 0.302,0.646 2.125,0.854 1.823,0.208 10 false Fuel Filter Warning Switch 0.302,1.385 2.125,1.594 1.823,0.208 10 false Engine Switch 0.302,2.115 2.125,2.323 1.823,0.208 10 false Fuel Filter Warning Light 4,2.594 4.51,2.792 0.51,0.198 10 false 3 sec 3.156,3.063 3.458,3.25 0.302,0.188 10 false (1) 3.844,3.073 4.146,3.26 0.302,0.188 10 false (2) 5.563,3.042 5.865,3.229 0.302,0.188 10 false (3) 6.208,3.042 6.51,3.229 0.302,0.188 10 false (4) 4.177,3.063 5.469,3.25 1.292,0.188 10 false Less than 60 sec. 6.208,3.344 7.156,3.552 0.948,0.208 10 false Approx. 3 sec. 2.438,1.927 3.052,2.125 0.615,0.198 10 false OFF 2.448,2.323 2.823,2.521 0.375,0.198 10 false OFF




d.

Buzzer

i.

The table below shows the warning and reminder functions of the buzzer.

Function Item
Warning
·

Multi-information Display Warning Mode Indication

·

Speed Limit Warning

·

Fuel Filter Warning

·

Fuel Sedimenter Warning


Reminder
·

Key Reminder

·

Seat Belt Reminder

·

Oil Maintenance Reminder