Home › General › NEW FEATURES [2017/08 Update] › NEW FEATURES › from 2017.08
NM2660E _V1 General _066520 NEW FEATURES [2017/08 Update] _0324323 NEW FEATURES UN GENERAL/CONTROL/DETAILS F

NEW FEATURES [2017/08 Update]  NEW FEATURES  GENERAL/CONTROL/DETAILS  AC60F AUTOMATIC TRANSMISSION  


OUTLINE


a.

An AC60F 6-speed Electronic Control Transmission (ECT) is used on the models with 1GR-FE engine.


b.

This automatic transmission is provided with a wide gear ratio, achieving superior output performance and fuel economy. Also, by simplifying the structure, size and weight reduction is achieved.


c.

A gate type shift lever is used.


d.

A multi-mode automatic transmission is used.


e.

A water cooled oil cooler and air cooled oil cooler (oil cooler with hose assembly) are used in the ATF cooling system.



SPECIFICATION


Automatic Transmission Assembly (Models with 1GR-FE Engine)
Gear Ratio 1st 3.600
2nd 2.090
3rd 1.488
4th 1.000
5th 0.687
6th 0.580
Reverse 3.732
Fluid Type Toyota Genuine ATF WS
Fluid Capacity 10.2 Liters (10.8 US qts, 9.0 Imp. qts)
Weight (Reference)* 85.9 kg (189.3 lb)

HINT:

*: Weight refers to a transmission with the fluid fully filled.


Planetary Gears
Engine Type 1GR-FE
Compound Gear Unit Front Planetary Gear Assembly No. of Sun Gear Teeth 46
No. of Pinion Gear Teeth 16
No. of Ring Gear Teeth 78
Center Planetary Gear Assembly No. of Sun Gear Teeth 30
No. of Pinion Gear Teeth 24
No. of Ring Gear Teeth 78
Rear Planetary Gear Assembly No. of Sun Gear Teeth 30
No. of Pinion Gear Teeth 24
No. of Ring Gear Teeth 78

Friction Engagement Components and 1-way Clutch
Engine Type 1GR-FE
No. 1 Clutch (C1) No. of Discs 5
No. 2 Clutch (C2) No. of Discs 5
No. 1 Brake (B1) No. of Discs 5
No. 2 Brake (B2) No. of Discs 7
No. 3 Brake (B3) No. of Discs 4
1-way Clutch (F) No. of Sprags 26

Torque Converter Assembly
Engine Type 1GR-FE
Torque Converter Type 3-element, 1-step, 2-phase
Stall Torque Ratio 1.85


SYSTEM DIAGRAM


X137623E01
0.5,0.219 2.219,0.865 1.719,0.646 10 false Intake Mass Air Flow Meter Sub-assembly 0.688,1.094 2.083,1.625 1.396,0.531 10 false Crank Position Sensor 0.333,1.927 2.51,2.375 2.177,0.448 10 false Throttle Body with Motor Assembly 0.667,2.729 2.021,3.198 1.354,0.469 10 false Throttle Control Motor 0.604,3.479 2.115,3.948 1.51,0.469 10 false Throttle Position Sensor 0.271,4.427 2.521,4.927 2.25,0.5 10 false Accelerator Pedal Sensor Assembly 0.688,5.271 2.115,5.927 1.427,0.656 10 false E.F.I. Engine Coolant Temperature Sensor 0.458,6.125 2.406,6.781 1.948,0.656 10 false No. 1 ATF Temperature Sensor (Transmission Wire) 0.406,6.969 2.354,7.625 1.948,0.656 10 false No. 2 ATF Temperature Sensor (Transmission Wire) 0.188,7.833 2.604,8.281 2.417,0.448 10 false Park/Neutral Position Switch Assembly 3.469,3.99 3.844,4.333 0.375,0.344 10 false ECM 4.896,0.24 6.813,0.875 1.917,0.635 10 false Shift Solenoid Valve SL1 (Shift Control Solenoid Assembly) 4.875,0.979 6.792,1.656 1.917,0.677 10 false Shift Solenoid Valve SL2 (Shift Control Solenoid Assembly) 4.927,1.75 6.833,2.438 1.906,0.688 10 false Shift Solenoid Valve SL3 (Shift Control Solenoid Assembly) 4.906,2.5 6.781,3.188 1.875,0.688 10 false Shift Solenoid Valve SL4 (Shift Control Solenoid Assembly) 4.604,3.26 7.01,3.948 2.406,0.688 10 false Shift Solenoid Valve SLT (Line Pressure Control Solenoid Assembly) 4.76,4.01 6.917,4.667 2.156,0.656 10 false Shift Solenoid Valve SLU (Lock Up Control Solenoid Assembly) 4.677,4.781 7,5.479 2.323,0.698 10 false Shift Solenoid Valve SL (Transmission 3-way Solenoid Assembly) 5.646,6.354 6,6.74 0.354,0.385 10 false ESA 5.146,7.083 6.646,7.552 1.5,0.469 10 false Ignition Coil Assemblies 5.438,7.958 6.24,8.458 0.802,0.5 10 false Spark Plugs 5.083,5.594 6.771,6.094 1.688,0.5 10 false Fuel Injector Assembly

X137624E01
0.26,0.229 2.635,0.688 2.375,0.458 10 false Transmission Floor Shift Assembly 0.208,2.583 2.563,3.052 2.354,0.469 10 false Transmission Revolution Sensor (SP2) 0.469,3.385 2.281,3.833 1.813,0.448 10 false Stop Light Switch Assembly 0.552,4.219 2.25,4.771 1.698,0.552 10 false 4 Wheel Drive Control ECU 0.417,5.104 2.365,6.01 1.948,0.906 10 false Combination Switch Assembly (Integration Control and Panel Assembly) 0.5,6.313 2.198,6.75 1.698,0.438 10 false ECT POWER Mode Switch 0.469,7.094 2.24,7.542 1.771,0.448 10 false ECT 2nd Start Mode Switch 3.427,3.365 3.813,3.75 0.385,0.385 10 false ECM 4.948,0.271 6.802,0.708 1.854,0.438 10 false Combination Meter Assembly 5.24,1.021 6.594,1.448 1.354,0.427 10 false Vehicle Speed Signal 5.76,1.667 6.115,2.073 0.354,0.406 10 false MIL 5.292,2.302 6.594,2.865 1.302,0.563 10 false ECT POWER Mode Indicator Light 5.313,3.042 6.583,3.594 1.271,0.552 10 false ECT 2nd Start Mode Indicator Light 5.125,3.771 6.74,4.177 1.615,0.406 10 false Shift Range Indicator Light 5.229,4.313 6.677,4.708 1.448,0.396 10 false S Mode Indicator Light 5.417,4.865 6.552,5.375 1.135,0.51 10 false ATF Temperature Warning Light 5.667,5.604 6.156,5.979 0.49,0.375 10 false Buzzer 5.823,8.021 6.198,8.521 0.375,0.5 10 false DLC3 0.406,0.854 2.385,1.302 1.979,0.448 10 false Transmission Control Switch 0.229,1.781 2.583,2.219 2.354,0.438 10 false Transmission Revolution Sensor (NT) 4.146,3.302 4.75,3.896 0.604,0.594 10 false CAN (V1 Bus) 5.021,6.51 6.698,7.01 1.677,0.5 10 false Network Gateway ECU*1 4.656,7.135 5.021,7.417 0.365,0.281 10 false *2 6.292,7.25 7,7.927 0.708,0.677 10 false CAN (Diag Bus) 5.521,7.135 5.885,7.417 0.365,0.281 10 false *1 0.219,8.427 2.948,8.854 2.729,0.427 10 false *2: Models without Network Gateway ECU 0.229,8 2.75,8.406 2.521,0.406 10 false *1: Models with Network Gateway ECU


PARTS LOCATION


X137625C01
2.521,1.792 2.177,0.625 2.177,0.625 2.063,0.625 true 1.979,2.031 1.49,1.073 1.49,1.073 1.375,1.073 true 2.271,2.333 0.896,3.875 0.896,3.875 0.781,3.875 true 2.51,3.031 1.833,4.333 1.833,4.333 1.698,4.333 true 3.156,2.375 5.625,1.344 5.625,1.344 5.75,1.344 true 3.01,2.344 5.094,0.552 5.094,0.552 5.219,0.552 true 2.906,2.396 4.104,0.427 4.104,0.427 4.229,0.427 true 1.292,8.042 0.75,7.094 0.75,7.094 0.635,7.094 true 1.875,7.969 1.375,6.906 1.375,6.906 1.25,6.906 true 2.031,8.125 2.5,8.625 2.5,8.625 2.625,8.625 true 5.156,7.771 5.417,8.448 5.417,8.448 5.542,8.448 true 5.719,6.635 6.198,7.573 6.198,7.573 6.323,7.573 true 1.885,0.51 2.073,0.688 0.188,0.177 10 false *1 1.177,0.969 1.344,1.167 0.167,0.198 10 false *2 0.615,3.76 0.927,3.917 0.313,0.156 10 false *3 1.542,4.24 1.854,4.396 0.313,0.156 10 false *4 5.771,1.25 6.083,1.406 0.313,0.156 10 false *5 5.24,0.448 5.552,0.604 0.313,0.156 10 false *6 4.25,0.333 4.563,0.49 0.313,0.156 10 false *7 0.458,6.979 0.771,7.135 0.313,0.156 10 false *8 1.063,6.792 1.375,6.948 0.313,0.156 10 false *9 2.667,8.531 3.135,8.688 0.469,0.156 10 false *10 5.594,8.354 6.063,8.51 0.469,0.156 10 false *11 6.354,7.469 6.823,7.625 0.469,0.156 10 false *12
*1 ECM *2 Intake Mass Air Flow Meter Sub-assembly
*3 Throttle Body with Motor Assembly
·

Throttle Control Motor

·

Throttle Position Sensor


*4 Crank Position Sensor
*5 Ignition Coil Assemblies *6 E.F.I. Engine Coolant Temperature Sensor
*7 Fuel Injector Assemblies *8 No. 1 ATF Temperature Sensor (Transmission Wire)
*9 Park/Neutral Position Switch Assembly *10 No. 2 ATF Temperature Sensor (Transmission Wire)
*11 Water Cooled Oil Cooler (Built-In Radiator) *12 Air Cooled Oil Cooler (Oil Cooler with Hose Assembly)


X137626C01
3.969,1.802 4.229,0.552 4.229,0.552 4.354,0.552 true 3.365,2.5 2.833,0.698 2.833,0.698 2.677,0.698 true 3.219,3.292 2.104,4.271 2.104,4.271 1.948,4.271 true 3.427,3.323 2.698,4.406 2.698,4.406 2.542,4.406 true 3.594,3.302 3.229,4.5 3.229,4.5 3.073,4.5 true 3.74,3.281 4.063,4.49 4.063,4.49 4.188,4.49 true 3.958,3.167 4.688,4.417 4.688,4.417 4.813,4.417 true 4.125,3.146 5.281,4.24 5.281,4.24 5.406,4.24 true 4.188,3.042 5.771,3.906 5.771,3.906 5.896,3.906 true 4.396,0.448 4.708,0.604 0.313,0.156 10 false *1 2.5,0.594 2.677,0.771 0.177,0.177 10 false *2 1.771,4.156 1.938,4.313 0.167,0.156 10 false *3 2.365,4.281 2.552,4.469 0.188,0.188 10 false *4 2.917,4.385 3.125,4.552 0.208,0.167 10 false *5 4.208,4.385 4.521,4.542 0.313,0.156 10 false *6 4.844,4.281 5.156,4.438 0.313,0.156 10 false *7 5.448,4.125 5.76,4.281 0.313,0.156 10 false *8 5.927,3.781 6.24,3.938 0.313,0.156 10 false *9
*1 Transmission Revolution Sensor (SP2) *2 Transmission Revolution Sensor (NT)
*3 Shift Solenoid Valve SLT (Line Pressure Control Solenoid Assembly) *4 Shift Solenoid Valve SL2 (Shift Control Solenoid Assembly)
*5 Shift Solenoid Valve SL1 (Shift Control Solenoid Assembly) *6 Shift Solenoid Valve SL3 (Shift Control Solenoid Assembly)
*7 Shift Solenoid Valve SLU (Lock Up Control Solenoid Assembly) *8 Shift Solenoid Valve SL4 (Shift Control Solenoid Assembly)
*9 Shift Solenoid Valve SL (Transmission 3-way Solenoid Assembly) - -


X137627C01
3.823,2.385 3.594,2.969 3.594,2.969 3.438,2.969 true 5.688,2.375 5.938,2.99 5.938,2.99 6.063,2.99 true 3.573,1.604 3.813,0.75 3.813,0.75 3.938,0.75 true 1.531,6.365 1.052,8.583 1.052,8.583 0.896,8.583 true 2.156,6.979 1.938,8.375 1.938,8.375 1.781,8.375 true 2.24,6.594 2.708,7.906 2.708,7.906 2.833,7.906 true 4.177,7.229 3.875,8.385 3.875,8.385 3.719,8.385 true 4.635,6.917 6.406,7.969 6.406,7.969 6.531,7.969 true 5.448,4.958 6.375,5.948 6.375,5.948 6.5,5.948 true 5.604,2.25 6.031,1.885 6.031,1.885 6.156,1.885 true 5.583,2.104 5.979,1.094 5.979,1.094 6.104,1.094 true 1.781,2.396 1.438,2.938 1.438,2.938 1.281,2.938 true 5.385,4.427 5.146,3.615 5.146,3.615 5.01,3.615 true 0.802,0.625 1.115,0.781 0.313,0.156 10 false *1 1.125,2.833 1.302,2.99 0.177,0.156 10 false *a 3.281,2.896 3.448,3.083 0.167,0.188 10 false *b 6.073,2.896 6.385,3.052 0.313,0.156 10 false *c 6.135,1 6.448,1.156 0.313,0.156 10 false *e 3.979,0.667 4.292,0.823 0.313,0.156 10 false *f 0.719,8.49 1.031,8.646 0.313,0.156 10 false *2 1.625,8.281 1.938,8.438 0.313,0.156 10 false *3 2.875,7.813 3.344,7.969 0.469,0.156 10 false *4 3.542,8.292 4.01,8.448 0.469,0.156 10 false *5 6.563,7.865 7.031,8.021 0.469,0.156 10 false *6 6.521,5.854 6.99,6.01 0.469,0.156 10 false *7 6.177,1.802 6.49,1.958 0.313,0.156 10 false *d 4.542,3.49 5.063,3.708 0.521,0.219 10 false *8 (*A)
*A Models with Network Gateway ECU - -
*1 Combination Meter Assembly *2 Stop Light Switch Assembly
*3 Accelerator Pedal Sensor Assembly *4 DLC3
*5 Transmission Floor Shift Assembly
·

Transmission Control Switch


*6 Combination Switch Assembly (Integration Control and Panel Assembly)
·

ECT POWER Mode Switch

·

ECT 2nd Start Mode Switch


*7 4 Wheel Drive Control ECU *8 Network Gateway ECU
*a MIL *b Shift Range Indicator
*c ATF Temperature Warning Light *d ECT 2nd Start Mode Indicator Light
*e ECT POWER Mode Indicator Light *f Shift Position Indicator Light (P, R, N, D, S)



FUNCTION OF MAIN COMPONENTS


Component Function
Torque Converter Assembly
·

Transmits the engine power to the transmission.

·

Increases engine torque.


Oil Pump Assembly Provides oil pressure necessary for transmission operation.
No. 1 Clutch (C1) Connects the input shaft and the intermediate shaft.
No. 2 Clutch (C2) Connects the input shaft and the center planetary gear assembly.
No. 1 Brake (B1) Locks the rotations of the front planetary carrier and the center planetary ring gear.
No. 2 Brake (B2) Locks the rotation of the rear planetary ring gear.
No. 3 Brake (B3) Locks the rotation of the front planetary ring gear.
1-way Clutch (F) Locks the counterclockwise rotations of the center planetary carrier and the rear planetary ring gear.
Planetary Gears Change the power transmission route in accordance with clutch and brake operation, and increase or decrease output shaft revolution accordingly.
Shift Solenoid Valve SL1 (Shift Control Solenoid Assembly) Performs shift controls.
Shift Solenoid Valve SL2 (Shift Control Solenoid Assembly) Performs shift controls.
Shift Solenoid Valve SL3 (Shift Control Solenoid Assembly) Performs shift controls.
Shift Solenoid Valve SL4 (Shift Control Solenoid Assembly) Performs shift controls.
Shift Solenoid Valve SLT (Line Pressure Control Solenoid Assembly) Controls line pressure.
Shift Solenoid Valve SLU (Lock Up Control Solenoid Assembly)
·

Performs lock-up clutch controls.

·

Performs B2 brake hydraulic pressure controls (only for the 1st range when the S position is selected).


Shift Solenoid Valve SL (Transmission 3-way Solenoid Assembly) Shifts between lock-up hydraulic pressure and B2 brake hydraulic pressure.
No. 1 ATF Temperature Sensor (Transmission Wire) Detects the ATF temperature.
No. 2 ATF Temperature Sensor (Transmission Wire) Detects the ATF temperature.
Transmission Revolution Sensor (NT) Detects the input speed of the transmission.
Transmission Revolution Sensor (SP2) Detects the output speed of the transmission.
Park/Neutral Position Switch Assembly Detects the shift lever position (P, R, N, D).
Transmission Floor Shift Assembly Transmission Control Switch
·

Detects that the shift lever is in S.

·

Detects the driver's upshift and downshift operations when the shift lever is in S.


Combination Switch Assembly (Integration Control and Panel Assembly) ECT POWER Mode Switch Switches the ECT POWER mode.
ECT 2nd Start Mode Switch Switches the ECT 2nd start mode.
Stop Light Switch Assembly Detects when the brake pedal is depressed.
Combination Meter Assembly Transmits the vehicle speed signal to the ECM.
Combination Meter Assembly Shift Position Indicator Light Indicates the shift position.
Shift Range Indicator When S position is selected, indicates current shift range.
MIL Illuminates to inform the driver when the ECM detects a malfunction.
ECT POWER Mode Indicator Light Illuminates when the driver selects the ECT POWER mode.
ECT 2nd start Mode Indicator Light Illuminates when the driver selects the ECT 2nd start mode.
ATF Temperature Warning Light Warns the driver by lighting up when the ATF is at a high temperature.
Buzzer Sounds when shift-down operation is rejected in S position.
ECM
·

Controls each solenoid valve and engine output in response to signals from each sensor and switch.

·

When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section.


4 Wheel Drive Control ECU Sends a transfer position signal to inform the ECM.


SYSTEM CONTROL


Electronic Control of Automatic Transmission
Control Function
Powertrain Cooperative Control Controls both the shift control and engine output control in an integrated way, thus achieving excellent shift characteristics and driveability.
Shift Timing Control The ECM sends current to shift solenoid valves (SL1), (SL2), (SL3), (SL4) and/or (SL) based on signals from various sensors in order to shift the gears.
Line Pressure Control Actuates the shift solenoid valve (SLT) to control the line pressure in accordance with information from the ECM and the operating conditions of the transmission.
Clutch Pressure Optimal Control The shift solenoid valves (SL1), (SL2), (SL3), (SL4), (SLT) and (SLU) minutely control the clutch pressure in accordance with the engine output and driving conditions of the transmission.
Clutch to Clutch Pressure Control By utilizing pressure output from shift solenoid valves (SL1), (SL2), (SL3) and (SL4) based on drive signals sent from the ECM, each of the clutch and brake hydraulic pressures can be controlled directly and independently.
Vehicle Lift Control The clutch release speed has been optimized to restrain the upward movement of the vehicle when the shift lever is moved from D to N.
Shift Down Control The hydraulic passages and control have been optimized in order to ensure a smooth shift feel during downshifting to accelerate the vehicle.
Engine Torque Control Retards the engine ignition timing temporarily to improve shift feeling while upshifts or downshifts occur.
Lock-up Timing Control The ECM sends current to the shift solenoid valve (SLU) based on signals from various sensors and engages or disengages the lock-up clutch.
Flex Lock-up Clutch Control Controls theshift solenoid valve (SLU), provides an intermediate mode for when the lockup clutch is between on and off, and increases the operating range of the lock-up clutch to improve fuel economy.
Coast Downshift Control The ECM performs downshifts before fuel cut ends to prevent the engine speed from decreasing and maintain the fuel cut.
Artificial Intelligence-shift Control (AI-shift Control) Based on the signals from various sensors, the ECM determines the road conditions and the intention of the driver. Thus, an appropriate shift pattern is automatically determined, which improves driveability.
Multi-mode Automatic Transmission The ECM appropriately controls the automatic transmission in accordance with the shift range position selected while the shift lever is in S.
ATF High Temperature Control When the ATF is at a high temperature, normal shifting characteristics will be changed to shifting characteristics which actively utilize the low gear range to prevent the oil temperature from rising further.

a.

Powertrain Cooperative Control

i.

The Driving Response and Acceleration Management System (DRAMS) is used for this model. This system integrally controls the engine, transmission and other driving related controls in order to improve vehicle maneuverability and driving comfort, as well as provide optimal drive feeling as a whole, including the behavior of the vehicle, while taking into account the driver's needs and environment.


ii.

By integrally controlling the engine and automatic transmission using this system, acceleration maneuvers are replaced with drive force demanded by the driver. As a result, quick response and a high quality driving experience in accordance with the driver's intentions is achieved, such as when accelerating or decelerating, starting or stopping, or during gear shifts to provide demanded drive force while still producing a smoother shift transition.

X127069E04
1.104,1.313 1.75,1.698 0.646,0.385 10 false Engine 2.906,1.698 3.792,2.698 0.885,1 10 false Automatic Transmission 5.24,0.76 5.625,1.583 0.385,0.823 10 false Drive Force 6.344,1.51 6.833,1.917 0.49,0.406 10 false Time 5.396,2.333 6.948,2.75 1.552,0.417 10 false Generated Drive Force 3.24,3.156 4.49,3.521 1.25,0.365 10 false Engine Control 4.802,3.156 6.24,3.531 1.438,0.375 10 false Transmission Control 1.365,3.823 1.74,4.583 0.375,0.76 10 false Drive Force 2.198,4.438 2.615,4.865 0.417,0.427 10 false Time 1.115,4.896 2.396,5.667 1.281,0.771 10 false Converted into Drive Force Value 2.927,3.958 4.521,4.708 1.594,0.75 10 false Determination of Necessary Engine Torque 4.885,3.958 6,4.708 1.115,0.75 10 false Determination of Appropriate Gear 3.281,5.156 5.896,5.427 2.615,0.271 10 false Determination of Necessary Drive Force 4.49,5.583 6.073,5.948 1.583,0.365 10 false Powertrain Management 0.24,6.104 1.354,6.917 1.115,0.813 10 false Accelerator Pedal Operation 3.438,5.906 3.938,6.313 0.5,0.406 10 false ECM 5.073,6.146 6.656,6.51 1.583,0.365 10 false Skid Control ECU 4.948,6.5 6.531,6.865 1.583,0.365 10 false Brake Control System 0.625,6.917 2.208,7.281 1.583,0.365 10 false : Drive force 0.625,7.344 2.417,7.667 1.792,0.323 10 false : Drive force control signal 2.875,7.344 4.833,7.646 1.958,0.302 10 false : Cooperative control signal


iii.

Start Control

·

With DRAMS, engine torque will optimally be controlled in a real-time manner in accordance with speed ratios between engine speed and turbine speed so that finely controlled starting capability has been provided while balancing the "reduction of a feel of jump and suppression of tire slipping" and "smooth responsiveness" when starting.




b.

Line Pressure Control

i.

In order to obtain predetermined line pressure characteristics in accordance with each sensor signal, the ECM activates the shift solenoid valve (SLT) to regulate the throttle pressure.


ii.

This makes it possible for the primary regulator valve to precisely and minutely control the line pressure in accordance with the engine output, thus providing smoother shift characteristics.

X137628E01
0.5,0.542 1.427,0.854 0.927,0.313 10 false Line Pressure 0.75,2.333 1.167,3.25 0.417,0.917 10 false Oil Pump 1.302,1.49 1.958,2.469 0.656,0.979 10 false Primary Regulator Valve 3.219,2.083 4.135,2.802 0.917,0.719 10 false Shift Solenoid Valve (SLT) 4.615,2.385 4.99,2.75 0.375,0.365 10 false ECM 1.885,3.677 2.51,4.406 0.625,0.729 10 false Fluid Pressure 3.344,4.844 3.865,5.198 0.521,0.354 10 false Current 5.542,0.573 6.781,0.948 1.24,0.375 10 false Input Speed Signal 5.531,1.104 6.656,1.51 1.125,0.406 10 false ATF Temperature 5.521,1.667 6.375,2.063 0.854,0.396 10 false Shift Position 5.542,2.208 6.406,2.563 0.865,0.354 10 false Gear Position 5.542,2.719 6.688,3.406 1.146,0.688 10 false Accelerator Pedal Opening Angle 5.51,3.531 6.49,4.25 0.979,0.719 10 false Engine Coolant Temperature 5.531,4.927 6.677,5.271 1.146,0.344 10 false Throttle Position 5.552,4.354 6.469,4.708 0.917,0.354 10 false Engine Speed



c.

Clutch Pressure Optimal Control

i.

The ECM monitors the signals from various types of sensors, such as the transmission revolution sensor (NT), allowing shift solenoid valves (SL1), (SL2), (SL3), (SL4), (SLT) and (SLU) to minutely control the clutch pressure in accordance with engine output and driving conditions. As a result, smooth shift characteristics are achieved.

X127071E06
3.104,3.083 2.667,2.365 2.667,2.365 2.479,2.365 true 4.083,3.104 4.385,2.313 4.385,2.313 4.635,2.313 true 3.542,3.917 3.073,4.781 3.073,4.781 2.885,4.781 true 3.75,3.865 3.219,5.427 3.219,5.427 3.031,5.427 true 3.906,3.854 3.406,6.104 3.406,6.104 3.219,6.104 true 0.26,0.385 0.615,1.646 0.354,1.26 10 false Input Shaft rpm 1.438,0.25 2.323,1.094 0.885,0.844 10 false Target rpm Change Ratio 0.74,1.302 2.51,1.667 1.771,0.365 10 false Practical rpm Change Ratio 1.688,1.698 2.198,2.021 0.51,0.323 10 false Time 5.573,1.229 6.021,1.656 0.448,0.427 10 false ECM 0.146,2.26 2.406,2.625 2.26,0.365 10 false Transmission Revolution Sensor (NT) 4.677,2.219 7.115,2.594 2.438,0.375 10 false Transmission Revolution Sensor (SP2) 5.146,2.865 5.594,4.167 0.448,1.302 10 false Output Shaft Torque 6.604,3.823 7,4.219 0.396,0.396 10 false Time 0.938,4.656 2.917,5.26 1.979,0.604 10 false Shift Solenoid Valve (SL1, SL2, SL3, SL4, SLT, SLU) 1.083,5.323 3.031,5.906 1.948,0.583 10 false No. 1 ATF Temperature Sensor (Transmission Wire) 1.281,5.99 3.208,6.469 1.927,0.479 10 false No. 2 ATF Temperature Sensor (Transmission Wire) 4.802,4.698 5.604,5.583 0.802,0.885 10 false Clutch/Brake Pressure 5.625,5.677 7.01,6.073 1.385,0.396 10 false Solenoid Drive Signal



d.

Clutch to Clutch Pressure Control

i.

By using a clutch to clutch pressure control without using 1-way clutches in the 2nd or higher gears, a light, compact 6-speed automatic transmission has been provided.


ii.

By utilizing pressure output from shift solenoid valves (SL1), (SL2), (SL3) and (SL4) based on drive signals sent from the ECM, each of the clutch and brake hydraulic pressures can be controlled directly and independently.

X127072E16
0.458,0.885 1.698,1.302 1.24,0.417 10 false Clutch Control Valve 0.458,2.219 1.698,2.635 1.24,0.417 10 false Clutch Control Valve 0.448,3.542 1.708,3.938 1.26,0.396 10 false Brake Control Valve 0.458,4.865 1.698,5.271 1.24,0.406 10 false Brake Control Valve 0.115,5.323 1.167,5.542 1.052,0.219 10 false Line Pressure 2.979,0.594 3.75,1.333 0.771,0.74 10 false Shift Solenoid Valve (SL1) 2.969,1.927 3.75,3.177 0.781,1.25 10 false Shift Solenoid Valve (SL2) 2.958,3.229 3.74,4.448 0.781,1.219 10 false Shift Solenoid Valve (SL3) 2.948,4.542 3.75,5.594 0.802,1.052 10 false Shift Solenoid Valve (SL4) 3.823,2.49 4.563,3.01 0.74,0.521 10 false ECM 4.656,0.438 7.104,0.708 2.448,0.271 10 false Transmission Revolution Sensor (NT) 4.656,1 7.104,1.271 2.448,0.271 10 false Transmission Revolution Sensor (SP2) 4.656,1.563 7.094,2 2.438,0.438 10 false No. 1 ATF Temperature Sensor (Transmission Wire) 4.656,2.146 7.073,2.583 2.417,0.438 10 false No. 2 ATF Temperature Sensor (Transmission Wire) 4.667,2.719 6.51,3.188 1.844,0.469 10 false Intake Mass Air Flow Meter Sub-assembly 4.646,3.448 6.896,3.979 2.25,0.531 10 false E.F.I. Engine Coolant Temperature Sensor 4.667,4.042 6.979,4.354 2.313,0.313 10 false Accelerator Pedal Sensor Assembly 4.656,4.594 6.969,4.906 2.313,0.313 10 false Throttle Position Sensor



e.

Lock-up Timing Control

i.

The ECM operates the lock-up timing control in order to improve fuel economy.

Lock-up Timing Control Operation
Gear Position Shift Lever Position or Shift Range
D, S6 S5 S4
1st X X X
2nd X X X
3rd X X X
4th â—‹ â—‹ â—‹
5th â—‹ â—‹ -
6th â—‹ - -

HINT:

â—‹: Available

X: Does not operate

-: Not applicable




f.

Flex Lock-up Clutch Control

i.

During acceleration, partial control of the power transmission between the lock-up clutch and torque converter greatly boosts transmission efficiency in accordance with the driving conditions, improving fuel economy.


ii.

Even when the vehicle is decelerating (the accelerator pedal is released), flex lock-up clutch control operates. As a result, the fuel cut area is expanded and fuel economy is improved.


iii.

By allowing flex lock-up clutch control to continue operating during gearshifts, smooth torque transmission is obtained. As a result, fuel economy and driveability are improved.


iv.

For flex lock-up clutch control, H infinity (H∞) control theory is used to achieve a high level of system stability and response to various characteristic changes.

X138059E01
2.156,1.615 1.729,1.031 1.729,1.031 1.604,1.031 true 6.167,1.521 6.042,1.146 6.042,1.146 5.917,1.146 false 6.094,1.688 6.208,1.865 6.208,1.865 6.313,1.865 false 3.75,4.604 2.688,2.5 2.688,2.5 2.563,2.5 true 2.51,4.021 1.979,3.177 1.979,3.177 1.854,3.177 true 1.823,4.427 1.198,3.938 1.198,3.938 1.073,3.938 true 1.854,4.896 1.344,5.563 1.344,5.563 1.219,5.563 true 3.875,5.448 3.323,5.74 3.323,5.74 3.198,5.74 true 4.167,5.438 3.302,6.125 3.302,6.125 3.177,6.125 true 4.49,5.385 4.615,6.021 4.615,6.021 4.719,6.021 true 4.396,5.365 3.823,6.552 3.823,6.552 3.677,6.552 true 3.396,0.427 3.771,0.75 0.375,0.323 10 false ECM 0.448,0.938 1.583,1.594 1.135,0.656 10 false Accelerator Pedal Sensor Assembly 4.604,1.042 5.927,1.396 1.323,0.354 10 false Engine Speed Signal 6.354,1.604 6.781,2.688 0.427,1.083 10 false Input Speed Signal 5.25,2.146 6.188,2.469 0.938,0.323 10 false Vehicle Speed 4.625,1.448 5.073,2.156 0.448,0.708 10 false Engine Speed 6.208,3.083 6.781,4.094 0.573,1.01 10 false Linear Solenoid Signal 4.625,3.281 5.125,3.594 0.5,0.313 10 false Current 5.469,3.729 5.802,4.052 0.333,0.323 10 false Time 4.792,5.906 6.688,6.281 1.896,0.375 10 false No. 2 ATF Temperature Sensor (Transmission Wire) 0.49,6.438 3.781,6.823 3.292,0.385 10 false No .1 ATF Temperature Sensor (Transmission Wire) 1.51,6.01 3.26,6.385 1.75,0.375 10 false Shift Solenoid Valve (SLU) 1.781,5.615 3.146,6.021 1.365,0.406 10 false Lock-up Control Valve 0.25,5.448 1.188,6.104 0.938,0.656 10 false Crank Position Sensor 0.167,3.813 1.031,4.906 0.865,1.094 10 false E.F.I. Engine Coolant Temperature Sensor 0.281,3.073 1.792,3.427 1.51,0.354 10 false Throttle Position Sensor 0.229,2.396 2.49,2.781 2.26,0.385 10 false Transmission Revolution Sensor (NT)

X102147E32
2.615,1.083 5.635,1.427 3.021,0.344 10 false : Lock-up operating range 0.271,0.125 3.292,0.469 3.021,0.344 10 false Flex Lock-up Operating Range 2.615,1.448 5.635,1.792 3.021,0.344 10 false : Flex lock-up operating range (acceleration) 2.615,1.813 5.635,2.156 3.021,0.344 10 false : Flex lock-up operating range (deceleration) 3.24,4.229 4.167,4.573 0.927,0.344 10 false Vehicle Speed 1.604,2.135 2,2.479 0.396,0.344 10 false Large 4.917,4.198 5.24,4.542 0.323,0.344 10 false High 0.813,3.01 1.99,3.688 1.177,0.677 10 false Accelerator Pedal Depressing Angle 0.583,4.083 1.729,4.75 1.146,0.667 10 false Accelerator Pedal is Released

Flex Lock-up Clutch Control Operation (Acceleration)
Gear Position Shift Lever Position or Shift Range
D, S6 S5 S4
1st X X X
2nd X X X
3rd X X X
4th â—‹ â—‹ â—‹
5th â—‹ â—‹ -
6th â—‹ - -

HINT:

â—‹: Operates

X: Does not operate

-: Not applicable


Flex Lock-up Clutch Control Operation (Deceleration)
Gear Position Shift Lever Position or Shift Range
D, S6 S5 S4
1st X X X
2nd X X X
3rd X X X
4th â—‹ â—‹ X
5th â—‹ â—‹ -
6th â—‹ - -

HINT:

â—‹: Operates

X: Does not operate

-: Not applicable




g.

Coast Downshift Control

i.

Downshift control is used when decelerating, allowing for low fuel consumption by extending fuel cut control as much as possible.


ii.

By performing flex lock-up control and downshift control at the same time when decelerating, a decrease of engine speed has been suppressed, while extending fuel cut control as much as possible without lowering the engine speed below the fuel cut recovery speed.


iii.

By expanding operating gears and widening operating areas through close-gear ratios, fuel efficiency has significantly been enhanced and drivability has been improved by optimizing deceleration force when controls are activated.

X127076E03
1.958,1.49 2.073,1.49 2.073,1.49 2.208,1.771 false 2.917,1.552 3.031,1.552 3.031,1.552 3.167,1.833 false 4.167,1.677 4.042,1.677 4.042,1.677 3.917,1.969 false 4.719,2.698 4.594,2.698 4.594,2.698 4.469,2.448 false 3.979,2.688 4.094,2.688 4.094,2.688 4.167,2.396 false 3.469,2.563 3.583,2.563 3.583,2.563 3.792,2.354 false 0.448,0.594 1.375,1.031 0.927,0.438 10 false Engine Speed 0.438,2 1.302,2.688 0.865,0.688 10 false Fuel Cut Return Speed 0.448,2.917 1.104,3.802 0.656,0.885 10 false Fuel Cut Duration 2.25,0.729 3.719,1.438 1.469,0.708 10 false Coast Downshifts Occur Earlier 1.542,1.375 2.021,1.688 0.479,0.313 10 false To 6th 2.469,1.448 2.938,1.823 0.469,0.375 10 false To 5th 4.229,1.583 4.813,1.906 0.583,0.323 10 false To 4th 4.99,2.99 5.5,3.323 0.51,0.333 10 false Time 3.146,3.427 4.24,3.802 1.094,0.375 10 false Extended Time 4.854,3.385 6.615,4.458 1.76,1.073 10 false Enhanced Fuel Efficiency Through Extended Fuel Cut Control 4.844,0.167 6.938,0.51 2.094,0.344 10 false : With coast downshift control 4.844,0.573 6.958,0.948 2.115,0.375 10 false : Without coast downshift control 4.76,2.594 5.344,2.927 0.583,0.333 10 false To 4th 3.563,2.573 4.031,2.948 0.469,0.375 10 false To 5th 3.042,2.458 3.51,2.854 0.469,0.396 10 false To 6th



h.

Artificial Intelligence-shift Control (AI-shift Control)

i.

AI-shift control selects optimal controls in accordance with "driving environment" and the "driver's intention" based on the degree of accelerator opening, vehicle speed, brake signals, etc.


ii.

Smooth driving and low fuel consumption have been achieved while driving normally. A strong and linear feeling of acceleration has been provided when accelerating. A direct feeling of deceleration through engine braking and high fuel efficiency have been achieved when decelerating.

X127077E04
2.26,0.083 5.01,0.802 2.75,0.719 10 false Selects Optimal Controls in accordance with "Driving Environment" and "Driver's Intention" 2.802,0.885 4.51,1.292 1.708,0.406 10 false Control when Accelerating 2.896,2.052 4.479,2.417 1.583,0.365 10 false Automatic Shift Control 2.917,3.271 4.521,3.688 1.604,0.417 10 false Uphill/Downhill Control 2.375,1.406 4.896,1.719 2.521,0.313 10 true Direct and Linear Feeling of Acceleration 2.396,2.552 4.948,2.906 2.552,0.354 10 true Smooth Drive and Low Fuel Consumption 2.469,4.219 5.271,4.625 2.802,0.406 10 false - Securing Engine Braking Going Downhill 2.469,3.885 5.031,4.229 2.563,0.344 10 false - Maintaining Drive Force Going Uphill


iii.

Under road condition support control, the ECM identifies the throttle valve opening angle, accelerator pedal opening angle and vehicle speed to determine whether the vehicle is being driven uphill or downhill. Unnecessary upshifting is restrained to automatically achieve optimal drive force at all times while driving uphill. Downshifting is automatically conducted to achieve optimal engine brake force while driving downhill.

X127078E03
0.635,2.823 1.031,3.146 0.396,0.323 10 false 6th 0.635,3.323 0.948,3.604 0.313,0.281 10 false 6th 1.26,2.823 1.542,3.146 0.281,0.323 10 false 4th 1.677,2.823 2.01,3.115 0.333,0.292 10 false 5th 2,2.823 2.344,3.167 0.344,0.344 10 false 3rd 2.344,2.823 2.802,3.021 0.458,0.198 10 false 5th 2.74,2.823 3.104,3.146 0.365,0.323 10 false 4th 3.313,2.823 4.938,3.229 1.625,0.406 10 false 5th (Brake Operating) 5.271,2.823 5.677,3.188 0.406,0.365 10 false 6th 5.823,2.708 6.906,3.094 1.083,0.385 10 false without Control 5.833,3.198 6.854,3.552 1.021,0.354 10 false with Control 1.438,3.323 1.771,3.615 0.333,0.292 10 false 4th 2.01,3.323 2.344,3.625 0.333,0.302 10 false 3rd 3.031,3.333 3.427,3.656 0.396,0.323 10 false 4th 4.198,3.323 4.531,3.646 0.333,0.323 10 false 3rd 4.677,3.323 5,3.646 0.323,0.323 10 false 4th 5.135,3.323 5.448,3.677 0.313,0.354 10 false 5th 5.448,3.323 5.76,3.656 0.313,0.333 10 false 6th


iv.

The higher gear settings have been added for high speed gears (5th and 6th gears). In order to balance the reduction of additional drive force and the improvement of fuel efficiency when driving at high speeds, a high speed gear effective utilization control is used.


v.

By calculating the maximum additional drive force to be generated at high speed gears in a real-time manner, as well as determining the availability of high speed gears according to driving conditions (running resistance, driver's acceleration maneuvers), "balanced, improved fuel efficiency and driving capability" have been achieved.

·

Conditions Determining that Running in 6th Gear is Impossible (Examples)

X127573E04
1.021,1.833 2.542,2.219 1.521,0.385 10 false Heavy Load: 5th Gear 4.396,1.938 6.604,2.333 2.208,0.396 10 false Accelerating on Slope: 5th Gear

·

Conditions Determining that Running in 6th Gear is Possible

X127574E04
1.094,1.813 2.708,2.219 1.615,0.406 10 false Light Load: 6th Gear 4.26,1.969 6.646,2.385 2.385,0.417 10 false Constant Driving on Slope: 6th Gear




i.

Multi-mode Automatic Transmission

i.

The driver can select the desired gear step by moving the shift lever "+" (forward) or to "-" (backward) while the shift lever is in S (6-speed sequential shiftmatic mode). Thus, the driver is able to change gear steps with a manual-like feel.


ii.

6-speed sequential shiftmatic mode can be selected from normal driving mode by moving theshift lever to S. The driver can change the gear step by selecting it using the shift lever.


iii.

The driver selects 6-speed sequential shiftmatic mode by moving the shift lever to S. At this time, the S4 or S5 range isselected in accordance with the vehicle speed.


iv.

The ECM will restrict the changing of the shift range if it detects a malfunction in the automatic transmission system.


v.

If the vehicle speed and engine speed exceed or go below a preset level in response to the driver's downshift operation request, changing the shift range will be prohibited. In this case, the buzzer in the combination meter will sound to alert the driver.

System Diagram
X138350E01
5.302,6.427 5.135,6.427 5.135,6.427 4.99,5.76 true 5.344,6.313 7.104,6.688 1.76,0.375 10 false Automatic Transmission 3.229,5.156 4.063,5.604 0.833,0.448 10 false Engine 5.542,3.708 6.802,4.635 1.26,0.927 10 false Solenoid Valve Control Signals 4.781,3.688 5.417,4.844 0.635,1.156 10 false Fluid Pressure Control Signals 3.375,3.677 4.656,4.677 1.281,1 10 false Ignition Advance Control Signals 3.698,3.115 4.969,3.417 1.271,0.302 10 false ECM 0.719,0.719 2.583,1.083 1.865,0.365 10 false Combination Meter Assembly 0.615,1.208 2.75,1.594 2.135,0.385 10 false Shift Position Indicator Light "S" 0.958,1.656 2.75,2.021 1.792,0.365 10 false Shift Range Indicator 4.042,0.302 5.906,0.667 1.865,0.365 10 false Transmission Control Switch 3.344,1 4.333,1.76 0.99,0.76 10 false Shift-up Signal ("+" Position) 4.385,1.01 5.438,1.729 1.052,0.719 10 false Shift-down Signal ("-" Position) 5.552,1.01 6.625,1.698 1.073,0.688 10 false S Mode Position Signal 0.625,2.219 1.521,2.698 0.896,0.479 10 false CAN (V Bus)


vi.

The shift lever position is indicated by the shift position indicator light of the combination meter assembly. When S position is selected, the shift range indicator of the combination meter assembly displays the current shift range.


vii.

Blipping downshift control is used to improve shift change response and shift feeling in 6- speed sequential shiftmatic mode.


viii.

The blipping downshift control regulates each clutch and brake using the clutch to clutch pressure control, allowing them to be engaged smoothly and disengaged quickly. In addition, engine speed is boosted by powertrain cooperative control, thus ensuring engine brake force. In this way, a smooth and quick downshift is achieved. In addition, quicker downshifting has been made available by directly controlling clutch pressure.

HINT:

If ATF and engine coolant temperatures are low, the shift change response will be the same as when blipping downshift control is not available.


X127086E04
0.813,1.615 1.802,1.958 0.99,0.344 10 false Engine Speed 0.823,2.427 2.583,2.771 1.76,0.344 10 false Blipping Downshift Control 0.542,2.781 2.563,3.198 2.021,0.417 10 false Conventional Downshift Control 2.625,0.76 4.198,1.073 1.573,0.313 10 false Downshift Operation 4.948,0.094 6.802,0.448 1.854,0.354 10 false : Blipping downshift control 4.948,0.479 7.01,0.833 2.063,0.354 10 false : Conventional downshift control 5.448,2.458 7.073,2.844 1.625,0.385 10 false : Gear shift initiation time 5.448,2.927 6.75,3.344 1.302,0.417 10 false : Gear shift time 4.323,2.271 5.031,2.667 0.708,0.396 10 false Time 4.375,1.813 4.854,2.167 0.479,0.354 10 false 3rd 4.406,1.24 4.833,1.625 0.427,0.385 10 false 2nd




FUNCTION


a.

Shift Pattern Select System

i.

The shift pattern select system enables the driver to use a ECT 2nd start mode switch (combination switch assembly) to select the ECT 2nd start mode which allows the vehicle to start off in the 2nd gear, thus making it easy for the vehicle to start off on snowy, sandy or muddy terrain.


ii.

When the ECT 2nd start mode is selected while the shift lever is in D or in the S6, S5, S4, S3 or S2 range, the vehicle can start in the 2nd gear. After a start, if the shift lever is in D or in the S6, S5, S4 or S3 range, transmission will shift up automatically into 3rd, 4th, 5th or overdrive gears in the normal manner. If the shift lever is in the S2 range, the transmission will continue to operate in the 2nd gear.



b.

Drive Mode Select Function

i.

The drive mode can be selected by operating the ECT POWER mode switch or ECT 2nd start mode switch in the combination switch assembly (Integration Control and Panel Assembly).


ii.

When ECT POWER mode switch is pressed, ECT POWER mode is changed and ECT POWER mode indicator light is illuminate.


iii.

When ECT 2nd start mode switch is pressed, ECT 2nd start mode is changed and ECT 2nd start mode indicator light is illuminate.

Characteristics of Drive Mode
Drive Mode Outline
NORMAL Mode Best for easy driving.
ECT POWER Mode Optimal for sporty driving through the improved acceleration and responsiveness by changing the shifting points of the transmission from those of the NORMAL mode and controlling the throttle positions.
ECT 2nd Start Mode Allows the vehicle to start in the 2nd gear for providing an enough traction force at slippery road surfaces such as sands and snow.

X138060C01
2.177,5.073 2.313,5.073 2.313,5.073 2.583,4.563 true 3.625,5.115 3.49,5.115 3.49,5.115 3.406,4.573 true 5.115,1.104 4.979,1.104 4.979,1.104 4.188,1.885 true 1.552,3.531 1.865,3.688 0.313,0.156 10 false *1 2.021,4.969 2.333,5.125 0.313,0.156 10 false *a 3.646,5.021 3.958,5.177 0.313,0.156 10 false *b 5.146,1.01 5.458,1.167 0.313,0.156 10 false *1
*1 Combination Switch Assembly (Integration Control and Panel Assembly) - -
*a ECT POWER Mode Switch *b ECT 2nd Start Mode Switch


X138061C01
5.594,2.031 5.927,0.854 5.927,0.854 6.083,0.854 true 5.99,3.271 5.854,3.271 5.854,3.271 5.604,2.229 true 6.104,0.74 6.292,0.927 0.188,0.188 10 false *a 6.031,3.167 6.344,3.323 0.313,0.156 10 false *b
*a ECT POWER Mode Indicator Light *b ECT 2nd start Mode Indicator Light





CONSTRUCTION


a.

ATF Cooling System

i.

A water-cooled type ATF cooler and air-cooled type ATF cooler are used.

X138064C01
6.302,3.417 6.167,3.417 6.167,3.417 5.406,2.396 true 5.229,4.333 5.094,4.333 5.094,4.333 4.823,3.594 true 6.333,3.323 6.646,3.479 0.313,0.156 10 false *1 5.26,4.25 5.573,4.406 0.313,0.156 10 false *2
*1 Air Cooled Oil Cooler (Oil Cooler with Hose Assembly) *2 Water Cooled Oil Cooler (Built-in Radiator)
V100135

ATF Flow (to Water Cooled Oil Cooler (Built-in Radiator))
V100136

ATF Flow (to Air Cooled Oil Cooler (Oil Cooler with Hose Assembly))
V100137

ATF Flow (from Air Cooled Oil Cooler (Oil Cooler with Hose Assembly)) - -




b.

Torque Converter

i.

A compact, lightweight and high-capacity torque converter assembly is used. The torque converter supports lock-up clutch control, thus improving fuel economy.


ii.

Laser welding has been used for the outer periphery of the torque convertor to suppress welding distortion and stabilize flex lock-up clutch control.

X138062C01
2,0.698 2.177,0.698 2.177,0.698 2.885,1.323 false 1.854,1.615 2.031,1.615 2.031,1.615 3.583,2.375 true 1.781,3.208 1.958,3.208 1.958,3.208 3.521,4.26 true 1.781,3.927 1.958,3.927 1.958,3.927 2.896,4.563 true 5.073,4.802 4.917,4.802 4.917,4.802 3.854,3.917 true 5.313,0.688 5.156,0.688 5.156,0.688 4.125,1.417 true 1.823,0.604 1.979,0.813 0.156,0.208 10 false *1 1.688,1.521 2,1.677 0.313,0.156 10 false *2 1.604,3.094 1.917,3.25 0.313,0.156 10 false *3 1.615,3.813 1.927,3.969 0.313,0.156 10 false *4 5.115,4.698 5.427,4.854 0.313,0.156 10 false *5 5.354,0.594 5.667,0.75 0.313,0.156 10 false *6
*1 Lock-up Dumper *2 1-way Clutch
*3 Turbine Runner *4 Lock-up Clutch
*5 Stator *6 Pump Impeller




c.

Oil Pump

i.

The oil pump is operated by the torque converter assembly. The oil pump lubricates the planetary gear units and supplies operating fluid pressure for hydraulic control. The front oil pump drive gear is continually driven by the engine via the pump impeller. The pump has sufficient capacity to supply the necessary fluid pressure throughout all speed ranges, as well as in reverse.

X138063C01
1.844,2.01 2.104,0.833 2.104,0.833 2.24,0.833 true 3.323,2.281 3.458,1.302 3.458,1.302 3.594,1.302 true 4.271,2.156 4.354,1.083 4.354,1.083 4.49,1.083 true 5.74,1.531 6.063,0.667 6.063,0.667 6.198,0.667 true 4.979,2.219 5.094,0.917 5.094,0.917 5.229,0.917 true 2.26,0.729 2.573,0.885 0.313,0.156 10 false *1 3.615,1.208 3.927,1.365 0.313,0.156 10 false *2 4.5,1 4.813,1.156 0.313,0.156 10 false *3 6.219,0.563 6.531,0.719 0.313,0.156 10 false *5 5.271,0.813 5.583,0.969 0.313,0.156 10 false *4
*1 Front Oil Pump Body Sub-assembly *2 Front Oil Pump Driven Gear
*3 Front Oil Pump Drive Gear *4 Stator Shaft Assembly
*5 Oil Pump Cover - -




d.

ATF Filling Procedures

i.

An ATF filling procedure is used in order to improve the accuracy of the ATF level when the transmission is being repaired or replaced. As a result, the oil filler tube and the oil level gauge used in the conventional automatic transmission have been discontinued, eliminating the need to inspect the fluid level as a part of routine maintenance. For details about the ATF filling procedures, refer to the Repair Manual.

X138065C01
2.333,1.719 1.854,0.604 1.854,0.604 1.729,0.604 true 3.385,2.823 3.677,3.542 3.677,3.542 3.802,3.542 true 1.573,0.49 1.885,0.646 0.313,0.156 10 false *1 3.833,3.406 4.146,3.563 0.313,0.156 10 false *2
*1 Refill Plug *2 Overflow Plug




e.

Planetary Gear Unit

i.

The gear train consists of 2 multi-plate clutches, 3 multi-plate brakes, a 1-way clutch and 3 sets of planetary gears, each consisting of a sun gear, a pinion gear and a ring gear.

X138349C01
1.719,1.344 1.229,0.469 1.229,0.469 1.063,0.469 true 3.094,1.313 2.802,0.427 2.802,0.427 2.635,0.427 true 3.76,1.448 3.552,0.438 3.552,0.438 3.385,0.438 true 4.5,1.958 4.958,0.448 4.958,0.448 5.094,0.448 true 5.073,1.542 5.677,0.469 5.677,0.469 5.813,0.469 true 5.042,2.083 5.604,3.229 5.604,3.229 5.74,3.229 true 3.927,2.521 4.198,3.219 4.198,3.219 4.333,3.219 true 3.76,2.135 3.469,3.188 3.469,3.188 3.302,3.188 true 2.854,2.094 2.51,3.188 2.51,3.188 2.344,3.188 true 2.104,1.771 1.656,3.208 1.656,3.208 1.49,3.208 true 2.365,0.344 2.677,0.542 0.313,0.198 10 false *10 0.875,0.385 1.188,0.583 0.313,0.198 10 false *1 3.219,0.354 3.531,0.552 0.313,0.198 10 false *9 5.135,0.375 5.448,0.573 0.313,0.198 10 false *8 5.865,0.375 6.177,0.573 0.313,0.198 10 false *7 5.781,3.115 6.094,3.313 0.313,0.198 10 false *6 4.396,3.115 4.708,3.313 0.313,0.198 10 false *5 3.125,3.083 3.438,3.281 0.313,0.198 10 false *4 2.156,3.083 2.469,3.281 0.313,0.198 10 false *3 1.292,3.104 1.604,3.302 0.313,0.198 10 false *2
*1 No. 2 Clutch (C2) *2 No. 1 Clutch (C1)
*3 Front Planetary Gear Assembly *4 Center Planetary Gear Assembly
*5 Intermediate Shaft *6 Rear Planetary Gear Assembly
*7 No. 2 Brake (B2) *8 1-way Clutch Assembly
*9 No. 3 Brake (B3) *10 No. 1 Brake (B1)


X127089C02
2.021,1.771 1.521,2.188 true 2.667,1.885 2.396,2.344 true 3.323,2.156 3.208,2.479 true 4.792,2.438 4.667,2.094 true 5.792,2.406 5.573,2.042 true 6.667,2.104 6.281,1.781 true 0.906,1.667 0.531,1.344 true 3.042,1.427 2.927,1.104 true 4.75,1.052 4.594,1.479 true 0.385,1.188 0.656,1.438 0.271,0.25 10 false *1 1.365,2.177 1.656,2.469 0.292,0.292 10 false *2 2.25,2.344 2.552,2.594 0.302,0.25 10 false *3 3.083,2.479 3.385,2.719 0.302,0.24 10 false *4 4.76,2.448 5.313,2.635 0.552,0.188 10 false *5 5.74,2.417 6.292,2.604 0.552,0.188 10 false *6 6.667,2.094 6.927,2.344 0.26,0.25 10 false *7 4.708,0.854 5,1.104 0.292,0.25 10 false *8 2.823,0.906 3.115,1.208 0.292,0.302 10 false *9
*1 Input Shaft *2 Intermediate Shaft
*3 Front Planetary Sun Gear *4 Front Planetary Gear Assembly
*5 Center Planetary Gear Assembly *6 Rear Planetary Gear Assembly
*7 Output Shaft *8 Center Planetary Carrier
*9 Front Planetary Carrier - -




f.

Centrifugal Fluid Pressure Canceling Mechanism

i.

A centrifugal fluid pressure canceling mechanism is used on the C1 and C2 clutches that are applied when shifting 3rd-4th and 4th-5th.


ii.

Clutch shifting operation is affected not only by the valve body controlling fluid pressure but also by centrifugal fluid pressure that is present due to fluid in the clutch piston oil pressure chamber. The centrifugal fluid pressure canceling mechanism uses chamber B to reduce the effect applied to chamber A. As a result, smooth shifting with excellent response has been achieved.

X138066C01
1.281,1.125 1.115,0.594 1.115,0.594 1,0.594 true 1.146,1.563 0.698,0.865 0.698,0.865 0.583,0.865 true 0.823,2 0.677,2.865 0.677,2.865 0.563,2.865 true 1.479,2 1.708,3 1.708,3 1.833,3 true 1.729,1.885 2.417,3.021 2.417,3.021 2.542,3.021 true 2.094,1.573 2.625,0.948 2.625,0.948 2.75,0.948 true 1.719,1.542 2.354,0.719 2.354,0.719 2.479,0.719 true 1.677,1.135 1.896,0.604 1.896,0.604 2.021,0.604 true 0.833,0.49 1.021,0.667 0.188,0.177 10 false *1 0.406,0.75 0.583,0.906 0.177,0.156 10 false *2 0.406,2.74 0.719,2.896 0.313,0.156 10 false *3 1.865,2.885 2.177,3.042 0.313,0.156 10 false *4 2.542,2.927 2.854,3.083 0.313,0.156 10 false *5 2.781,0.844 3.094,1 0.313,0.156 10 false *6 2.521,0.615 2.833,0.771 0.313,0.156 10 false *7 2.052,0.5 2.365,0.656 0.313,0.156 10 false *8
*1 Piston (for C2) *2 Chamber B (for C2)
*3 Chamber A (for C2) *4 Chamber A (for C1)
*5 Chamber B (for C1) *6 No. 1 Clutch (C1)
*7 Piston (for C1) *8 No. 2 Clutch (C2)



iii.

Chamber B is filled by fluid supplied to the shaft for lubrication. As a result of filling chamber B, the same amount of fluid pressure is present on both sides of the piston due to centrifugal force. This cancels the effects of fluid pressure on the piston caused by centrifugal force. Accordingly, it is not necessary to discharge the fluid through the use of a check ball, and highly responsive and smooth shifting characteristics are achieved.

U116711E10
3.802,0.302 3.969,0.302 3.969,0.302 3.969,0.635 true 3.729,1.5 3.552,1.5 3.552,1.5 3.552,1.167 true 2.719,0.438 3,0.438 3,0.438 3,1.313 true 1.135,1.26 1.594,1.26 true 1.75,2.667 2.25,2.667 2.25,2.667 2.25,2.385 false 4.844,3.521 6.396,4.313 1.552,0.792 10 false Target fluid pressure (original clutch pressure) 2.552,3.542 4.083,4.323 1.531,0.781 10 false Centrifugal fluid pressure applied chamber B 5.063,1.729 6.688,2.594 1.625,0.865 10 false : Centrifugal fluid pressure applied to chamber B 5.063,1.083 6.688,1.802 1.625,0.719 10 false : Centrifugal fluid pressure applied to chamber A 5.042,0.448 6.75,0.917 1.708,0.469 10 false : Target fluid pressure 3.333,0.198 3.875,0.531 0.542,0.333 10 false Clutch 3.792,1.396 4.333,1.802 0.542,0.406 10 false Piston 0.875,0.323 2.646,1.094 1.771,0.771 10 false Chamber B (Centrifugal Fluid Pressure Chamber) 0.302,1.167 1.115,2.542 0.813,1.375 10 false Chamber A (Piston Fluid Pressure Chamber) 0.656,2.563 1.729,3.156 1.073,0.594 10 false Fluid Pressure Applied to Piston 2.844,2.698 3.667,3.083 0.823,0.385 10 false Shaft Side 0.771,3.521 1.802,4.313 1.031,0.792 10 false Fluid pressure applied to piston



g.

Transmission Valve Body Assembly

i.

The transmission valve body assembly consists of upper and lower valve bodies and 7 shift solenoid valves.

X127098C02
3.042,1.302 2.813,0.667 true 2.542,1.427 2.177,0.792 true 2.021,1.552 1.542,0.979 true 1.469,1.719 0.938,1.26 true 0.979,1.865 0.573,1.625 true 3.594,1.156 3.594,0.552 true 4.292,0.615 4.031,1.073 true 6.24,1.969 5.552,2.365 true 4.385,4.146 4.385,3.5 true 2.708,0.458 2.969,0.74 0.26,0.281 10 false *1 2.052,0.604 2.323,0.896 0.271,0.292 10 false *2 1.417,0.792 1.667,1.094 0.25,0.302 10 false *3 0.792,1.083 1.063,1.354 0.271,0.271 10 false *4 0.417,1.479 0.698,1.781 0.281,0.302 10 false *5 4.323,4.167 4.594,4.406 0.271,0.24 10 false *6 6.26,1.844 6.5,2.156 0.24,0.313 10 false *7 4.302,0.458 4.583,0.719 0.281,0.26 10 false *8 3.531,0.302 3.823,0.573 0.292,0.271 10 false *9
*1 Shift Solenoid Valve (SLU) *2 Shift Solenoid Valve (SL3)
*3 Shift Solenoid Valve (SL1) *4 Shift Solenoid Valve (SL2)
*5 Shift Solenoid Valve (SLT) *6 Lower Valve Body
*7 Upper Valve Body *8 Shift Solenoid Valve (SL)
*9 Shift Solenoid Valve (SL4) - -


X127100C02
1.427,0.958 0.75,0.563 true 2.083,2.792 1.302,3.25 true 2.396,2.885 1.885,3.479 true 3.583,2.302 3.156,3.49 true 4.177,2.604 4.021,3.49 true 4.792,3.479 4.646,2.625 true 5.281,3.479 5.063,2.875 true 6.448,3.052 5.5,2.51 true 6.156,0.479 5.354,0.938 true 5.448,0.333 4.906,0.792 true 4.948,0.333 4.427,0.958 true 4.271,0.333 3.958,0.865 true 3.01,1.333 2.635,0.313 true 1.927,0.906 1.458,0.344 true 2.521,0.094 2.792,0.354 0.271,0.26 10 false *1 1.323,0.167 1.625,0.427 0.302,0.26 10 false *2 0.583,0.406 0.854,0.698 0.271,0.292 10 false *3 1.125,3.188 1.438,3.469 0.313,0.281 10 false *4 1.75,3.469 2.042,3.708 0.292,0.24 10 false *5 3.052,3.49 3.292,3.719 0.24,0.229 10 false *6 3.927,3.49 4.198,3.729 0.271,0.24 10 false *7 4.74,3.49 4.958,3.708 0.219,0.219 10 false *8 5.229,3.479 5.49,3.74 0.26,0.26 10 false *9 6.479,3 6.833,3.302 0.354,0.302 10 false *10 6.167,0.344 6.49,0.646 0.323,0.302 10 false *11 5.458,0.188 5.792,0.49 0.333,0.302 10 false *12 4.885,0.125 5.188,0.375 0.302,0.25 10 false *13 4.198,0.135 4.531,0.396 0.333,0.26 10 false *14
*1 Lock-up Relay Valve *2 Secondary Regulator Valve
*3 C2 Damper *4 SLT Damper
*5 B2 Damper *6 Lock-up Control Valve
*7 B4 Apply Control Valve *8 B4 Control Valve
*9 B1, B4 Apply Control Valve *10 Solenoid Relay Valve
*11 Solenoid Modulator Valve *12 B1 Apply Control Valve
*13 Clutch Control Valve *14 Sequence Valve


X127101C02
2.292,2.396 0.969,2.875 true 4.292,1.958 3.844,3.188 true 5,3.156 4.521,2.333 true 6.219,0.802 5.125,1.198 true 0.792,2.792 1.052,3.052 0.26,0.26 10 false *1 3.729,3.188 4,3.479 0.271,0.292 10 false *2 4.979,3.167 5.24,3.438 0.26,0.271 10 false *3 6.24,0.646 6.51,0.938 0.271,0.292 10 false *4
*1 Primary Regulator Valve *2 B2 Apply Control Valve
*3 C1 Accumulator *4 B1 Damper




h.

Shift Solenoid Valves (SL1), (SL2), (SL3), (SL4), (SLT) and (SLU)

i.

Shift Solenoid Valves have been provided for controlling clutch engagement hydraulic pressure (SL1, SL2), lock-up clutch (SLU), line hydraulic pressure (SLT), and brake engagement hydraulic pressure (SL3, SL4).


ii.

By directly controlling the hydraulic pressure for each clutch and brake with high flow rate Shift Solenoid Valves (SL1), (SL2), (SL3), (SL4), shift-change responsiveness has been improved, shift shocks have been reduced, and the structure has been simplified through the reductions of oil passage lengths and the numbers of components.

Shift Solenoid Valves (SL1), (SL2), (SL3) and (SL4)
X127102E07
1.146,1.229 1.146,0.563 1.146,0.563 1.323,0.563 true 1.063,1.719 1.24,1.719 1.24,1.719 1.24,1.5 true 1.365,0.469 3.052,0.667 1.688,0.198 10 false Spool Valve 0.625,1.615 1.167,1.927 0.542,0.313 10 false Sleeve 3.698,0.708 4.292,1.708 0.594,1 10 false Hydraulic Pressure 5.573,2.104 6.188,2.438 0.615,0.333 10 false Current

Shift Solenoid Valve (SLT)
X127103E07
1.271,1.156 1.271,0.521 1.271,0.521 1.479,0.521 true 1.156,1.698 1.333,1.698 1.333,1.698 1.333,1.458 true 1.531,0.427 2.5,0.833 0.969,0.406 10 false Spool Valve 0.708,1.594 1.24,1.958 0.531,0.365 10 false Sleeve 3.688,0.521 4.281,1.813 0.594,1.292 10 false Hydraulic Pressure 5.479,2.083 6.188,2.479 0.708,0.396 10 false Current

Shift Solenoid Valve (SLU)
X127104E06
1.25,1.156 1.25,0.542 1.25,0.542 1.448,0.542 true 1.208,1.667 1.375,1.667 1.375,1.667 1.375,1.438 true 1.5,0.438 2.458,0.771 0.958,0.333 10 false Spool Valve 0.76,1.563 1.302,1.948 0.542,0.385 10 false Sleeve 3.708,0.708 4.313,1.906 0.604,1.198 10 false Hydraulic Pressure 5.583,2.094 6.25,2.448 0.667,0.354 10 false Current

Function of Shift Solenoid Valves
Shift Solenoid Valve Function
Shift Solenoid Valve (SL1) Performs shift controls.
Shift Solenoid Valve (SL2) Performs shift controls.
Shift Solenoid Valve (SL3) Performs shift controls.
Shift Solenoid Valve (SL4) Performs shift controls.
Shift Solenoid Valve (SLT) Performs line pressure controls.
Shift Solenoid Valve (SLU)
·

Performs lock-up clutch controls.

·

Performs B2 brake hydraulic pressure controls (only for the 1st range when the shift lever is in S).





i.

Shift Solenoid Valve (SL)

i.

A transmission 3-way solenoid (SL) has been provided for switching lock-up hydraulic pressure and B2 brake hydraulic pressure.

X127105E04
3.135,0.792 3.313,0.385 3.313,0.385 3.51,0.385 true 3.021,1.365 2.698,1.74 2.698,1.74 2.5,1.74 true 1.646,1.198 2.615,1.573 0.969,0.375 10 false Line Pressure 3.563,0.292 4.865,0.75 1.302,0.458 10 false Control Pressure 1.979,1.635 2.646,2.01 0.667,0.375 10 false Strainer 2.99,1.875 3.448,2.26 0.458,0.385 10 false Drain

Function of Shift Solenoid Valve
Shift Solenoid Valve Function
Shift Solenoid Valve (SL) Shifts between lock-up hydraulic pressure and B2 brake hydraulic pressure.



j.

ATF Temperature Sensor

i.

The ATF temperature sensors are used for hydraulic pressure control. These sensors are used for revision of the pressure that is used to apply clutches and brakes in the transmission. This helps to ensure smooth shift quality.

X127099C02
2.896,2.625 2.01,3.365 true 5.094,0.656 4.125,1.469 true 1.865,3.323 2.083,3.583 0.219,0.26 10 false *1 5.125,0.531 5.417,0.792 0.292,0.26 10 false *2
*1 No. 2 ATF Temperature Sensor (Transmission Wire) *2 No. 1 ATF Temperature Sensor (Transmission Wire)
V100135

Engine Side - -




k.

Park/Neutral Position Switch Assembly

i.

The park/neutral position switch assembly sends the P, R, N, D and NSW signals to the ECM.

X127057E03
0.052,0.688 0.708,1.51 0.656,0.823 10 false To Starter Relay 0.479,1.875 0.771,2.24 0.292,0.365 10 false +B 1.083,0.906 1.385,1.198 0.302,0.292 10 false L 1.354,2.958 2.667,3.74 1.313,0.781 10 false Park/Neutral Position Switch Assembly 2.844,0.906 3.146,1.219 0.302,0.313 10 false B 2.844,1.333 3.115,1.615 0.271,0.281 10 false PL 2.844,1.771 3.198,2.104 0.354,0.333 10 false RL 2.844,2.198 3.156,2.542 0.313,0.344 10 false NL 2.844,2.635 3.167,2.917 0.323,0.281 10 false DL 4.01,1.594 4.479,2.031 0.469,0.438 10 false ECM 4.198,0.583 4.625,0.927 0.427,0.344 10 false STA 3.229,0.906 3.708,1.281 0.479,0.375 10 false NSW 3.448,1.333 3.76,1.625 0.313,0.292 10 false P 3.448,1.76 3.74,2.042 0.292,0.281 10 false R 3.448,2.198 3.76,2.458 0.313,0.26 10 false N 3.448,2.635 3.708,2.938 0.26,0.302 10 false D 4.75,1.833 5.667,2.26 0.917,0.427 10 false CAN (V Bus) 5.813,1.26 6.646,2.583 0.833,1.323 10 false Combination Meter Assembly



l.

Transmission Control Switch

i.

The transmission control switch is installed inside the transmission floor shift assembly to detect the S position and inform the ECM.


ii.

The transmission control switch detects whether the shift lever is in D or S, and detects the operating conditions of the shift lever ["+" (forward) or "-" (backward)] when the shift lever is in S, and sends signals to the ECM.

X127058E03
0.302,0.677 0.615,0.969 0.313,0.292 10 false +B 1.031,0.781 1.281,1.031 0.25,0.25 10 false IG 2.51,0.771 2.792,1.021 0.281,0.25 10 false S 2.51,1.188 3.042,1.5 0.531,0.313 10 false SFTU 2.51,1.583 3.042,1.896 0.531,0.313 10 false SFTD 3.469,0.771 3.698,1.031 0.229,0.26 10 false S 3.208,1.177 3.75,1.5 0.542,0.323 10 false SFTU 3.208,1.583 3.74,1.979 0.531,0.396 10 false SFTD 0.958,2.031 2.958,2.458 2,0.427 10 false Transmission Control Switch 3.979,0.99 4.531,1.458 0.552,0.469 10 false ECM 4.76,1.24 5.677,1.656 0.917,0.417 10 false CAN (V Bus) 5.813,0.594 6.646,1.875 0.833,1.281 10 false Combination Meter Assembly



m.

Transmission Revolution Sensor

i.

This automatic transmission uses a transmission revolution sensor (for NT signal) and a transmission revolution sensor (for SP2 signal). Thus, the ECM can detect the timing of the shifting of the gears and appropriately control the engine torque and hydraulic pressure in response to various conditions.


ii.

These transmission revolution sensors are the pick-up coil type.


iii.

The transmission revolution sensor (for NT signal) detects the input speed of the transmission. The direct clutch drum sub-assembly is used as the timing rotor for this sensor.


iv.

The transmission revolution sensor (for SP2 signal) detects the output speed of the transmission. The parking lock gear on the rear planetary gear is used as the timing rotor for this sensor.

X138067C01
3.198,1.094 2.885,0.354 2.885,0.354 2.76,0.354 true 4.042,1.188 3.677,0.302 3.677,0.302 3.552,0.302 true 3.573,2.094 4.125,3.396 4.125,3.396 4.281,3.396 true 4.938,1.75 5.469,3.167 5.469,3.167 5.625,3.167 true 2.594,0.24 2.781,0.438 0.188,0.198 10 false *1 4.323,3.292 4.635,3.448 0.313,0.156 10 false *2 5.667,3.063 5.979,3.219 0.313,0.156 10 false *3 3.385,0.198 3.552,0.375 0.167,0.177 10 false *4
*1 Direct Clutch Drum Sub-assembly *2 Transmission Revolution Sensor (NT)
*3 Parking Lock Gear *4 Transmission Revolution Sensor (SP2)





OPERATION


a.

Transmission Power Flow

i.

1st Gear (Shift Lever in D or S)

X127090C01
0,0 0,0 false
V100144

Operates
V100143

Operates during Engine Braking



ii.

2rd Gear (Shift Lever in D or S)

X127091C01
0,0 0,0 false
V100144

Operates - -



iii.

3rd Gear (Shift Lever in D or S)

X127092C01
0,0 0,0 false
V100144

Operates - -



iv.

4th Gear (Shift Lever in D or S)

X127093C01
0,0 0,0 false
V100144

Operates - -



v.

5th Gear (Shift Lever in D or S)

X127094C01
0,0 0,0 false
V100144

Operates - -



vi.

6th Gear (Shift Lever in D or S)

X127095C01
0,0 0,0 false
V100144

Operates - -



vii.

Reverse Gear (Shift Lever in R)

X127096C01
0,0 0,0 false
V100144

Operates - -





FAIL-SAFE


a.

The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or a shift solenoid valve.


b.

For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section. Furthermore, the ECM illuminates or blinks the MIL in the combination meter assembly to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs can be read by connecting a Global TechStream (GTS) to the DLC3.


c.

For details, refer to the Repair Manual.



SHIFT CONTROL MECHANISM


a.

General

i.

A gate type shift lever that uses a transmission control rod is used.


ii.

The shift control mechanism consists of a transmission floor shift assembly and a floor shift gearshifting rod sub-assembly.

X138068C01
3.854,1.979 3.281,1.052 3.281,1.052 3.146,1.052 true 2.51,3.188 1.938,2.26 1.938,2.26 1.802,2.26 true 4.229,0.75 4.698,0.25 4.698,0.25 4.865,0.25 true 2.958,0.938 3.271,1.094 0.313,0.156 10 false *1 4.906,0.135 5.219,0.292 0.313,0.156 10 false *2 1.625,2.156 1.938,2.313 0.313,0.156 10 false *3 6.24,5.188 6.552,5.344 0.313,0.156 10 false *a
*1 Transmission Floor Shift Assembly *2 Shift Lever Knob Sub-assembly
*3 Floor Shift Gear Shifting Rod Sub-assembly - -
*a Shift Pattern - -




b.

Shift Lock System

i.

The shift lock system prevents the shift lever from being moved to any position other than P, unless the engine switch (push start switch) is turned on (IG) and the brake pedal is depressed. This prevents the vehicle from starting off suddenly.


ii.

The shift lock system is controlled by the shift lock control ECU, and it has a shift lock function.


iii.

The shift lock control ECU has a built-in P detection switch to detect the shift lever position, and receives input signals from the stop light switch assembly and engine switch (push start switch) . Upon receiving these signals, the shift lock control ECU turns on the shift lock solenoid in order to release the shift lock.

System Diagram
X132302E03
0.573,2.99 2.083,3.542 1.51,0.552 10 false Engine Switch (Push Start Switch) 0.49,1.406 2.021,2.365 1.531,0.958 10 false Certification ECU (Smart Key ECU Assembly) 0.698,0.281 1.823,1.188 1.125,0.906 10 false Stop Light Switch Assembly 3.073,1.177 4.656,1.667 1.583,0.49 10 false Shift Lock Control ECU 5.521,0.594 6.813,1.021 1.292,0.427 10 false Shift Lock Solenoid 5.563,1.719 6.906,2.177 1.344,0.458 10 false P Detection Switch 3.969,2.583 6.667,2.979 2.698,0.396 10 false Transmission Floor Shift Assembly

Parts Location
X138348C01
0.51,0.448 1.781,1.448 1.271,1 2.26,2.698 2.771,1.094 2.771,1.094 2.938,1.094 true 0.969,3.042 0.51,1.823 0.51,1.823 0.333,1.823 true 2.615,3.573 2.052,4.323 2.052,4.323 1.875,4.323 true 5.323,2.854 4.948,3.458 4.948,3.458 4.771,3.458 true 5.469,2.823 5.313,3.74 5.313,3.74 5.135,3.74 true 5.729,3.083 5.656,4.01 5.656,4.01 5.479,4.01 true 5.365,2.552 5.031,1.458 5.031,1.458 4.854,1.458 true 5.406,2.625 5.719,1.469 5.719,1.469 5.885,1.469 true 1.146,1.135 1.458,1.333 0.313,0.198 10 false *1 0.615,1.208 0.927,1.406 0.313,0.198 10 false *a 2.958,1.01 3.271,1.208 0.313,0.198 10 false *2 0.167,1.719 0.479,1.917 0.313,0.198 10 false *3 1.688,4.219 2,4.417 0.313,0.198 10 false *4 4.604,3.365 4.917,3.563 0.313,0.198 10 false *5 4.958,3.635 5.271,3.833 0.313,0.198 10 false *6 5.292,3.906 5.604,4.104 0.313,0.198 10 false *7 4.677,1.365 4.99,1.563 0.313,0.198 10 false *9 5.896,1.375 6.208,1.573 0.313,0.198 10 false *8
*1 Certification ECU (Smart Key ECU Assembly) *2 Engine Switch (Push Start Switch)
*3 Stop Light Switch Assembly *4 Transmission Floor Shift Assembly
*5 P Detection Switch *6 Shift Lock Solenoid
*7 Shift Lock Control ECU *8 Shift Lock Release Button
*9 Shift Lock Release Button Cap - -
*a Refer to the Service Bulletin for the installation position of the part. - -




c.

Shif Lock Control

Function of Main Components
Component Function
Transmission Floor Shift Assembly Shift Lock Solenoid Locks the shift lever in P.
P Detection Switch Detects when the shift lever is in P.
Shift Lock Control ECU Controls the Shift Lock Solenoid based on signals from each switch.
Stop Light Switch Assembly Detects when the brake pedal is depressed.
Certification ECU (Smart Key ECU Assembly) Sends the engine switch signal to the shift lock control ECU.
Engine Switch (Push Start Switch) Detects the switch operation condition.


d.

System Control

i.

The shift lock control ECU uses the P detection switch to detect the shift lever position, and receives input signals from the stop light switch assembly and engine switch. Upon receiving these signals, the shift lock control ECU turns on the shift lock solenoid in order to release shift lock.



e.

Function

i.

Shift Lock Mechanism

1.

The shift lock mechanism prevents the shift lever from being moved to any position other than P, unless the engine switch is on (IG), and the brake pedal is depressed. This mechanism helps to prevent unintentional acceleration.

2.

A shift lock release button, which manually overrides the shift lock mechanism, is provided.