SYSTEM CONTROL
The cruise control has the following control:
| Control | Outline | |
|---|---|---|
| Constant Speed Control | Gasoline Engine | The ECM compares the actual vehicle speed and the set vehicle speed. If the vehicle speed is higher than the set vehicle speed, the ECM activates the throttle control motor in the throttle closing direction. If the vehicle speed is lower than the set vehicle speed, the ECM activates the throttle control motor in the throttle opening direction. |
| Diesel Engine | The ECM compares the actual vehicle speed and the set vehicle speed. If the vehicle speed is higher than the set vehicle speed, the ECM decreases the injection volume by regulating the injectors via the injector drivers. If the vehicle speed is lower than the set vehicle speed, the ECM increases the injection volume by regulating the injectors via the injector drivers. | |
| Set Control | When this system fulfills the following conditions, and the cruise control main switch is moved to the -SET side and released, the ECM stores the vehicle speed and illuminates the cruise control SET indicator light on the combination meter assembly and maintains the vehicle constantly at that speed.
·
ON-OFF button on the cruise control main switch is pressed. ·
The vehicle is running at a vehicle speed of approx. 40 km/h (25 mph) or more. |
|
| Low Speed Limit Control | The low speed limit is approx. 40 km/h (25 mph). If the vehicle speed drops below that speed while running in the cruise control, the cruise control will be canceled automatically. However, the set vehicle speed in the memory is kept. | |
| High Speed Limit Control | The high speed limit is a highest speed that cruise control mode can be set and is designed at approx. 200 km/h (125 mph).
·
The cruise control mode cannot be set if the vehicle speed exceeds the high speed limit. ·
The vehicle will not accelerate when the +RES switch is operated if the vehicle speed exceeds the high speed limit. |
|
| COAST (-) Switch Control | While the cruise control main switch is held to the -SET side, the vehicle speed and the set vehicle speed change as follows:
·
The vehicle decelerates constantly. ·
The set vehicle speed changes to the speed at which the switch is released. |
|
| Tap Down Control | When the cruise control main switch is pushed momentarily (approx. 0.6 seconds) to the -SET side, the vehicle speed and the vehicle setting speed change as follows:
·
The vehicle will decelerate in increments of approx. 1.0 km/h (1 mph)*1 or 1.6 km/h (1 mph)*2 for each time the switch is pressed. ·
However, if the difference between the actual vehicle speed and the vehicle setting speed is greater than 5 km/h (3 mph), the vehicle setting speed will change to the speed at which the vehicle was being driven at the time the switch was released. |
|
| ACC (+) Switch Control | When the cruise control main switch is held to the +RES side, the vehicle speed and the set vehicle speed change as follows:
·
The vehicle accelerates constantly. ·
The set vehicle speed changes to the speed at which the switch is released. |
|
| Tap Up Control | When the cruise control main switch is pushed momentarily (approx. 0.6 seconds) to the +RES side, the vehicle speed and the vehicle setting speed change as follows:
·
The vehicle accelerates in increments of approx. 1.0 km/h (1 mph)*1 or 1.6 km/h (1 mph)*2 for each time the switch is pressed. ·
However, if the difference between the actual vehicle speed and the vehicle setting speed is greater than 5 km/h (3 mph), the vehicle setting speed does not change. |
|
| RES Switch Control | If the cruise control is canceled for any reason other than a malfunction (except cancellation by operating the ON-OFF button on the cruise control main switch) and the vehicle speed is more than the low speed limit, the vehicle is returned to the speed set before the cancellation of cruise operation by moving the cruise control main switch to the +RES side. The cruise control mode can be resumed even if the vehicle speed drops below the low speed limit, because the set vehicle speed in the memory has not been cleared. | |
| Shift Down Control*3 | When the vehicle is cruising uphill, shift down control may be performed by the ECT (Electronic Control Transmission). If the gear has been shifted down, it will be shifted back up after a short time after the ECM judges that the upward slope has finished. | |
| Manual Cancel Control | If any of the following signals is sent to the ECM, the cruise control is canceled accordingly. However, the set vehicle speed remains in the memory.
·
Stop light switch on signal (the brake pedal is depressed). ·
Shift lever is shifted from D or S to any other position.*3 ·
When 1st, 2nd or 3rd range is selected in S position.*3 ·
Clutch switch off signal (the clutch pedal is depressed).*4 ·
CANCEL switch on signal (the cruise control main switch is moved to CANCEL side). ·
Cruise control main switch (ON-OFF button) off signal (the set vehicle speed in the memory is cleared). |
|
| Automatic Cancel Control | If the following conditions occur during cruise control driving, the speed that is set in the memory is cleared and the cruise control is canceled:
·
Stop light switch open or short circuit. Furthermore, the cruise control indicator light will turn off until the ON-OFF button on the cruise control main switch is used to turn the system off, and the operation of the cruise control will be disabled until the ignition switch is turned ON again. At this moment, [Cruise Control Malfunction Visit Your Dealer] is displayed on the multi-information display.*5 |
|
| If the following condition occurs during cruise control driving, the speed that is set in the memory is cleared and the cruise control is canceled:
·
Malfunction in the engine control system. Furthermore, the cruise control indicator light will turn off until the ON-OFF button on the cruise control main switch is used to turn the system off, and the operation of the cruise control will be disabled until the ignition switch is turned ON again. |
||
| If any of the following conditions occur during cruise control driving, the speed that is set in the memory is cleared and the cruise control is cancelled:
·
Stop light switch input signal is abnormal. ·
Cancel circuit is malfunctioning. ·
Brake control system malfunction. ·
Communication malfunction between the skid control ECU and ECM. Furthermore, the cruise control indicator light will turn off until the ON-OFF button on the cruise control main switch is used to turn the system off, and the operation of the cruise control will be disabled until the ignition switch is turned ON again. At this moment, [Cruise Control Malfunction Visit Your Dealer] is displayed on the multi-information display.*5 |
||
| If the following condition occurs during cruise control driving, the speed that is set in the memory is cleared and the cruise control is canceled:
·
Vehicle speed decreases by approx. 16 km/h (10 mph) or more below the speed at which the cruise control was set. |
||
| If the following condition occurs during cruise control driving, the cruise control is canceled accordingly. However, the set vehicle speed remains in the memory.
·
Vehicle speed decreases below the low speed limit (approx. 40 km/h (25 mph)). |
||
| Other Cancel Control | If any of the following conditions occur during cruise control driving, the ECM cancels the cruise control while retaining the set vehicle speed in its memory.
·
VSC is activated.*8 ·
TRC is activated for a period of time.*8 ·
When the VSC or TRC system is turned off.*8 ·
4WD control ECU assembly requests to cancel the cruise control system. When the ignition switch is turned off, the set vehicle speed is not stored in the memory. |
|
*1: Except models with 1GR-FE engine with manual transmission
*2: Models with 1GR-FE engine with manual transmission
*3: Models with automatic transmission
*4: Models with manual transmission
*5: Models with optitron display type combination meter assembly
*6: Models without entry and start system
*7: Models with entry and start system
*8: Models with VSC
PRECAUTION
Ignition Switch Expressions
The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.
| Expressions | Ignition Switch (Position) | Engine Switch (Condition) |
|---|---|---|
| Ignition Switch off | LOCK | Off (LOCK) |
| Ignition Switch ACC | ACC | On (ACC) |
| Ignition Switch ON | ON | On (IG) |
| Engine Start | START | On (Start) |