Home › General › INTRODUCTION › HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS
RM2660E _V1 General _052769 INTRODUCTION _0254793 HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS F

INTRODUCTION  HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS  ELECTRONIC CIRCUIT INSPECTION PROCEDURE  


BASIC INSPECTION


a.

WHEN MEASURING RESISTANCE OF ELECTRONIC PARTS

i.

Unless otherwise stated, all resistance measurements should be made at an ambient temperature of 20°C (68°F). Resistance measurements may be inaccurate if measured at high temperatures, i.e. immediately after the vehicle has been running. Measurements should be made after the engine has cooled down.



b.
D100803E24
1.99,2.385 2.865,2.531 0.875,0.146 10 false INCORRECT 2.406,3.063 3.281,3.208 0.875,0.146 10 false INCORRECT 2.031,3.938 2.75,4.083 0.719,0.146 10 false CORRECT

HANDLING CONNECTORS

i.

When disconnecting a connector, first squeeze the mating halves tightly together to release the lock, and then press the lock claw and separate the connector.


ii.

When disconnecting a connector, do not pull on the harnesses. Grasp the connector directly and separate it.


iii.

Before connecting a connector, check that there are no deformed, damaged, loose or missing terminals.


iv.

When connecting a connector, press firmly until it locks with a "click" sound.


v.

If checking a connector with a TOYOTA electrical tester, check the connector from the backside (harness side) using a mini test lead.

NOTICE:
·

As a waterproof connector cannot be checked from the backside, check it by connecting a sub-harness.

·

Do not damage the terminals by moving the inserted tester needle.





c.
D100734E34
2.938,0.917 2.885,1.156 false 2.156,0.646 1.917,0.677 1.917,0.677 1.24,0.115 false 1.875,0.354 2.115,0.156 false 2.188,0.073 2.865,0.24 0.677,0.167 10 false Core Wire 2.531,1.125 3.333,1.49 0.802,0.365 10 false Terminal Deformation 1.375,1.698 2.094,1.875 0.719,0.177 10 false Pull Lightly 0.385,0.021 1.24,0.396 0.854,0.375 10 false Looseness of Crimping

CHECKING CONNECTORS

i.

Checking when a connector is connected: Squeeze the connectors together to confirm that they are fully connected and locked.


ii.

Checking when a connector is disconnected: Check by pulling the wire harness lightly from the backside of the connector. Look for unlatched terminals, missing terminals, loose crimps or broken conductor wires. Check visually for corrosion, metallic or foreign matter and water, and bent, rusted, overheated, contaminated, or deformed terminals.


iii.
D100735

Checking the contact pressure of the terminal: Prepare a spare male terminal. Insert it into a female terminal, and check for ample tension when inserting and after full engagement.

NOTICE:

When testing a gold-plated female terminal, always use a gold-plated male terminal.




d.
D100736E07
2.208,0.354 3.115,0.521 0.906,0.167 10 false INCORRECT 0.583,0.354 1.313,0.531 0.729,0.177 10 false CORRECT

REPAIR METHOD OF CONNECTOR TERMINAL

i.

If there is any foreign matter on the terminal, clean the contact point using an air gun or cloth. Never rub the contact point using sandpaper as the plating may come off.


ii.

If there is abnormal contact pressure, replace the female terminal. If the male terminal is gold-plated (gold color), use a gold-plated female terminal; if it is silver-plated (silver color), use a silver-plated female terminal.


iii.

Damaged, deformed, or corroded terminals should be replaced. If the terminal does not lock into the housing, the housing may have to be replaced.



e.
D100784E06
1.76,1.865 2.635,2.01 0.875,0.146 10 false INCORRECT 1.927,0.031 2.802,0.198 0.875,0.167 10 false INCORRECT 0.25,0.052 1.125,0.219 0.875,0.167 10 false INCORRECT

HANDLING OF WIRE HARNESS

i.

If removing a wire harness, check the wiring and clamping before proceeding so that it can be restored in the same way.


ii.

Never twist, pull or slacken the wire harness more than necessary.


iii.

The wire harness should never come into contact with a high temperature part, or rotating, moving, vibrating or sharp-edged parts. Avoid contact with panel edges, screw tips and other sharp items.


iv.

When installing parts, never pinch the wire harness.


v.

Never cut or break the cover of the wire harness. If it is cut or broken, replace it or repair it with vinyl tape.




CHECK FOR OPEN CIRCUIT


U116397E02
0.135,0.094 0.563,0.292 0.427,0.198 10 false Fig. 1 1.052,0.365 1.479,0.531 0.427,0.167 10 false OPEN 0.74,0.365 0.896,0.51 0.156,0.146 10 false C 1.656,0.354 1.802,0.521 0.146,0.167 10 false B 2.531,0.396 2.698,0.573 0.167,0.177 10 false A 2.823,0.313 3.177,0.479 0.354,0.167 10 false ECU 0.177,1.354 0.844,1.542 0.667,0.188 10 false SENSOR 2.51,0.781 2.635,0.948 0.125,0.167 10 false 1 1.521,1.052 1.646,1.24 0.125,0.188 10 false 2 1.833,0.781 2,0.948 0.167,0.167 10 false 1 1.854,1.052 1.979,1.24 0.125,0.188 10 false 2 1.51,0.781 1.635,0.958 0.125,0.177 10 false 1 0.875,1.042 1,1.229 0.125,0.188 10 false 2 0.854,0.792 1.021,0.958 0.167,0.167 10 false 1 2.51,1.021 2.635,1.208 0.125,0.188 10 false 2

a.

For an open circuit in the wire harness in Fig. 1, check the resistance or voltage, as described below.


b.
U116398E02
0.125,0.104 0.542,0.281 0.417,0.177 10 false Fig. 2 2.719,0.615 3.083,0.792 0.365,0.177 10 false ECU 2.281,1.156 2.438,1.344 0.156,0.188 10 false 1 2.323,1.354 2.469,1.563 0.146,0.208 10 false 2 1.813,1.167 1.969,1.354 0.156,0.188 10 false 1 1.823,1.354 1.969,1.563 0.146,0.208 10 false 2 1.063,1.146 1.219,1.333 0.156,0.188 10 false 1 1.063,1.365 1.208,1.573 0.146,0.208 10 false 2 0.135,1.635 0.771,1.802 0.635,0.167 10 false SENSOR 0.823,1.552 0.99,1.719 0.167,0.167 10 false C 1.677,1.625 1.823,1.792 0.146,0.167 10 false B 2.552,1.542 2.708,1.719 0.156,0.177 10 false A

Check the resistance.

i.

Disconnect connectors A and C and measure the resistance between them.

Standard Resistance (Fig. 2):
Tester Connection Specified Condition
Connector A terminal 1 - Connector C terminal 1 10 kΩ or higher
Connector A terminal 2 - Connector C terminal 2 Below 1 Ω


HINT:

Measure the resistance while lightly shaking the wire harness vertically and horizontally.

If the results match the examples above, an open circuit exists between terminal 1 of connector A and terminal 1 of connector C.



ii.
U116399E02
0.125,0.083 0.521,0.271 0.396,0.188 10 false Fig. 3 0.135,0.729 0.771,0.875 0.635,0.146 10 false SENSOR 2.906,0.542 3.229,0.708 0.323,0.167 10 false ECU 0.521,1.823 0.698,2.01 0.177,0.188 10 false C 2.51,1.438 2.677,1.625 0.167,0.188 10 false 1 2.115,1.448 2.281,1.635 0.167,0.188 10 false 1 2.615,1.635 2.74,1.802 0.125,0.167 10 false 2 2.01,1.646 2.135,1.813 0.125,0.167 10 false 2 0.813,1.427 0.979,1.615 0.167,0.188 10 false 1 1.208,1.438 1.375,1.625 0.167,0.188 10 false 1 1.323,1.635 1.448,1.802 0.125,0.167 10 false 2 0.698,1.646 0.823,1.813 0.125,0.167 10 false 2 1.365,1.854 1.573,2.031 0.208,0.177 10 false B2 1.844,1.865 2.083,2.021 0.24,0.156 10 false B1 2.76,1.823 2.906,1.99 0.146,0.167 10 false A

Disconnect connector B and measure the resistance between the connectors.

Standard Resistance (Fig. 3):
Tester Connection Specified Condition
Connector A terminal 1 - Connector B1 terminal 1 Below 1 Ω
Connector B2 terminal 1 - Connector C terminal 1 10 kΩ or higher


If the results match the examples above, an open circuit exists between terminal 1 of connector B2 and terminal 1 of connector C.




c.
U116400E02
0.146,0.094 0.563,0.302 0.417,0.208 10 false Fig. 4 2.677,0.615 3.021,0.802 0.344,0.188 10 false ECU 1.479,1.021 1.781,1.198 0.302,0.177 10 false 5 V 2.323,0.729 2.635,0.906 0.313,0.177 10 false 5 V 0.906,0.833 1.198,1.021 0.292,0.188 10 false 0 V 0.198,0.927 0.844,1.115 0.646,0.188 10 false SENSOR 2.135,1.135 2.281,1.323 0.146,0.188 10 false 1 1.792,1.083 1.938,1.271 0.146,0.188 10 false 1 2.417,1.344 2.521,1.49 0.104,0.146 10 false 2 1.885,1.333 2.021,1.5 0.135,0.167 10 false 2 1.604,1.344 1.729,1.521 0.125,0.177 10 false 2 1.073,1.344 1.208,1.51 0.135,0.167 10 false 2 1.021,1.583 1.188,1.771 0.167,0.188 10 false C 2.406,1.583 2.552,1.76 0.146,0.177 10 false A 1.75,1.604 1.896,1.771 0.146,0.167 10 false B

Check the voltage.

i.

In a circuit in which voltage is applied to the ECU connector terminal, an open circuit can be checked by conducting a voltage check.

With each connector still connected, measure the voltage between the body ground and these terminals (in this order): 1) terminal 1 of connector A; 2) terminal 1 of connector B; and 3) terminal 1 of connector C.

Standard Voltage (Fig. 4):
Tester Connection Specified Condition
Connector A terminal 1 - Body ground 5 V
Connector B terminal 1 - Body ground 5 V
Connector C terminal 1 - Body ground Below 1 V


If the results match the examples above, an open circuit exists in the wire harness between terminal 1 of connector B and terminal 1 of connector C.





CHECK FOR SHORT CIRCUIT


U116401E02
0.146,0.104 0.573,0.302 0.427,0.198 10 false Fig. 5 1.156,0.406 1.708,0.583 0.552,0.177 10 false SHORT 2.771,0.344 3.135,0.542 0.365,0.198 10 false ECU 0.854,1.385 0.99,1.552 0.135,0.167 10 false C 1.688,1.396 1.833,1.583 0.146,0.188 10 false B 2.458,1.365 2.583,1.531 0.125,0.167 10 false A 2.458,0.865 2.604,1.052 0.146,0.188 10 false 1 2.458,1.125 2.563,1.302 0.104,0.177 10 false 2 1.833,0.865 1.979,1.052 0.146,0.188 10 false 1 1.854,1.115 1.958,1.292 0.104,0.177 10 false 2 0.896,0.865 1.042,1.052 0.146,0.188 10 false 1 0.917,1.135 1.021,1.313 0.104,0.177 10 false 2

a.

If the wire harness is ground shorted (Fig. 5), locate the section by conducting a resistance check with the body ground (below).


b.
U116402E02
0.125,0.094 0.573,0.281 0.448,0.188 10 false Fig. 6 0.219,0.958 0.885,1.135 0.667,0.177 10 false SENSOR 2.802,0.646 3.135,0.833 0.333,0.188 10 false ECU 0.875,1.583 1.052,1.75 0.177,0.167 10 false C 1.771,1.667 1.948,1.833 0.177,0.167 10 false B 2.594,1.583 2.74,1.74 0.146,0.156 10 false A 2.333,1.177 2.438,1.365 0.104,0.188 10 false 1 1.927,1.167 2.031,1.354 0.104,0.188 10 false 1 1.177,1.146 1.281,1.333 0.104,0.188 10 false 1 2.385,1.396 2.5,1.583 0.115,0.188 10 false 2 1.927,1.406 2.042,1.594 0.115,0.188 10 false 2 1.135,1.385 1.25,1.573 0.115,0.188 10 false 2

Check the resistance with the body ground.

i.

Disconnect connectors A and C and measure the resistance.

Standard Resistance (Fig. 6):
Tester Connection Specified Condition
Connector A terminal 1 - Body ground Below 1 Ω
Connector A terminal 2 - Body ground 10 kΩ or higher


HINT:

Measure the resistance while lightly shaking the wire harness vertically and horizontally.

If your results match the examples above, a short circuit exists between terminal 1 of connector A and terminal 1 of connector C.



ii.
U116403E02
0.125,0.083 0.51,0.302 0.385,0.219 10 false Fig. 7 0.146,0.969 0.813,1.167 0.667,0.198 10 false SENSOR 2.927,0.75 3.271,0.917 0.344,0.167 10 false ECU 2.438,1.229 2.563,1.417 0.125,0.188 10 false 1 2.063,1.229 2.208,1.396 0.146,0.167 10 false 1 2.469,1.417 2.604,1.583 0.135,0.167 10 false 2 2.063,1.417 2.198,1.583 0.135,0.167 10 false 2 1.417,1.229 1.521,1.375 0.104,0.146 10 false 1 1.01,1.208 1.125,1.385 0.115,0.177 10 false 1 1.448,1.417 1.583,1.583 0.135,0.167 10 false 2 0.979,1.406 1.115,1.573 0.135,0.167 10 false 2 0.76,1.594 0.885,1.771 0.125,0.177 10 false C 2.698,1.604 2.844,1.792 0.146,0.188 10 false A 1.885,1.646 2.094,1.833 0.208,0.188 10 false B1 1.51,1.646 1.74,1.802 0.229,0.156 10 false B2

Disconnect connector B and measure the resistance.

Standard Resistance (Fig. 7):
Tester Connection Specified Condition
Connector A terminal 1 - Body ground 10 kΩ or higher
Connector B2 terminal 1 - Body ground Below 1 Ω


If the results match the examples above, a short circuit exists between terminal 1 of connector B2 and terminal 1 of connector C.





CHECK AND REPLACE ECU


NOTICE:
·

The connector should not be disconnected from the ECU. Perform the inspection from the backside of the connector on the wire harness side.

·

When no measuring condition is specified, perform the inspection with the engine stopped and the engine switch on.

·

Check that the connectors are fully seated. Check for loose, corroded or broken wires.



a.

First, check the ECU ground circuit. If it is faulty, repair it. If it is normal, the ECU could be faulty. Temporarily replace the ECU with a normally functioning one and check if the symptoms occur. If the trouble symptoms disappear, replace the original ECU.

i.
D100801E09
1.698,0.417 1.406,0.594 1.406,0.594 1.208,0.594 false 0.073,0.063 0.813,0.25 0.74,0.188 10 false Example: 0.667,0.5 1.24,0.677 0.573,0.177 10 false Ground

Measure the resistance between the ECU ground terminal and body ground.

Standard Resistance:

Below 1 Ω



ii.
D101830E07
0.688,2.927 1.042,3.146 true 0.688,1.115 1.219,1.375 true 0.073,0.083 2.76,0.448 2.688,0.365 10 false Component without harness connected: (ECU) 0.094,1.667 2.479,2.01 2.385,0.344 10 false Rear view of wire harness connector: (to ECU) 0.219,2.833 0.781,3.01 0.563,0.177 10 false Ground 0.188,1.01 0.75,1.188 0.563,0.177 10 false Ground

Disconnect the ECU connector. Check the ground terminal on the ECU side and wire harness side for bending, corrosion or foreign matter. Lastly, check the contact pressure of the female terminals.