Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › RELAY › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254982 RELAY G

1UR-FE ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT AIR PUMP HEATER RELAY (AI-PMP HTR)

a.
A184106E12
2.542,1.104 2.938,1.104 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 2.INSPECT AIR INJECTION VSV RELAY (AI-VSV)

a.
A184106E12
2.542,1.104 2.938,1.104 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 3.INSPECT NO. 1 INTEGRATION RELAY (IG2)

a.

Measure the resistance of the IG2 MAIN fuse.

i.

Remove the IG2 MAIN fuse from the No. 1 integration relay.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 MAIN fuse Always Below 1 Ω


If the result is not as specified, replace the IG2 MAIN fuse.


iii.

Install the IG2 MAIN fuse to the No. 1 integration relay.



b.
U163348E01
0.432,1.585 0.659,1.767 0.227,0.181 10 1C 1.289,1.587 1.508,1.755 0.219,0.168 10 1B 0.118,0.089 0.345,0.322 0.227,0.233 10 *a

Measure the resistance of the ignition relay No. 2 (IG2) circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-8 Battery voltage is not applied to terminals 1B-6 and 1B-7 10 kΩ or higher
Battery voltage is applied to terminals 1B-6 and 1B-7 Below 1 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Integration Relay)

If the result is not as specified, replace the No. 1 integration relay.



Hide 4.INSPECT NO. 1 INTEGRATION RELAY (EFI)

a.

Measure the resistance of the EFI MAIN fuse.

i.

Remove the EFI MAIN fuse from the No. 1 integration relay.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN fuse Always Below 1 Ω


If the result is not as specified, replace the EFI MAIN fuse.


iii.

Install the EFI MAIN fuse to the No. 1 integration relay.



b.
U163348E01
0.432,1.585 0.659,1.767 0.227,0.181 10 1C 1.289,1.587 1.508,1.755 0.219,0.168 10 1B 0.118,0.089 0.345,0.322 0.227,0.233 10 *a

Measure the resistance of the EFI relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-4 Battery voltage is not applied to terminals 1B-2 and 1B-3 10 kΩ or higher
Battery voltage is applied to terminals 1B-2 and 1B-3 Below 1 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Integration Relay)

If the result is not as specified, replace the No. 1 integration relay.



Hide 5.INSPECT EFI NO. 2 RELAY

a.
A184106E12
2.542,1.104 2.938,1.104 false 2.542,1.615 2.948,1.615 false 1.573,0.177 1.698,0.177 1.698,0.177 2.031,0.563 false 3.031,0.177 2.906,0.177 2.906,0.177 2.625,0.552 false 0.208,0.729 0.417,0.906 0.208,0.177 10 false 3 1.208,0.729 1.406,0.906 0.198,0.177 10 false 5 0.208,1.271 0.365,1.448 0.156,0.177 10 false 2 1.208,1.271 1.438,1.448 0.229,0.177 10 false 1 3.021,1.521 3.229,1.698 0.208,0.177 10 false 3 3,1.021 3.198,1.198 0.198,0.177 10 false 5 3.094,0.083 3.25,0.26 0.156,0.177 10 false 2 1.417,0.083 1.646,0.26 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 6.INSPECT NO. 1 INTEGRATION RELAY (A/F)

a.

Measure the resistance of the A/F fuse.

i.

Remove the A/F fuse from the No. 1 integration relay.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F fuse Always Below 1 Ω


If the result is not as specified, replace the A/F fuse.


iii.

Install the A/F fuse to the No. 1 integration relay.



b.
U163349E01
2.417,1.584 2.644,1.765 0.227,0.181 10 1A 0.399,1.584 0.616,1.765 0.217,0.181 10 1C 0.118,0.087 0.345,0.320 0.227,0.233 10 *a

Measure the resistance of the air fuel ratio sensor heater relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1A-4 Battery voltage is not applied to terminals 1A-2 and 1A-3 10 kΩ or higher
Battery voltage is applied to terminals 1 A-2 and 1A-3 Below 1 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Integration Relay)

If the result is not as specified, replace the No. 1 integration relay.



Hide 7.INSPECT MAIN BODY ECU (IG1 NO. 1)

a.

Measure the resistance according to the value(s) in the table below.

A385263E01
2.99,0.521 3.271,0.719 0.281,0.198 1.542,1.375 1.802,1.552 0.26,0.177 3.531,3.583 3.802,3.771 0.271,0.188 1.302,2.802 1.302,2.042 true 2.479,2.792 2.479,1.271 2.479,1.271 2.25,1.177 true 2.99,2.813 2.99,1.469 true 4.021,5.219 4.021,4.573 4.021,4.573 3.896,4.344 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 3.042,0.542 3.354,0.74 0.313,0.198 10 false 2B 1.583,1.375 1.896,1.573 0.313,0.198 10 false 2A 3.573,3.583 3.885,3.781 0.313,0.198 10 false 2D 1.26,2.865 1.573,3.063 0.313,0.198 10 false 1 2.396,2.844 2.635,3.042 0.24,0.198 10 false 17 2.958,2.854 3.271,3.052 0.313,0.198 10 false 5 3.979,5.271 4.292,5.469 0.313,0.198 10 false 43

Text in Illustration
*a Component without harness connected
(Main Body ECU)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2A-1 - 2B-17 Battery voltage is not applied to terminals 2B-5 and 2D-43 10 kΩ or higher
Battery voltage is applied to terminals 2B-5 and 2D-43 Below 1 Ω


If the result is not as specified, replace the main body ECU.


Hide 28300D 9.INSPECT STARTER CUT RELAY (ST CUT)

Hide 82733A 10.INSPECT MAIN BODY ECU (ACC RELAY)