Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The intake camshaft VVT sensor (VV1 and VV2 signal) consists of a magnet and MRE (Magnetoresistive Element).

The intake camshaft has 3 teeth on its outer circumference. When the intake camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE fluctuates. The VVT sensor converts the camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends the data to the ECM.

The crankshaft angle sensor rotor has 34 teeth. The MRE generates 34 signals for each crankshaft revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No. DTC Detection Condition Trouble Area
P0340
P0345
No VVT sensor signal is sent to the ECM at an engine speed of 600 rpm or more (1 trip detection logic).
·

Open or short in VVT sensor circuit for intake camshaft

·

VVT sensor for intake camshaft

·

Intake camshaft

·

Timing chain for intake camshaft jumped tooth

·

ECM


P0342
P0347
Output voltage of VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor circuit for intake camshaft

·

VVT sensor for intake camshaft

·

Intake camshaft

·

Timing chain for intake camshaft jumped tooth

·

ECM


P0343
P0348
Output voltage of VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor circuit for intake camshaft

·

VVT sensor for intake camshaft

·

Intake camshaft

·

Timing chain for intake camshaft jumped tooth

·

ECM



A217926E02
0.218,1.183 0.448,1.348 0.230,0.165 10 NE 0.145,1.733 0.449,1.885 0.304,0.151 10 VV1 0.149,2.105 0.448,2.251 0.299,0.145 10 VV2 2.85,1.275 3.186,1.424 0.336,0.149 10 GND 2.85,2.195 3.186,2.344 0.336,0.149 10 GND 2.85,1.818 3.186,1.967 0.336,0.149 10 GND 1.1,2.509 2.021,2.650 0.921,0.141 10 20 msec./DIV. 2.685,0.797 3.249,0.953 0.563,0.156 10 5 V/DIV. 0.102,0.078 2.419,0.234 2.318,0.156 10 VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

Standard:
for RHD
Tester Connection Tool Setting Condition Specified Condition
C46-110 (NE+) - C46-111 (NE-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C46-92 (VV1+) - C46-91 (VV1-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C46-87 (VV2+) - C46-88 (VV2-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown

for LHD
Tester Connection Tool Setting Condition Specified Condition
C45-110 (NE+) - C45-111 (NE-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C45-92 (VV1+) - C45-91 (VV1-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C45-87 (VV2+) - C45-88 (VV2-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown


HINT:

VV1 and VV2 are the VVT sensor signals, and NE is the crankshaft position sensor signal.



MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Start the engine and run it at idle for 10 seconds or more.


WIRING DIAGRAM

A276694E05
5.165,0.815 5.580,0.980 0.415,0.165 10 VCV2 5.165,1.357 5.580,1.522 0.415,0.165 10 VV1+ 5.161,1.885 5.576,2.050 0.415,0.165 10 VV1- 5.161,3.795 5.576,3.960 0.415,0.165 10 VV2+ 5.161,4.322 5.576,4.488 0.415,0.165 10 VV2- 0.925,2.544 3.608,2.820 2.684,0.276 10 VVT Sensor (for Intake Side of Bank 1) 0.925,4.982 3.530,5.332 2.605,0.350 10 VVT Sensor (for Intake Side of Bank 2) 0.906,2.39 1.293,2.564 0.387,0.174 10 C26 0.925,4.814 1.312,4.988 0.387,0.174 10 C25 5.221,5.122 6.146,5.315 0.924,0.193 10 C46*1 C45*2 5.221,5.29 5.590,5.483 0.369,0.193 10 ECM 4.894,0.807 5.073,0.986 0.179,0.179 10 66 4.894,1.339 5.078,1.513 0.184,0.174 10 92 4.894,1.862 5.094,2.020 0.200,0.158 10 91 4.894,3.768 5.078,3.942 0.184,0.174 10 87 4.894,4.291 5.094,4.449 0.200,0.158 10 88 2.634,1.311 2.767,1.518 0.133,0.207 10 1 2.634,0.769 2.767,0.976 0.133,0.207 10 3 2.634,1.848 2.767,2.055 0.133,0.207 10 2 2.629,3.744 2.762,3.951 0.133,0.207 10 1 2.629,3.202 2.762,3.409 0.133,0.207 10 3 2.629,4.281 2.762,4.488 0.133,0.207 10 2 2.335,0.797 2.565,0.962 0.230,0.165 10 VC 2.204,1.315 2.619,1.480 0.415,0.165 10 VVL+ 2.204,1.875 2.619,2.040 0.415,0.165 10 VVL- 2.209,3.753 2.624,3.918 0.415,0.165 10 VVR+ 2.209,4.313 2.624,4.478 0.415,0.165 10 VVR- 2.316,3.221 2.546,3.386 0.230,0.165 10 VC 3.797,5.033 4.543,5.219 0.746,0.186 10 *1: for RHD 3.797,5.285 4.543,5.471 0.746,0.186 10 *2: for LHD

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
U163269E01
0.194,0.212 0.412,0.452 0.217,0.239 10 *a 0.266,1.526 0.619,1.727 0.353,0.201 10 C26 0.266,1.919 0.630,2.120 0.364,0.201 10 C25 0.72,1.524 0.887,1.725 0.167,0.201 10 *b 0.72,1.912 0.887,2.113 0.167,0.201 10 *c 2.811,2.499 3.032,2.650 0.221,0.151 10 VC 2.01,2.216 2.765,2.555 false

a.

Disconnect the VVT sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C26-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.0 V
C25-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.0 V


Text in Illustration
*a Front view of wire harness connector
(to VVT Sensor)
*b Bank 1
*c Bank 2



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C26-1 (VVL+) - C46-92 (VV1+) Always Below 1 Ω
C26-2 (VVL-) - C46-91 (VV1-) Always Below 1 Ω
C25-1 (VVR+) - C46-87 (VV2+) Always Below 1 Ω
C25-2 (VVR-) - C46-88 (VV2-) Always Below 1 Ω
C26-1 (VVL+) or C46-92 (VV1+) - Body ground Always 10 kΩ or higher
C26-2 (VVL-) or C46-91 (VV1-) - Body ground Always 10 kΩ or higher
C25-1 (VVR+) or C46-87 (VV2+) - Body ground Always 10 kΩ or higher
C25-2 (VVR-) or C46-88 (VV2-) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C26-1 (VVL+) - C45-92 (VV1+) Always Below 1 Ω
C26-2 (VVL-) - C45-91 (VV1-) Always Below 1 Ω
C25-1 (VVR+) - C45-87 (VV2+) Always Below 1 Ω
C25-2 (VVR-) - C45-88 (VV2-) Always Below 1 Ω
C26-1 (VVL+) or C45-92 (VV1+) - Body ground Always 10 kΩ or higher
C26-2 (VVL-) or C45-91 (VV1-) - Body ground Always 10 kΩ or higher
C25-1 (VVR+) or C45-87 (VV2+) - Body ground Always 10 kΩ or higher
C25-2 (VVR-) or C45-88 (VV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT)
a.
B449531E01
0.458,1.76 0.771,1.958 0.313,0.198 10 false OK 1.625,1.552 2.417,1.781 0.792,0.229 10 false Clearance 2.635,1.844 2.958,2.083 0.323,0.24 10 false NG

Check the VVT sensor installation.

OK:

Sensor is installed correctly.




OK

4.INSPECT INTAKE CAMSHAFT (TEETH)

NG

4.INSPECT INTAKE CAMSHAFT (TEETH)
a.

Check the teeth of the camshaft.

OK:

Teeth do not have any cracks or deformation.




OK

5.REPLACE VVT SENSOR

NG

5.REPLACE VVT SENSOR

NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear DTCs.


e.

Start the engine and idle it for 10 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read DTCs.

Result
Result Proceed to
No DTC is output A
P0340, P0342, P0343, P0345, P0347 or P0348 is output B

HINT:

If the engine does not start, replace the ECM.




A

END

B