Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM U

1UR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


CHECK ECM


U163201E02
5.313,0.719 5.604,0.875 0.292,0.156 10 false A52 2.24,0.708 2.531,0.865 0.292,0.156 10 false C46 5.917,0.719 6.208,0.875 0.292,0.156 10 false A38 2.833,0.719 3.125,0.875 0.292,0.156 10 false C45 5.594,0.5 5.76,0.646 0.167,0.146 10 false *1 6.229,0.5 6.406,0.656 0.177,0.156 10 false *2 2.531,0.5 2.698,0.646 0.167,0.146 10 false *1 3.125,0.5 3.302,0.656 0.177,0.156 10 false *2 0.531,2.906 1.438,3.115 0.906,0.208 10 false *1: for RHD 0.531,3.188 1.438,3.396 0.906,0.208 10 false *2: for LHD

a.

Measure the voltage according to the value(s) in the table below.

HINT:

The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A52*1-1 (BATT) - C46*1-81 (E1)
A38*2-1 (BATT) - C45*2-81 (E1)
L - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
C46*1-41 (+BM) - C46*1-81 (E1)
C45*2-41 (+BM) - C45*2-81 (E1)
P - BR Power source of throttle actuator Always 11 to 14 V
A52*1-28 (IGSW) - C46*1-81 (E1)
A38*2-28 (IGSW) - C45*2-81 (E1)
B - BR Engine switch Engine switch on (IG) 11 to 14 V
A52*1-3 (+B) - C46*1-81 (E1)
A38*2-3 (+B) - C45*2-81 (E1)
B - BR Power source of ECM Engine switch on (IG) 11 to 14 V
A52*1-2 (+B2) - C46*1-81 (E1)
A38*2-2 (+B2) - C45*2-81 (E1)
B - BR Power source of ECM Engine switch on (IG) 11 to 14 V
C46*1-58 (OC1+) - C46*1-57 (OC1-)
C45*2-58 (OC1+) - C45*2-57 (OC1-)
B - L Camshaft timing oil control valve (OCV) (for Intake Side of Bank 1) Idling Pulse generation
(see waveform 1)
C46*1-52 (OC2+) - C46*1-51 (OC2-)
C45*2-52 (OC2+) - C45*2-51 (OC2-)
L - R Camshaft timing oil control valve (OCV) (for Intake Side of Bank 2) Idling Pulse generation
(see waveform 1)
C46*1-56 (OE1+) - C46*1-55 (OE1-)
C45*2-56 (OE1+) - C45*2-55 (OE1-)
W - B Camshaft timing oil control valve (OCV) (for Exhaust Side of Bank 1) Idling Pulse generation
(see waveform 1)
C46*1-50 (OE2+) - C46*1-49 (OE2-)
C45*2-50 (OE2+) - C45*2-49 (OE2-)
R - B Camshaft timing oil control valve (OCV) (for Exhaust Side of Bank 2) Idling Pulse generation
(see waveform 1)
A52*1-34 (MREL) - C46*1-81 (E1)
A38*2-34 (MREL) - C45*2-81 (E1)
V - BR EFI MAIN NO. 1 relay Engine switch on (IG) 11 to 14 V
C46*1-74 (VG) - C46*1-75 (E2G)
C45*2-74 (VG) - C45*2-75 (E2G)
Y - W Mass air flow meter Idling, Shift lever position P or N, A/C switch OFF 0.5 to 3.0 V
C46*1-73 (THA) - C46*1-98 (E2)
C45*2-73 (THA) - C45*2-98 (E2)
B - BR Intake air temperature sensor Idling, Intake air temperature 20°C (68°F) 0.5 to 3.4 V
C46*1-76 (THW) - C46*1-98 (E2)
C45*2-76 (THW) - C45*2-98 (E2)
B - BR Engine coolant temperature sensor Idling, Engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
C46*1-80 (VCTA) - C46*1-79 (ETA)
C45*2-80 (VCTA) - C45*2-79 (ETA)
Y - L Power source of throttle position sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C46*1-78 (VTA1) - C46*1-79 (ETA)
C45*2-78 (VTA1) - C45*2-79 (ETA)
Y - L Throttle position sensor (for engine control) Engine switch on (IG),
Throttle valve fully closed
0.5 to 1.2 V
Engine switch on (IG),
Throttle valve fully open
3.2 to 4.8 V
C46*1-77 (VTA2) - C46*1-79 (ETA)
C45*2-77 (VTA2) - C45*2-79 (ETA)
B - L Throttle position sensor (for sensor malfunction detection) Engine switch on (IG),
Throttle valve fully closed
2.1 to 3.1 V
Engine switch on (IG),
Throttle valve fully open
4.5 to 5.5 V
A52*1-55 (VPA) - A52*1-58 (EPA)
A38*2-55 (VPA) - A38*2-58 (EPA)
R - W Accelerator pedal position sensor (for engine control) Engine switch on (IG),
Accelerator pedal released
0.5 to 1.1 V
Engine switch on (IG),
Accelerator pedal fully depressed
2.6 to 4.5 V
A52*1-56 (VPA2) - A52*1-60 (EPA2)
A38*2-56 (VPA2) - A38*2-60 (EPA2)
GR - BE Accelerator pedal position sensor (for sensor malfunctioning detection) Engine switch on (IG),
Accelerator pedal released
1.2 to 2.0 V
Engine switch on (IG),
Accelerator pedal fully depressed
3.4 to 4.75 V
A52*1-57 (VCPA) - A52*1-58 (EPA)
A38*2-57 (VCPA) - A38*2-58 (EPA)
L - W Power source of accelerator pedal position sensor (for VPA) Engine switch on (IG) 4.5 to 5.5 V
A52*1-59 (VCP2) - A52*1-60 (EPA2)
A38*2-59 (VCP2) - A38*2-60 (EPA2)
V - BE Power source of accelerator pedal position sensor (for VPA2) Engine switch on (IG) 4.5 to 5.5 V
C46*1-22 (HA1A) - C46*1-23 (E04)
C45*2-22 (HA1A) - C45*2-23 (E04)
L - W-B A/F sensor heater Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
C46*1-20 (HA2A) - C46*1-21 (E05)
C45*2-20 (HA2A) - C45*2-21 (E05)
G - W-B A/F sensor heater Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
C46*1-126 (A1A+) - C46*1-81 (E1)
C45*2-126 (A1A+) - C45*2-81 (E1)
G -BR A/F sensor Engine switch on (IG) 3.3 V*3
C46*1-125 (A1A-) - C46*1-81 (E1)
C45*2-125 (A1A-) - C45*2-81 (E1)
R - BR A/F sensor Engine switch on (IG) 2.9 V*3
C46*1-103 (A2A+) - C46*1-81 (E1)
C45*2-103 (A2A+) - C45*2-81 (E1)
P - BR A/F sensor Engine switch on (IG) 3.3 V*3
C46*1-102 (A2A-) - C46*1-81 (E1)
C45*2-102 (A2A-) - C45*2-81 (E1)
L - BR A/F sensor Engine switch on (IG) 2.9 V*3
C46*1-45 (HT1B) - C46*1-46 (E03)
C45*2-45 (HT1B) - C45*2-46 (E03)
G - W-B Heated oxygen sensor heater Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
C46*1-44 (HT2B) - C46*1-46 (E03)
C45*2-44 (HT2B) - C45*2-46 (E03)
B - W-B Heated oxygen sensor heater Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
C46*1-114 (OX1B) - C46*1-115 (EX1B)
C45*2-114 (OX1B) - C45*2-115 (EX1B)
G - L Heated oxygen sensor Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation
(see waveform 2)
C46*1-112 (OX2B) - C46*1-113 (EX2B)
C45*2-112 (OX2B) - C45*2-113 (EX2B)
R - W Heated oxygen sensor Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation
(see waveform 2)
C46*1-86 (#10) - C46*1-43 (E01)
C45*2-86 (#10) - C45*2-43 (E01)
R - W-B Injector Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 3)
C46*1-109 (#20) - C46*1-43 (E01)
C45*2-109 (#20) - C45*2-43 (E01)
L - W-B Injector Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 3)
C46*1-85 (#30) - C46*1-43 (E01)
C45*2-85 (#30) - C45*2-43 (E01)
R - W-B Injector Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 3)
C46*1-108 (#40) - C46*1-43 (E01)
C45*2-108 (#40) - C45*2-43 (E01)
Y - W-B Injector Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 3)
C46*1-84 (#50) - C46*1-43 (E01)
C45*2-84 (#50) - C45*2-43 (E01)
G - W-B Injector Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 3)
C46*1-107 (#60) - C46*1-43 (E01)
C45*2-107 (#60) - C45*2-43 (E01)
R - W-B Injector Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 3)
C46*1-83 (#70) - C46*1-43 (E01)
C45*2-83 (#70) - C45*2-43 (E01)
W - W-B Injector Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 3)
C46*1-106 (#80) - C46*1-43 (E01)
C45*2-106 (#80) - C45*2-43 (E01)
R - W-B Injector Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 3)
C46*1-94 (KNK1) - C46*1-93 (EKNK)
C45*2-94 (KNK1) - C45*2-93 (EKNK)
R - G Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 4)
C46*1-117 (KNK2) - C46*1-116 (EKN2)
C45*2-117 (KNK2) - C45*2-116 (EKN2)
W - B Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 4)
C46*1-96 (KNK3) - C46*1-95 (EKN3)
C45*2-96 (KNK3) - C45*2-95 (EKN3)
W - B Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 4)
C46*1-119 (KNK4) - C46*1-118 (EKN4)
C45*2-119 (KNK4) - C45*2-118 (EKN4)
R - G Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 4)
C46*1-92 (VV1+) - C46*1-91 (VV1-)
C45*2-92 (VV1+) - C45*2-91 (VV1-)
R - Y Variable valve timing (VVT) sensor (for Intake Side of Bank 1) Idling Pulse generation
(see waveform 5)
C46*1-87 (VV2+) - C46*1-88 (VV2-)
C45*2-87 (VV2+) - C45*2-88 (VV2-)
R - Y Variable valve timing (VVT) sensor (for Intake Side for Bank 2) Idling Pulse generation
(see waveform 5)
C46*1-69 (EV1+) - C46*1-68 (EV1-)
C45*2-69 (EV1+) - C45*2-68 (EV1-)
L - Y Variable valve timing (VVT) sensor (for Exhaust Side of Bank 1) Idling Pulse generation
(see waveform 16)
C46*1-64 (EV2+) - C46*1-65 (EV2-)
C45*2-64 (EV2+) - C45*2-65 (EV2-)
L - Y Variable valve timing (VVT) sensor (for Exhaust Side of Bank 2) Idling Pulse generation
(see waveform 16)
C46*1-110 (NE+) - C46*1-111 (NE-)
C45*2-110 (NE+) - C45*2-111 (NE-)
W - Y Crankshaft position sensor Idling Pulse generation
(see waveform 5)
C46*1-40 (IGT1) - C46*1-81 (E1)
C45*2-40 (IGT1) - C45*2-81 (E1)
Y - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
C46*1-33 (IGT2) - C46*1-81 (E1)
C45*2-33 (IGT2) - C45*2-81 (E1)
L - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
C46*1-37 (IGT3) - C46*1-81 (E1)
C45*2-37 (IGT3) - C45*2-81 (E1)
B - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
C46*1-34 (IGT4) - C46*1-81 (E1)
C45*2-34 (IGT4) - C45*2-81 (E1)
L - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
C46*1-35 (IGT5) - C46*1-81 (E1)
C45*2-35 (IGT5) - C45*2-81 (E1)
G - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
C46*1-36 (IGT6) - C46*1-81 (E1)
C45*2-36 (IGT6) - C45*2-81 (E1)
P - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
C46*1-38 (IGT7) - C46*1-81 (E1)
C45*2-38 (IGT7) - C45*2-81 (E1)
W - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
C46*1-39 (IGT8) - C46*1-81 (E1)
C45*2-39 (IGT8) - C45*2-81 (E1)
G - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
C46*1-105 (IGF1) - C46*1-81 (E1)
C45*2-105 (IGF1) - C45*2-81 (E1)
G - BR Ignition coil (ignition confirmation signal) Engine switch on (IG) 4.5 to 5.5 V
Idling Pulse generation
(see waveform 6)
C46*1-104 (IGF2) - C46*1-81 (E1)
C45*2-104 (IGF2) - C45*2-81 (E1)
R - BR Ignition coil (ignition confirmation signal) Engine switch on (IG) 4.5 to 5.5 V
Idling Pulse generation
(see waveform 6)
C46*1-63 (PRG) - C46*1-81 (E1)
C45*2-63 (PRG) - C45*2-81 (E1)
B - BR Purge VSV Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(see waveform 7)
A52*1-13 (SPD) - C46*1-81 (E1)
A38*2-13 (SPD) - C45*2-81 (E1)
L - BR Speed signal from combination meter Driving at 20 km/h (12 mph) Pulse generation
(see waveform 8)
A52*1-46 (STA) - C46*1-81 (E1)
A38*2-46 (STA) - C45*2-81 (E1)
R - BR Starter signal Cranking 5.5 V or more
C46*1-120 (NSW) - C46*1-81 (E1)
C45*2-120 (NSW) - C45*2-81 (E1)
L - BR Park / neutral position switch Engine switch on (IG), Shift lever position other than P and N 11 to 14 V
Engine switch on (IG), Shift lever position in P or N Below 3.0 V
A52*1-36 (STP) - C46*1-81 (E1)
A38*2-36 (STP) - C45*2-81 (E1)
R - BR Stop light switch Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
A52*1-35 (ST1-) - C46*1-81 (E1)
A38*2-35 (ST1-) - C45*2-81 (E1)
P - BR Stop light switch
(opposite to STP terminal)
Engine switch on (IG),
Brake pedal depressed
Below 1.5 V
Engine switch on (IG),
Brake pedal released
7.5 to 14 V
C46*1-19 (M+) - C46*1-82 (ME01)
C45*2-19 (M+) - C45*2-82 (ME01)
R - W-B Throttle actuator Idling with warm engine Pulse generation
(see waveform 9)
C46*1-18 (M-) - C46*1-82 (ME01)
C45*2-18 (M-) - C45*2-82 (ME01)
G - W-B Throttle actuator Idling with warm engine Pulse generation
(see waveform 10)
A52*1-52 (FPC) - C46*1-81 (E1)
A38*2-52 (FPC) - C45*2-81 (E1)
W - BR Fuel pump control Engine switch on (IG) Below 1.5 V
A52*1-16 (TC) - C46*1-81 (E1)
A38*2-16 (TC) - C45*2-81 (E1)
V - BR Terminal TC of DLC3 Engine switch on (IG) 11 to 14 V
A52*1-15 (TACH) - C46*1-81 (E1)
A38*2-15 (TACH) - C45*2-81 (E1)
W - BR Engine speed Idling Pulse generation
(see waveform 11)
C46*1-67 (VCV1) - C46*1-98 (E2)
C45*2-67 (VCV1) - C45*2-98 (E2)
L - BR Power source for sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C46*1-66 (VCV2) - C46*1-98 (E2)
C45*2-66 (VCV2) - C45*2-98 (E2)
L - BR Power source for sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C46*1-32 (ALT) - C46*1-81 (E1)
C45*2-32 (ALT) - C45*2-81 (E1)
R - BR Generator Engine switch on (IG) 11 to 14 V
A52*1-10 (CANH) - C46*1-81 (E1)
A38*2-10 (CANH) - C45*2-81 (E1)
V - BR CAN communication line Engine switch on (IG) Pulse generation
(see waveform 12)
A52*1-11 (CANL) - C46*1-81 (E1)
A38*2-11 (CANL) - C45*2-81 (E1)
W - BR CAN communication line Engine switch on (IG) Pulse generation
(see waveform 13)
C46*1-62 (ACIS) - C46*1-81 (E1)
C45*2-62 (ACIS) - C45*2-81 (E1)
L - BR VSV for ACIS (Acoustic Control Induction System) operation signal Engine switch on (IG) 11 to 14 V
C46*1-28 (AIRV) - C46*1-81 (E1)
C45*2-28 (AIRV) - C45*2-81 (E1)
BR - BR Air switching valve signal for secondary air injection system Engine switch on (IG) 11 to 14 V
C46*1-54 (AIRP) - C46*1-81 (E1)
C45*2-54 (AIRP) - C45*2-81 (E1)
P - BR Air pump control signal for secondary air injection system Engine switch on (IG) 11 to 14 V
C46*1-30 (AIDI) - C46*1-81 (E1)
C45*2-30 (AIDI) - C45*2-81 (E1)
G - BR Diagnostic information signal for secondary air injection system Air injection system operates Pulse generation
(see waveform 15)
A52*1-54 (AIP) - C46*1-98 (E2)
A38*2-54 (AIP) - C45*2-98 (E2)
P - BR Secondary air injection system pressure signal Engine switch on (IG) 3.0 to 3.6 V
A52*1-53 (AIP2) - C46*1-98 (E2)
A38*2-53 (AIP2) - C45*2-98 (E2)
L - BR Secondary air injection system pressure signal Engine switch on (IG) 3.0 to 3.6 V
C46*1-60 (HAI1) - C46*1-81 (E1)
C45*2-60 (HAI1) - C45*2-81 (E1)
G - BR Air pump heater for secondary air injection system AI heater operating Below 1.5 V
C46*1-61 (AIR1) - C46*1-81 (E1)
C45*2-61 (AIR1) - C45*2-81 (E1)
R - BR Air pump for secondary air injection system AI operating 11 to 14 V
C46*1-90 (G2) - C46*1- 89 (G2-)
C45*2-90 (G2) - C45*2- 89 (G2-)
G - Y Camshaft position sensor Idling Pulse generation
(see waveform 14)
C46*1-72 (PSP) - C46*1-98 (E2)
C45*2-72 (PSP) - C45*2-98 (E2)
G - BR Power steering oil pressure switch Engine switch on (IG) 0.5 to 4.5 V
C46*1-97 (PIM) - C46*1-98 (E2)
C45*2-97 (PIM) - C45*2-98 (E2)
L - BR Manifold absolute pressure sensor Idling 1.2 to 2.0 V
A52*1-17 (ACT) - C46*1-81 (E1)
A38*2-17 (ACT) - C45*2-81 (E1)
G - BR A/C signal A/C on 11 to 14 V
A/C off Below 1.5 V
A52*1-19 (AC1) - C46*1-81 (E1)
A38*2-19 (AC1) - C45*2-81 (E1)
L - BR A/C signal A/C on Below 1.5 V
A/C off 11 to 14 V
A52*1-7 (NEO) - C46*1-81 (E1)
A38*2-7 (NEO) - C45*2-81 (E1)
L - BR Engine speed signal Idle after engine warmed up Pulse generation
(see waveform 17)

HINT:
·

*1: for RHD

·

*2: for LHD

·

*3: The ECM terminal voltage is constant regardless of the output voltage from the sensor.




b.
U115314E04
0.448,0.167 1.135,0.365 0.688,0.198 10 false 5 V/DIV. 0.5,1.073 0.938,1.271 0.438,0.198 10 false GND 1.479,1.917 2.375,2.115 0.896,0.198 10 false 1 msec./DIV.

WAVEFORM 1:

Camshaft timing oil control valve (OCV)
Terminal No. (Symbols) Tool Setting Condition
C46*1-58 (OC1+) - C46*1-57 (OC1-)
C45*2-58 (OC1+) - C45*2-57 (OC1-)
5 V/DIV., 1 msec./DIV. Idling
C46*1-52 (OC2+) - C46*1-51 (OC2-)
C45*2-52 (OC2+) - C45*2-51 (OC2-)
5 V/DIV., 1 msec./DIV. Idling
C46*1-56 (OE1+) - C46*1-55 (OE1-)
C45*2-56 (OE1+) - C45*2-55 (OE1-)
5 V/DIV., 1 msec./DIV. Idling
C46*1-50 (OE2+) - C46*1-49 (OE2-)
C45*2-50 (OE2+) - C45*2-49 (OE2-)
5 V/DIV., 1 msec./DIV. Idling

*1: for RHD

*2: for LHD


c.
U115312E03
0.313,0.146 1.031,0.365 0.719,0.219 10 false 0.2 V/DIV. 0.438,1.417 0.823,1.615 0.385,0.198 10 false GND 1.656,1.854 2.656,2.052 1,0.198 10 false 200 msec./DIV.

WAVEFORM 2:

Heated oxygen sensor
Terminal No. (Symbols) Tool Setting Condition
C46*1-114 (OX1B) - C46*1-115 (EX1B)
C45*2-114 (OX1B) - C45*2-115 (EX1B)
0.2 V/DIV., 200 msec./DIV. Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
C46*1-112 (OX2B) - C46*1-113 (EX2B)
C45*2-112 (OX2B) - C45*2-113 (EX2B)
0.2 V/DIV., 200 msec./DIV. Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

*1: for RHD

*2: for LHD

HINT:

In DATA LIST, item O2S B1S2 or O2S B2S2 shows the ECM input values from the heated oxygen sensor.



d.
A369420E01
0.5,0.135 1.208,0.344 0.708,0.208 10 false 20 V/DIV. 0.604,1.542 0.979,1.74 0.375,0.198 10 false GND 1.792,1.875 2.885,2.063 1.094,0.188 10 false 20 msec./DIV.

WAVEFORM 3:

Injector No. 1 (to No. 8) injection signal
Terminal No. (Symbols) Tool Setting Condition
C46*1-86 (#10) - C46*1-43 (E01)
C45*2-86 (#10) - C45*2-43 (E01)
20 V/DIV., 20 msec./DIV. Idling
C46*1-109 (#20) - C46*1-43 (E01)
C45*2-109 (#20) - C45*2-43 (E01)
20 V/DIV., 20 msec./DIV. Idling
C46*1-85 (#30) - C46*1-43 (E01)
C45*2-85 (#30) - C45*2-43 (E01)
20 V/DIV., 20 msec./DIV. Idling
C46*1-108 (#40) - C46*1-43 (E01)
C45*2-108 (#40) - C45*2-43 (E01)
20 V/DIV., 20 msec./DIV. Idling
C46*1-84 (#50) - C46*1-43 (E01)
C45*2-84 (#50) - C45*2-43 (E01)
20 V/DIV., 20 msec./DIV. Idling
C46*1-107 (#60) - C46*1-43 (E01)
C45*2-107 (#60) - C45*2-43 (E01)
20 V/DIV., 20 msec./DIV. Idling
C46*1-83 (#70) - C46*1-43 (E01)
C45*2-83 (#70) - C45*2-43 (E01)
20 V/DIV., 20 msec./DIV. Idling
C46*1-106 (#80) - C46*1-43 (E01)
C45*2-106 (#80) - C45*2-43 (E01)
20 V/DIV., 20 msec./DIV. Idling

*1: for RHD

*2: for LHD

HINT:

The wavelength becomes shorter as the engine rpm increases.



e.
A357198E02
2.406,0.531 3.052,0.708 0.646,0.177 10 false 1 V/DIV. 1.135,1.896 2.063,2.094 0.927,0.198 10 false 1 msec./DIV. 2.615,0.99 3.063,1.198 0.448,0.208 10 false GND

WAVEFORM 4:

Knock sensor
Terminal No. (Symbols) Tool Setting Condition
C46*1-94 (KNK1) - C46*1-93 (EKNK)
C45*2-94 (KNK1) - C45*2-93 (EKNK)
1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine
C46*1-117 (KNK2) - C46*1-116 (EKN2)
C45*2-117 (KNK2) - C45*2-116 (EKN2)
1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine
C46*1-96 (KNK3) - C46*1-95 (EKN3)
C45*2-96 (KNK3) - C45*2-95 (EKN3)
1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine
C46*1-119 (KNK4) - C46*1-118 (EKN4)
C45*2-119 (KNK4) - C45*2-118 (EKN4)
1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine

*1: for RHD

*2: for LHD

HINT:
·

The wavelength becomes shorter as the engine rpm increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




f.
A217926E01
0.24,1.161 0.470,1.326 0.230,0.165 10 (a) 0.24,1.707 0.455,1.859 0.215,0.151 10 (b) 0.24,2.075 0.479,2.280 0.239,0.206 10 (c) 2.819,1.267 3.155,1.416 0.336,0.149 10 GND 2.819,2.197 3.155,2.346 0.336,0.149 10 GND 2.819,1.815 3.155,1.964 0.336,0.149 10 GND 1.112,2.501 2.032,2.642 0.921,0.141 10 20 msec./DIV. 2.701,0.773 3.265,0.929 0.563,0.156 10 5 V/DIV.

WAVEFORM 5:

Crankshaft position sensor and VVT sensor for intake side
Terminal No. (Symbols) Tool Setting Condition
(a) C46*1-110 (NE+) - C46*1-111 (NE-)
(a) C45*2-110 (NE+) - C45*2-111 (NE-)
5 V/DIV., 20 msec./DIV. Idle after engine warmed up
(b) C46*1-92 (VV1+) - C46*1-91 (VV1-)
(b) C45*2-92 (VV1+) - C45*2-91 (VV1-)
5 V/DIV., 20 msec./DIV. Idle after engine warmed up
(c) C46*1-87 (VV2+) - C46*1-88 (VV2-)
(c) C45*2-87 (VV2+) - C45*2-88 (VV2-)
5 V/DIV., 20 msec./DIV. Idle after engine warmed up

*1: for RHD

*2: for LHD

HINT:

The wavelength becomes shorter as engine rpm increases.



g.
A384959E01
0.521,0.104 1.125,0.333 0.604,0.229 10 false 2 V/DIV. 0.917,0.667 1.135,0.865 0.219,0.198 10 false (a) 0.479,0.885 0.979,1.104 0.5,0.219 10 false Ground 0.479,1.448 0.979,1.646 0.5,0.198 10 false Ground 0.927,1.229 1.135,1.438 0.208,0.208 10 false (b) 1.771,1.844 3.031,2.052 1.26,0.208 10 false 20 msec./DIV.

WAVEFORM 6:

Igniter IGT signal (from ECM to igniter) and Igniter IGF signal (from igniter to ECM)
Terminal No. (Symbols) Tool Setting Condition
(a) C46*1-40 (IGT1) - C46*1-81 (E1)
(a) C45*2-40 (IGT1) - C45*2-81 (E1)
2 V/DIV., 20 msec./DIV. Idling
(a) C46*1-33 (IGT2) - C46*1-81 (E1)
(a) C45*2-33 (IGT2) - C45*2-81 (E1)
2 V/DIV., 20 msec./DIV. Idling
(a) C46*1-37 (IGT3) - C46*1-81 (E1)
(a) C45*2-37 (IGT3) - C45*2-81 (E1)
2 V/DIV., 20 msec./DIV. Idling
(a) C46*1-34 (IGT4) - C46*1-81 (E1)
(a) C45*2-34 (IGT4) - C45*2-81 (E1)
2 V/DIV., 20 msec./DIV. Idling
(a) C46*1-35 (IGT5) - C46*1-81 (E1)
(a) C45*2-35 (IGT5) - C45*2-81 (E1)
2 V/DIV., 20 msec./DIV. Idling
(a) C46*1-36 (IGT6) - C46*1-81 (E1)
(a) C45*2-36 (IGT6) - C45*2-81 (E1)
2 V/DIV., 20 msec./DIV. Idling
(a) C46*1-38 (IGT7) - C46*1-81 (E1)
(a) C45*2-38 (IGT7) - C45*2-81 (E1)
2 V/DIV., 20 msec./DIV. Idling
(a) C46*1-39 (IGT8) - C46*1-81 (E1)
(a) C45*2-39 (IGT8) - C45*2-81 (E1)
2 V/DIV., 20 msec./DIV. Idling
(b) C46*1-105 (IGF1) - C46*1-81 (E1)
(b) C45*2-105 (IGF1) - C45*2-81 (E1)
2 V/DIV., 20 msec./DIV. Idling
(b) C46*1-104 (IGF2) - C46*1-81 (E1)
(b) C45*2-104 (IGF2) - C45*2-81 (E1)
2 V/DIV., 20 msec./DIV. Idling

*1: for RHD

*2: for LHD

HINT:

The wavelength becomes shorter as engine rpm increases.



h.
A218020E03
2.676,0.174 3.296,0.318 0.620,0.144 10 10 V/DIV. 2.806,0.925 3.143,1.065 0.336,0.140 10 GND 1.189,1.789 1.937,1.935 0.748,0.147 10 20 ms./DIV.

WAVEFORM 7:

Purge VSV
Terminal No. (Symbols) Tool Setting Condition
C46*1-63 (PRG) - C46*1-81 (E1)
C45*2-63 (PRG) - C45*2-81 (E1)
10 V/DIV., 10 to 100 msec./DIV. Idling

*1: for RHD

*2: for LHD

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



i.
U115313E04
0.396,0.229 1.083,0.427 0.688,0.198 10 false 2 V/DIV. 0.469,1.125 0.865,1.323 0.396,0.198 10 false GND 1.531,1.854 2.49,2.052 0.958,0.198 10 false 20 msec./DIV.

WAVEFORM 8:

Vehicle speed signal
Terminal No. (Symbols) Tool Setting Condition
A52*1-13 (SPD) - C46*1-81 (E1)
A38*2-13 (SPD) - C45*2-81 (E1)
2 V/DIV., 20 msec./DIV. Driving at 20 km/h (12 mph)

*1: for RHD

*2: for LHD

HINT:

The wavelength becomes shorter as the vehicle speed increases.



j.
A208000E06
2.856,0.973 3.186,1.119 0.330,0.146 10 GND 2.631,0.216 3.176,0.360 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.237,1.806 2.058,1.964 0.820,0.158 10 1 msec./DIV.

WAVEFORM 9:

Throttle actuator positive terminal
Terminal No. (Symbols) Tool Setting Condition
C46*1-19 (M+) - C46*1-82 (ME01)
C45*2-19 (M+) - C45*2-82 (ME01)
5 V/DIV., 1 msec./DIV. Idling with warm engine

*1: for RHD

*2: for LHD

HINT:

The duty ratio varies depending on the throttle actuator operation.



k.
A245848E04
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.246,1.82 2.076,1.967 0.83,0.147 10 1 msec./DIV.

WAVEFORM 10:

Throttle actuator negative terminal
Terminal No. (Symbols) Tool Setting Condition
C46*1-18 (M-) - C46*1-82 (ME01)
C45*2-18 (M-) - C45*2-82 (ME01)
5 V/DIV., 1 msec./DIV. Idling with warm engine

*1: for RHD

*2: for LHD

HINT:

The duty ratio varies depending on the throttle actuator operation.



l.
A381414E01
0.594,0.625 1.24,0.813 0.646,0.188 10 false 5 V/DIV. 0.615,2.042 1,2.229 0.385,0.188 10 false GND 1.688,2.667 2.708,2.854 1.021,0.188 10 false 10 msec./DIV.

WAVEFORM 11:

Engine speed signal
Terminal No. (Symbols) Tool Setting Condition
A52*1-15 (TACH) - C46*1-81 (E1)
A38*2-15 (TACH) - C45*2-81 (E1)
5 V/DIV., 10 msec./DIV. Idling

*1: for RHD

*2: for LHD

HINT:

The wavelength becomes shorter as the engine rpm increases.



m.
A357201E02
2.979,1.396 3.385,1.594 0.406,0.198 10 false GND 2.76,0.292 3.323,0.479 0.563,0.188 10 false 1 V/DIV. 1.469,1.896 2.469,2.083 1,0.188 10 false 10 μsec./DIV.

WAVEFORM 12:

CAN communication signal
Terminal No. (Symbols) Tool Setting Condition
A52*1-10 (CANH) - C46*1-81 (E1)
A38*2-10 (CANH) - C45*2-81 (E1)
1 V/DIV., 10 μsec./DIV. Engine stops and engine switch on (IG)

*1: for RHD

*2: for LHD

HINT:

The waveform varies depending on the CAN communication signal.



n.
A357202E02
3.01,1.354 3.385,1.531 0.375,0.177 10 false GND 2.771,0.229 3.385,0.417 0.615,0.188 10 false 1 V/DIV. 1.448,1.865 2.354,2.063 0.906,0.198 10 false 10 μsec./DIV.

WAVEFORM 13:

CAN communication signal
Terminal No. (Symbols) Tool Setting Condition
A52*1-11 (CANL) - C46*1-81 (E1)
A38*2-11 (CANL) - C45*2-81 (E1)
1 V/DIV., 10 μsec./DIV. Engine stops and engine switch on (IG)

*1: for RHD

*2: for LHD

HINT:

The waveform varies depending on the CAN communication signal.



o.
A211721E01
2.827,1.417 3.206,1.598 0.379,0.181 10 GND 2.827,1.965 3.206,2.145 0.379,0.180 10 GND 0.146,1.87 0.458,2.033 0.312,0.163 10 CH2 0.146,1.321 0.456,1.484 0.310,0.163 10 CH1 1.123,2.469 2.063,2.645 0.941,0.177 10 20 msec./DIV. 2.696,0.738 3.261,0.914 0.566,0.177 10 5 V/DIV.

WAVEFORM 14:

Crankshaft position sensor and camshaft position sensor
Terminal No. (Symbols) Tool Setting Condition
CH1: C46*1-110 (NE+) - C46*1-111 (NE-)
CH1: C45*2-110 (NE+) - C45*2-111 (NE-)
5 V/DIV., 20 msec./DIV. Idle after engine warmed up
CH2: C46*1-90 (G2) - C46*1-89 (G2-)
CH2: C45*2-90 (G2) - C45*2-89 (G2-)
5 V/DIV., 20 msec./DIV. Idle after engine warmed up

*1: for RHD

*2: for LHD

HINT:

The wavelength becomes shorter as the engine rpm increases.



p.
A100214E06
2.687,0.001 3.291,0.182 0.604,0.180 10 5 V/DIV. 1.063,1.87 1.976,2.051 0.913,0.180 10 50 msec./DIV.

WAVEFORM 15:

Terminal DI of air injection control driver
Terminal No. (Symbols) Tool Setting Condition
C46*1-30 (AIDI) - C46*1-81 (E1)
C45*2-30 (AIDI) - C45*2-81 (E1)
5 V/DIV., 50 msec./DIV. Performing system check using GTS (air injection check)

*1: for RHD

*2: for LHD

HINT:

The wavelength changes when the air injection control driver detects malfunctions in the air injection system (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0412).



q.
A217927E01
0.263,1.166 0.493,1.331 0.230,0.165 10 (a) 0.263,1.711 0.459,1.894 0.196,0.183 10 (b) 0.263,2.083 0.473,2.252 0.210,0.169 10 (c) 2.827,1.272 3.164,1.421 0.336,0.149 10 GND 2.827,2.197 3.164,2.346 0.336,0.149 10 GND 2.827,1.824 3.164,1.973 0.336,0.149 10 GND 1.097,2.511 2.017,2.652 0.921,0.141 10 20 msec./DIV. 2.708,0.79 3.271,0.946 0.563,0.156 10 5 V/DIV.

WAVEFORM 16:

Crankshaft position sensor and VVT sensor for exhaust side
Terminal No. (Symbols) Tool Setting Condition
(a) C46*1-110 (NE+) - C46*1-111 (NE-)
(a) C45*2-110 (NE+) - C45*2-111 (NE-)
5 V/DIV., 20 msec./DIV. Idle after engine warmed up
(b) C46*1-69 (EV1+) - C46*1-68 (EV1-)
(b) C45*2-69 (EV1+) - C45*2-68 (EV1-)
5 V/DIV., 20 msec./DIV. Idle after engine warmed up
(c) C46*1-64 (EV2+) - C46*1-65 (EV2-)
(c) C45*2-64 (EV2+) - C45*2-65 (EV2-)
5 V/DIV., 20 msec./DIV. Idle after engine warmed up

*1: for RHD

*2: for LHD

HINT:

The wavelength becomes shorter as engine rpm increases.



r.
A304647E03
2.573,0.073 3.156,0.292 0.583,0.219 10 false 1 V/DIV. 2.563,1.948 3.323,2.177 0.76,0.229 10 false 2 ms./DIV. 2.802,1.635 3.385,1.854 0.583,0.219 10 false GND

WAVEFORM 17:

Engine speed signal
Terminal No. (Symbols) Tool Setting Condition
A52*1-7 (NEO) - C46*1-81 (E1)
A38*2-7 (NEO) - C45*2-81 (E1)
1 V/DIV., 2 msec./DIV. Idle after engine warmed up

*1: for RHD

*2: for LHD