Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  P032C  Knock Sensor 3 Circuit Low  P032D  Knock Sensor 3 Circuit High  P0332  Knock Sensor 2 Circuit Low Input (Bank 2)  P0333  Knock Sensor 2 Circuit High Input (Bank 2)  P033C  Knock Sensor 4 Circuit Low Input  P033D  Knock Sensor 4 Circuit High Input  


DESCRIPTION

A flat-type knock sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.

Knock sensors are fitted onto the engine block to detect engine knocking.

Each knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. DTC Detection Condition Trouble Area
P0327 Output voltage of the knock sensor (for Bank 1 Sensor 1) is 0.5 V or less (1 trip detection logic).
·

Short in knock sensor (for Bank 1 Sensor 1) circuit


·

Knock sensor (for Bank 1 Sensor 1)


·

ECM


P0328 Output voltage of the knock sensor (for Bank 1 Sensor 1) is 4.5 V or higher (1 trip detection logic).
·

Open in knock sensor (for Bank 1 Sensor 1) circuit


·

Knock sensor (for Bank 1 Sensor 1)


·

ECM


P0332 Output voltage of the knock sensor (for Bank 2 Sensor 1) is 0.5 V or less (1 trip detection logic).
·

Short in knock sensor (for Bank 2 Sensor 1) circuit


·

Knock sensor (for Bank 2 Sensor 1)


·

ECM


P0333 Output voltage of the knock sensor (for Bank 2 Sensor 1) is 4.5 V or higher (1 trip detection logic).
·

Open in knock sensor (for Bank 2 Sensor 1) circuit


·

Knock sensor (for Bank 2 Sensor 1)


·

ECM


P032C Output voltage of the knock sensor (for Bank 1 Sensor 2) is 0.5 V or less (1 trip detection logic).
·

Short in knock sensor (for Bank 1 Sensor 2) circuit


·

Knock sensor (for Bank 1 Sensor 2)


·

ECM


P032D Output voltage of the knock sensor (for Bank 1 Sensor 2) is 4.5 V or higher (1 trip detection logic).
·

Open in knock sensor (for Bank 1 Sensor 2) circuit


·

Knock sensor (for Bank 1 Sensor 2)


·

ECM


P033C Output voltage of the knock sensor (for Bank 2 Sensor 2) is 0.5 V or less (1 trip detection logic).
·

Short in knock sensor (for Bank 2 Sensor 2) circuit


·

Knock sensor (for Bank 2 Sensor 2)


·

ECM


P033D Output voltage of the knock sensor (for Bank 2 Sensor 2) is 4.5 V or higher (1 trip detection logic).
·

Open in knock sensor (for Bank 2 Sensor 2) circuit


·

Knock sensor (for Bank 2 Sensor 2)


·

ECM



HINT:

When DTC P0327, P0328, P0332, P0333, P032C, P032D, P033C or P033D is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. The ECM continues operating in fail-safe mode until the engine switch is turned off.


Reference: Inspection using an oscilloscope

A150243E01
0.336,0.512 1.924,0.727 1.588,0.215 10 KNK1 Signal Waveform 2.632,1.857 2.985,2.060 0.353,0.203 10 GND 2.503,1.065 3.067,1.268 0.564,0.203 10 1 V/DIV. 0.915,2.821 1.757,3.024 0.842,0.203 10 1 msec./DIV.

Standard:
for RHD
Tester Connection Tool Setting Condition Specified Condition
C46-94 (KNK1) - C46-93 (EKNK) 0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Engine speed at 4000 rpm with warm engine The correct waveform is as shown
C46-117 (KNK2) - C46-116 (EKN2) 0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Engine speed at 4000 rpm with warm engine The correct waveform is as shown
C46-96 (KNK3) - C46-95 (EKN3) 0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Engine speed at 4000 rpm with warm engine The correct waveform is as shown
C46-119 (KNK4) - C46-118 (EKN4) 0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Engine speed at 4000 rpm with warm engine The correct waveform is as shown

for LHD
Tester Connection Tool Setting Condition Specified Condition
C45-94 (KNK1) - C45-93 (EKNK) 0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Engine speed at 4000 rpm with warm engine The correct waveform is as shown
C45-117 (KNK2) - C45-116 (EKN2) 0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Engine speed at 4000 rpm with warm engine The correct waveform is as shown
C45-96 (KNK3) - C45-95 (EKN3) 0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Engine speed at 4000 rpm with warm engine The correct waveform is as shown
C45-119 (KNK4) - C45-118 (EKN4) 0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Engine speed at 4000 rpm with warm engine The correct waveform is as shown


MONITOR DESCRIPTION

The knock sensor, located on the cylinder block, detects spark knock. When spark knock occurs, the piezoelectric element of the sensor vibrates. When the ECM detects a voltage in this frequency range, it retards the ignition timing to suppress the spark knock.

The ECM also senses background engine noise with the knock sensor and uses this noise to check for faults in the sensor. If the knock sensor signal level is too low for more than 10 seconds, or if the knock sensor output voltage is outside the normal range, the ECM interprets this as a fault in the knock sensor and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Start the engine and wait 5 minutes.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0327, P0328, P032C, P032D, P0332, P0333, P033C or P033D.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

A278619E04
1.262,0.927 1.370,1.081 0.108,0.155 10 1 2.303,0.927 2.411,1.081 0.108,0.155 10 2 1.18,1.34 1.429,1.489 0.248,0.149 10 U3 1.18,1.483 3.454,1.669 2.274,0.186 10 Knock Sensor (for Bank 1 Sensor 1) 1.262,2.509 1.370,2.664 0.108,0.155 10 1 2.303,2.509 2.411,2.664 0.108,0.155 10 2 1.18,2.922 1.447,3.071 0.267,0.149 10 U4 1.18,3.066 3.454,3.252 2.274,0.186 10 Knock Sensor (for Bank 2 Sensor 1) 1.262,4.336 1.370,4.491 0.108,0.155 10 1 2.303,4.336 2.411,4.491 0.108,0.155 10 2 1.18,4.749 1.410,4.898 0.230,0.149 10 U5 1.18,4.892 3.454,5.078 2.274,0.186 10 Knock Sensor (for Bank 1 Sensor 2) 1.262,5.93 1.370,6.084 0.108,0.155 10 1 2.303,5.93 2.411,6.084 0.108,0.155 10 2 1.18,6.343 1.410,6.491 0.230,0.149 10 U6 1.18,6.486 3.454,6.672 2.274,0.186 10 Knock Sensor (for Bank 2 Sensor 2) 5.566,0.758 5.768,0.916 0.202,0.158 10 94 5.837,0.758 6.226,0.913 0.390,0.155 10 KNK1 5.566,1.948 5.782,2.106 0.216,0.158 10 93 5.837,1.948 6.277,2.103 0.441,0.155 10 EKNK 5.505,3.528 5.774,3.686 0.268,0.158 10 116 5.836,3.528 6.224,3.684 0.389,0.155 10 EKN2 5.545,4.166 5.757,4.325 0.211,0.158 10 96 5.836,4.166 6.224,4.322 0.389,0.155 10 KNK3 5.505,5.761 5.774,5.919 0.269,0.158 10 119 5.836,5.761 6.224,5.916 0.389,0.155 10 KNK4 5.556,5.355 5.764,5.513 0.208,0.158 10 95 5.836,5.355 6.224,5.510 0.389,0.155 10 EKN3 5.506,6.945 5.780,7.103 0.274,0.158 10 118 5.836,6.945 6.224,7.100 0.389,0.155 10 EKN4 5.502,2.339 5.772,2.497 0.270,0.158 10 117 5.836,2.339 6.224,2.494 0.389,0.155 10 KNK2 5.849,7.873 6.179,8.029 0.330,0.155 10 ECM 4.183,0.646 4.355,0.790 0.173,0.144 10 *1 0.897,7.608 1.710,7.774 0.813,0.166 10 *1: Shielded 3.169,0.84 3.516,0.996 0.347,0.156 10 CU2 3.245,0.647 3.361,0.805 0.115,0.158 10 1 3.245,1.824 3.361,1.982 0.115,0.158 10 2 3.245,2.235 3.361,2.393 0.115,0.158 10 5 3.245,3.413 3.361,3.571 0.115,0.158 10 6 3.245,4.055 3.361,4.213 0.115,0.158 10 4 3.245,5.239 3.361,5.398 0.115,0.158 10 3 3.245,5.65 3.361,5.808 0.115,0.158 10 8 3.245,6.819 3.361,6.978 0.115,0.158 10 7 4.183,2.212 4.355,2.357 0.173,0.144 10 *1 4.183,4.055 4.355,4.199 0.173,0.144 10 *1 4.183,5.638 4.355,5.783 0.173,0.144 10 *1 0.897,7.876 1.688,8.063 0.792,0.188 10 *2: for RHD 0.897,8.137 1.688,8.324 0.792,0.188 10 *3: for LHD 5.849,7.701 6.799,7.856 0.950,0.155 10 C46*2, C45*3 3.169,3.607 3.516,3.763 0.347,0.156 10 CU2 3.169,4.249 3.516,4.405 0.347,0.156 10 CU2 3.169,5.835 3.516,5.991 0.347,0.156 10 CU2 3.169,7.033 3.516,7.189 0.347,0.156 10 CU2 3.169,2.424 3.516,2.579 0.347,0.156 10 CU2 3.169,2.024 3.516,2.180 0.347,0.156 10 CU2 3.169,5.436 3.516,5.592 0.347,0.156 10 CU2

CAUTION / NOTICE / HINT

HINT:
·

DTCs P0327 and P0328 are for the bank 1 sensor 1 knock sensor circuit.

·

DTCs P032C and P032D are for the bank 1 sensor 2 knock sensor circuit.

·

DTCs P0332 and P0333 are for the bank 2 sensor 1 knock sensor circuit.

·

DTCs P033C and P033D are for the bank 2 sensor 2 knock sensor circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.INSPECT KNOCK SENSOR
U163276E01
1.091,1.124 1.385,1.294 0.295,0.170 10 C46 0.22,0.108 0.404,0.332 0.184,0.224 10 *a 0.075,1.558 0.759,1.714 0.684,0.156 10 94 (KNK1) 2.396,3.038 3.157,3.229 0.761,0.191 10 119 (KNK4) 2.511,1.548 3.194,1.703 0.683,0.156 10 96 (KNK3) 1.082,1.432 1.761,1.588 0.679,0.156 10 95 (EKN3) 0.604,3.42 1.407,3.575 0.803,0.156 10 116 (EKN2) 1.676,3.51 2.474,3.666 0.799,0.156 10 117 (KNK2) 2.029,3.252 2.785,3.438 0.756,0.187 10 118 (EKN4) 2.374,3.115 1.316,2.681 false 1.224,2.606 2.035,1.502 2.035,1.502 1.947,1.502 false 1.327,2.603 2.375,1.637 2.375,1.637 2.475,1.637 false 1.149,2.606 1.059,1.678 1.059,1.678 0.935,1.673 false 1.224,2.681 1.985,3.339 false 1.126,2.686 1.661,3.565 false 1.048,3.393 1.071,2.696 false 0.173,3.177 0.866,3.362 0.693,0.186 10 93 (EKNK) 0.591,3.167 1.063,2.606 false 1.869,1.124 2.164,1.294 0.295,0.170 10 C45 1.405,0.947 1.613,1.117 0.208,0.170 10 *A 2.178,0.947 2.386,1.117 0.208,0.170 10 *B

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C46-94 (KNK1) - C46-93 (EKNK) 20°C (68°F) 120 to 280 kΩ
C46-117 (KNK2) - C46-116 (EKN2) 20°C (68°F) 120 to 280 kΩ
C46-96 (KNK3) - C46-95 (EKN3) 20°C (68°F) 120 to 280 kΩ
C46-119 (KNK4) - C46-118 (EKN4) 20°C (68°F) 120 to 280 kΩ

for LHD
Tester Connection Condition Specified Condition
C45-94 (KNK1) - C45-93 (EKNK) 20°C (68°F) 120 to 280 kΩ
C45-117 (KNK2) - C45-116 (EKN2) 20°C (68°F) 120 to 280 kΩ
C45-96 (KNK3) - C45-95 (EKN3) 20°C (68°F) 120 to 280 kΩ
C45-119 (KNK4) - C45-118 (EKN4) 20°C (68°F) 120 to 280 kΩ


Text in Illustration
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to ECM)



OK

2.INSPECT ECM

NG

3.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
2.INSPECT ECM
a.
U162844E02
0.125,0.073 0.323,0.25 0.198,0.177 10 false *a 0.646,1.313 0.927,1.542 0.281,0.229 10 false U3 0.646,1.625 0.917,1.813 0.271,0.188 10 false U4 0.646,1.969 0.896,2.146 0.25,0.177 10 false U5 0.646,2.302 0.938,2.531 0.292,0.229 10 false U6

Disconnect the U3, U4, U5 or U6 knock sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 - 2 Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Knock Sensor)



OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the knock sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
U3-2 - C46-94 (KNK1) Always Below 1 Ω
U3-1 - C46-93 (EKNK) Always Below 1 Ω
U4-2 - C46-117 (KNK2) Always Below 1 Ω
U4-1 - C46-116 (EKN2) Always Below 1 Ω
U5-2 - C46-96 (KNK3) Always Below 1 Ω
U5-1 - C46-95 (EKN3) Always Below 1 Ω
U6-2 - C46-119 (KNK4) Always Below 1 Ω
U6-1 - C46-118 (EKN4) Always Below 1 Ω
U3-2 or C46-94 (KNK1) - Body ground Always 10 kΩ or higher
U3-1 or C46-93 (EKNK) - Body ground Always 10 kΩ or higher
U4-2 or C46-117 (KNK2) - Body ground Always 10 kΩ or higher
U4-1 or C46-116 (EKN2) - Body ground Always 10 kΩ or higher
U5-2 or C46-96 (KNK3) - Body ground Always 10 kΩ or higher
U5-1 or C46-95 (EKN3) - Body ground Always 10 kΩ or higher
U6-2 or C46-119 (KNK4) - Body ground Always 10 kΩ or higher
U6-1 or C46-118 (EKN4) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
U3-2 - C45-94 (KNK1) Always Below 1 Ω
U3-1 - C45-93 (EKNK) Always Below 1 Ω
U4-2 - C45-117 (KNK2) Always Below 1 Ω
U4-1 - C45-116 (EKN2) Always Below 1 Ω
U5-2 - C45-96 (KNK3) Always Below 1 Ω
U5-1 - C45-95 (EKN3) Always Below 1 Ω
U6-2 - C45-119 (KNK4) Always Below 1 Ω
U6-1 - C45-118 (EKN4) Always Below 1 Ω
U3-2 or C45-94 (KNK1) - Body ground Always 10 kΩ or higher
U3-1 or C45-93 (EKNK) - Body ground Always 10 kΩ or higher
U4-2 or C45-117 (KNK2) - Body ground Always 10 kΩ or higher
U4-1 or C45-116 (EKN2) - Body ground Always 10 kΩ or higher
U5-2 or C45-96 (KNK3) - Body ground Always 10 kΩ or higher
U5-1 or C45-95 (EKN3) - Body ground Always 10 kΩ or higher
U6-2 or C45-119 (KNK4) - Body ground Always 10 kΩ or higher
U6-1 or C45-118 (EKN4) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR