Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P1340  Camshaft Position Sensor "A" (Bank 1 Sensor 2)  P1342  Camshaft Position Sensor "A" Low Input (MRE)  P1343  Camshaft Position Sensor "A" High Input (MRE)  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet and MRE (Magnetoresistive Element).

The camshaft timing gear (LH) has 3 teeth on its outer circumference. When the camshaft timing gear rotates, the air gap between the protrusion on the gear and the MRE changes. The change affects the magnetic field and results in changes in the resistance of the MRE.

The crankshaft angle sensor rotor has 34 teeth and is mounted on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the G2 signal to distinguish between the cylinders, and uses the NE signal to detect the crankshaft position and engine speed.

DTC No. DTC Detection Condition Trouble Area
P1340 No camshaft position sensor signal is sent to the ECM during cranking (2 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft timing gear assembly (LH)

·

ECM


No camshaft position sensor signal is sent to the ECM with the engine speed at 600 rpm or more, or the camshaft position and crankshaft position phases are misaligned (1 trip detection logic).
P1342 Output voltage of the camshaft position sensor is below 0.3 V for 4 seconds (1 trip detection logic).
P1343 Output voltage of the camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).

A211721E04
2.827,1.419 3.206,1.599 0.379,0.181 10 GND 2.827,1.966 3.206,2.146 0.379,0.180 10 GND 0.246,1.872 0.477,2.035 0.231,0.163 10 G2 0.246,1.323 0.508,1.486 0.261,0.163 10 NE 1.108,2.472 2.049,2.649 0.941,0.177 10 20 msec./DIV. 2.708,0.749 3.274,0.926 0.566,0.177 10 5 V/DIV. 0.102,0.059 1.985,0.241 1.884,0.182 10 NE and G2 Signal Waveforms

Reference: Inspection using an oscilloscope.

Standard:
for RHD
Tester Connection Tool Setting Condition Specified Condition
C46-110 (NE+) - C46-111 (NE-) 5 V/DIV., 20 msec./DIV. Cranking or idling The correct waveform is as shown
C46-90 (G2) - C46-89 (G2-) 5 V/DIV., 20 msec./DIV. Cranking or idling The correct waveform is as shown

for LHD
Tester Connection Tool Setting Condition Specified Condition
C45-110 (NE+) - C45-111 (NE-) 5 V/DIV., 20 msec./DIV. Cranking or idling The correct waveform is as shown
C45-90 (G2) - C45-89 (G2-) 5 V/DIV., 20 msec./DIV. Cranking or idling The correct waveform is as shown


HINT:

G2 is the camshaft position sensor signal, and NE is the crankshaft position sensor signal.



MONITOR DESCRIPTION

If no signal is transmitted by the camshaft position sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Start the engine and run it at idle for 10 seconds or more.


WIRING DIAGRAM

A278622E01
1.286,2.716 2.969,2.881 1.684,0.165 10 Camshaft Position Sensor 5.369,3.043 5.728,3.208 0.360,0.165 10 ECM 5.3,0.969 5.705,1.125 0.406,0.156 10 VCV2 2.75,0.959 2.850,1.121 0.100,0.163 10 3 2.448,0.962 2.674,1.132 0.225,0.170 10 VC 2.75,1.508 2.850,1.671 0.100,0.163 10 1 2.441,1.522 2.699,1.671 0.258,0.149 10 G2 2.455,2.062 2.658,2.211 0.202,0.149 10 G- 2.783,2.03 2.900,2.193 0.117,0.163 10 2 5.3,1.508 5.557,1.657 0.258,0.149 10 G2 5.3,2.048 5.578,2.197 0.279,0.149 10 G2- 1.708,1.484 1.903,1.631 0.195,0.147 10 *1 0.127,2.951 4.563,3.144 4.436,0.193 10 *1: MRE (Outputs a voltage corresponding to changes in magnetic flux) 5.017,0.969 5.208,1.125 0.191,0.156 10 66 5.017,1.508 5.208,1.664 0.191,0.156 10 90 5.017,2.048 5.208,2.204 0.191,0.156 10 89 1.286,2.576 1.631,2.731 0.346,0.156 10 C99 5.369,2.856 6.319,3.012 0.950,0.156 10 C46*2, C45*3 0.127,3.204 0.869,3.396 0.742,0.193 10 *2: for RHD 0.127,3.456 0.869,3.649 0.742,0.193 10 *3: for LHD

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR (SENSOR POWER SOURCE)
U163270E01
0.172,0.236 0.341,0.426 0.169,0.190 10 *a 2.283,2.727 2.520,2.875 0.237,0.149 10 VC 0.432,1.921 0.744,2.102 0.312,0.181 10 C99 1.992,2.204 2.405,2.704 false

a.

Disconnect the camshaft position sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C99-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.0 V


Text in Illustration
*a Front view of wire harness connector
(to Camshaft Position Sensor)



OK

2.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ECM - CAMSHAFT POSITION SENSOR)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C99-1 (G2) - C46-90 (G2) Always Below 1 Ω
C99-2 (G-) - C46-89 (G2-) Always Below 1 Ω
C99-1 (G2) or C46-90 (G2) - Body ground Always 10 kΩ or higher
C99-2 (G-) or C46-89 (G2-) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C99-1 (G2) - C45-90 (G2) Always Below 1 Ω
C99-2 (G-) - C45-89 (G2-) Always Below 1 Ω
C99-1 (G2) or C45-90 (G2) - Body ground Always 10 kΩ or higher
C99-2 (G-) or C45-89 (G2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION
B449531E01
0.458,1.76 0.771,1.958 0.313,0.198 10 false OK 1.625,1.552 2.417,1.781 0.792,0.229 10 false Clearance 2.635,1.844 2.958,2.083 0.323,0.24 10 false NG

a.

Check the camshaft position sensor installation.

OK:

The camshaft position sensor is installed properly.




OK

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (SENSOR PLATE TOOTH)

NG

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (SENSOR PLATE TOOTH)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate teeth do not have any cracks or deformation.




OK

5.REPLACE CAMSHAFT POSITION SENSOR

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

5.REPLACE CAMSHAFT POSITION SENSOR
a.


NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Read DTCs.

Result
Result Proceed to
No DTC is output A
P1340, P1342 and/or P1343 is output B

HINT:

If the engine does not start, replace the ECM.




A

END

B