Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed and released are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, the Data List items Stop Light Switch and ST1 are both ON when the brake pedal is depressed because the characteristics of ST1 indication are the opposite of the characteristics of Stop Light Switch indication.



DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Engine switch is on (IG).
(b) Brake pedal is released.
(c) STP signal is OFF when the ST1- signal is OFF.
·

Short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A179962E05
5.83,3.17 6.187,3.326 0.357,0.156 10 ECM 5.68,0.798 6.031,0.968 0.350,0.170 10 ST1- 5.684,1.552 5.993,1.708 0.309,0.156 10 STP 5.456,0.803 5.640,0.959 0.184,0.156 10 35 5.842,3.035 6.770,3.191 0.928,0.156 10 A52*1, A38*2 5.462,1.55 5.646,1.706 0.184,0.156 10 36 4.195,1.941 4.483,2.110 0.288,0.170 10 A30 4.195,2.074 5.316,2.237 1.121,0.163 10 Stop Light Switch 4.289,0.785 4.397,0.948 0.107,0.163 10 4 5.092,1.54 5.206,1.710 0.114,0.170 10 1 3.81,1.508 3.924,1.678 0.114,0.170 10 1 5.092,0.785 5.192,0.948 0.100,0.163 10 3 4.289,1.548 4.397,1.711 0.107,0.163 10 2 4.054,1.51 4.162,1.673 0.107,0.163 10 2 3.604,0.773 3.718,0.943 0.114,0.170 10 1 3.844,0.774 3.951,0.937 0.107,0.163 10 2 3.649,1.008 3.930,1.164 0.281,0.156 10 IGN 3.793,1.765 4.213,1.920 0.420,0.156 10 STOP 2.605,1.807 2.886,1.963 0.281,0.156 10 IG2 1.428,2.437 1.785,2.593 0.357,0.156 10 IG2D 1.301,2.22 1.486,2.383 0.185,0.163 10 11 0.483,2.269 0.875,2.605 0.392,0.336 10 IG2 MAIN 3.694,3.642 3.982,3.798 0.288,0.156 10 ALT 0.651,4.791 1.140,4.974 0.489,0.184 10 Battery 2.304,2.624 2.518,2.780 0.214,0.156 10 E2 2.304,2.764 3.321,2.943 1.017,0.179 10 Main Body ECU 4.305,3.506 5.053,3.690 0.748,0.184 10 *1: for RHD 4.305,3.768 5.053,3.951 0.748,0.184 10 *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / All Data / Stop Light Switch.

(e)

Check the STP signal when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed STP signal ON
Released STP signal OFF

PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / All Data / Stop Light Switch.


e.

Read the value displayed on the GTS.

Standard:
Condition Specified Condition
Brake pedal depressed STP signal ON
Brake pedal released STP signal OFF




OK

NG

2.INSPECT STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE)
2.INSPECT STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE)
U163299E01
0.146,0.064 0.344,0.252 0.198,0.188 10 *a 0.642,0.728 0.910,0.894 0.268,0.166 10 A30

a.

Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-2 - Body ground Always 11 to 14 V
A30-4 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch)



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH)

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

4.INSPECT ECM (STP AND ST1 - VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.INSPECT ECM (STP AND ST1 - VOLTAGE)
U163720E02
1.875,3.656 2.583,3.438 true 1.781,3.646 2.573,4.365 true 1.771,0.281 1.969,0.448 0.198,0.167 10 false *b 0.219,0.281 0.427,0.469 0.208,0.188 10 false *a 0.271,2.188 0.427,2.385 0.156,0.198 10 false *c 2.677,3.354 3.281,3.531 0.604,0.177 10 false 36 (STP) 2.635,4.333 3.26,4.542 0.625,0.208 10 false 35 (ST1-) 1.125,2.677 1.417,2.854 0.292,0.177 10 false A52 1.875,2.667 2.167,2.844 0.292,0.177 10 false A38 1.438,2.417 1.635,2.615 0.198,0.198 10 false *A 2.177,2.417 2.375,2.615 0.198,0.198 10 false *B

a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RHD
Tester Connection Condition Specified Condition
A52-35 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
Brake pedal depressed Below 1.5 V
A52-36 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V

for LHD
Tester Connection Condition Specified Condition
A38-35 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
Brake pedal depressed Below 1.5 V
A38-36 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V


Text in Illustration
*A for RHD
*B for LHD
*a Depressed
*b Released
*c Component with harness connected
(ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR