Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the engine switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 Open in the ECM backup power source circuit (1 trip detection logic).
·

Open in backup power source circuit

·

Battery

·

Battery terminals

·

EFI fuse

·

ECM



HINT:

If DTC P0560 is stored, the ECM does not store other DTCs and the data stored in the ECM is partly cleared.


CONFIRMATION DRIVING PATTERN

1.

Turn the engine switch on (IG) and wait for 5 seconds or more.


WIRING DIAGRAM

U162910E01
6.239,3.147 6.609,3.317 0.370,0.170 10 ECM 5.903,2.195 6.114,2.371 0.211,0.177 10 E1 5.917,1.158 6.302,1.321 0.385,0.163 10 BATT 5.575,0.992 5.869,1.161 0.295,0.170 10 A38 5.575,2.202 5.869,2.371 0.295,0.170 10 C45 5.583,0.822 5.831,0.978 0.248,0.156 10 1*2 5.555,2.027 5.891,2.175 0.336,0.149 10 81*2 3.683,1.139 4.803,1.312 1.120,0.173 10 EFI MAIN NO. 1 0.859,2.965 1.335,3.149 0.475,0.184 10 Battery 5.228,0.992 5.523,1.161 0.295,0.170 10 A52 5.228,2.202 5.523,2.371 0.295,0.170 10 C46 5.237,0.822 5.485,0.978 0.248,0.156 10 1*1 5.209,2.027 5.545,2.175 0.336,0.149 10 81*1 2.083,2.692 2.859,2.848 0.776,0.156 10 *1: for RHD 2.083,2.958 2.859,3.114 0.776,0.156 10 *2: for LHD 1.899,1.158 2.320,1.331 0.421,0.173 10 P/I-B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the ECM connector.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
A52-1 (BATT) - Battery positive (+) terminal Always Below 1 Ω
A52-1 (BATT) or Battery positive (+) terminal - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
A38-1 (BATT) - Battery positive (+) terminal Always Below 1 Ω
A38-1 (BATT) or Battery positive (+) terminal - Body ground Always 10 kΩ or higher




OK

2.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BATTERY
a.

Check that the battery is not depleted (See page Power Source / Network>1UR-FE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION).

OK:

Battery is not depleted.




OK

3.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR BATTERY TERMINAL

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG) and turn the GTS on.


g.

Wait 5 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read DTCs.

Result
Result Proceed to
P0560 is output A
No DTC is output B



A

B