Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).

(a) Vehicle speed is 24 km/h (15 mph) or more.

(b) Engine speed is 1000 rpm or more.

(c) STA signal is on.


·

Park/neutral position switch assembly

·

Starter relay (ST) circuit

·

Main body ECU

·

ECM



CONFIRMATION DRIVING PATTERN

A231469E01
1.226,1.979 1.604,2.156 0.378,0.177 10 Idling 0.68,2.238 1.655,2.561 0.975,0.323 10 Engine Switch on (IG) 0.435,0.813 1.601,1.194 1.166,0.382 10 24 km/h (15 mph) 2.393,2.851 3.076,3.167 0.684,0.316 10 5 seconds or more 3.427,2.938 4.699,3.103 1.272,0.165 10 20 seconds or more 2.004,2.336 2.197,2.525 0.193,0.188 10 [A] 2.586,2.125 2.796,2.297 0.210,0.172 10 [B] 4.03,0.457 4.257,0.625 0.227,0.168 10 [C] 4.905,3.342 5.139,3.510 0.234,0.168 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on [A].

6.

Idle the engine for 5 seconds or more [B].

7.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0617.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A351246E01
3.781,6.764 4.678,6.933 0.897,0.169 10 *1: for RHD 3.781,7.121 4.678,7.290 0.897,0.169 10 *2: for LHD 5.672,1.042 6.134,1.242 0.461,0.199 10 NEO 1.303,1.581 1.764,1.737 0.461,0.156 10 STAR 1.391,2.094 1.853,2.278 0.461,0.184 10 STA 1.459,1.048 1.828,1.222 0.369,0.174 10 NE 0.075,2.692 2.061,3.100 1.986,0.408 10 Certification ECU Assembly (Smart Key ECU Assembly) 3.209,2.584 5.087,2.784 1.878,0.200 10 Park/Neutral Position Switch 0.596,4.579 0.821,4.737 0.225,0.158 10 ST 5.677,1.576 6.057,1.750 0.380,0.174 10 NSW 5.677,3.673 5.990,3.829 0.313,0.156 10 STA 6.097,4.957 6.447,5.127 0.350,0.170 10 ECM 3.267,4.581 3.488,4.737 0.221,0.156 10 ST 2.405,6.171 2.871,6.346 0.466,0.174 10 Starter 0.745,6.802 1.244,6.995 0.498,0.193 10 Battery 5.313,1.04 5.653,1.235 0.340,0.195 10 A38 5.294,1.572 5.659,1.789 0.365,0.217 10 C45 5.313,3.771 5.622,3.927 0.309,0.156 10 A38 5.342,0.851 5.736,1.042 0.394,0.191 10 7*2 5.224,1.378 5.665,1.553 0.441,0.174 10 120*2 5.286,3.576 5.650,3.750 0.364,0.174 10 46*2 2.561,5.036 2.689,5.199 0.128,0.163 10 3 3.212,2.435 3.604,2.618 0.392,0.184 10 C24 2.568,4.15 2.675,4.306 0.107,0.156 10 5 3.006,4.151 3.113,4.307 0.107,0.156 10 2 1.093,5.741 1.201,5.897 0.107,0.156 10 1 1.738,5.503 1.845,5.659 0.107,0.156 10 1 2.995,5.039 3.110,5.202 0.114,0.163 10 1 1.759,5.698 1.964,5.854 0.205,0.156 10 D2 1.017,5.921 1.477,6.144 0.460,0.223 10 D21 3.246,2.007 3.437,2.163 0.191,0.156 10 5 1.741,2.004 1.949,2.163 0.208,0.159 10 12 1.741,1.486 1.949,1.646 0.208,0.159 10 10 1.741,0.964 2.008,1.120 0.267,0.156 10 14 4.248,2.007 4.439,2.163 0.191,0.156 10 4 0.075,2.54 0.444,2.714 0.369,0.174 10 E128 4.916,1.045 5.256,1.240 0.340,0.195 10 A52 4.921,3.771 5.260,3.966 0.340,0.195 10 A52 4.911,1.572 5.276,1.789 0.365,0.217 10 C46 4.968,0.851 5.363,1.042 0.394,0.191 10 7*1 4.827,1.378 5.286,1.553 0.459,0.174 10 120*1 4.894,3.576 5.258,3.750 0.364,0.174 10 46*1

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.

If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Check the value displayed on the GTS when the engine switch is turned on (IG) and when the engine is started.

OK:
Condition Starter Signal
Engine switch turned on (IG) OFF
Engine started ON




OK

NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

3.REPAIR OR REPLACE HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

3.REPAIR OR REPLACE HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the PNP switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
C24-5 - A52-46 (STA) Always Below 1 Ω
C24-5 or A52-46 (STA) - Body ground Always 10 kΩ or higher


Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
C24-5 - A38-46 (STA) Always Below 1 Ω
C24-5 or A38-46 (STA) - Body ground Always 10 kΩ or higher



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Drive the vehicle at more than 24 km/h (15 mph) for more than 20 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
P0617 A
No DTC B



A

B

END