Refer to DTC P2195 (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P2195).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2237
P2240 |
Open in the circuit between terminals AF+ and AF- of the air fuel ratio sensor while the engine is running (2 trip detection logic). | ·
Open in air fuel ratio sensor (for Bank 1, 2 Sensor 1) circuit ·
Air fuel ratio sensor (for Bank 1, 2 Sensor 1) ·
ECM |
| P2238
P2241 |
·
Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) AF+ voltage is 0.5 V or less. (b) (AF+) - (AF-) is 0.1 V or less. ·
Case 2: Air fuel ratio sensor admittance is below 0.0091 1/Ω (2 trip detection logic). |
·
Open or short in air fuel ratio sensor (for Bank 1, 2 Sensor 1) circuit ·
Air fuel ratio sensor (for Bank 1, 2 Sensor 1) ·
ECM |
| P2239
P2242 |
AF+ voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (for Bank 1, 2 Sensor 1) circuit ·
Air fuel ratio sensor (for Bank 1, 2 Sensor 1) ·
ECM |
| P2252
P2255 |
AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (for Bank 1, 2 Sensor 1) circuit ·
Air fuel ratio sensor (for Bank 1, 2 Sensor 1) ·
ECM |
| P2253
P2256 |
AF- voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (for Bank 1, 2 Sensor 1) circuit ·
Air fuel ratio sensor (for Bank 1, 2 Sensor 1) ·
ECM |
DTCs P2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.
DTCs P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.
These DTCs are output when there is an open or short in the air fuel ratio sensor circuit, or if air fuel ratio sensor output drops.
To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the engine switch on (IG), and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is outside of the specified range, or the admittance is below the standard value, the ECM will determine that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in the next driving cycle, the MIL is illuminated and a DTC is stored.
The air fuel ratio sensor varies its output voltage in proportion to the air-fuel ratio. If the air fuel ratio sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short in the air fuel ratio sensor circuit.
Start the engine and wait for 5 minutes or more.
Refer to DTC P2195 (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P2195).
Refer to "Data List / Active Test" [AFS Voltage B1S1 and AFS Voltage B2S1] (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-1 (HA1A) - C46-22 (HA1A) | Always | Below 1 Ω |
| C22-3 (A1A+) - C46-126 (A1A+) | Always | Below 1 Ω |
| C22-4 (A1A-) - C46-125 (A1A-) | Always | Below 1 Ω |
| C23-1 (HA2A) - C46-20 (HA2A) | Always | Below 1 Ω |
| C23-3 (A2A+) - C46-103 (A2A+) | Always | Below 1 Ω |
| C23-4 (A2A-) - C46-102 (A2A-) | Always | Below 1 Ω |
| C22-1 (HA1A) or C46-22 (HA1A) - Body ground | Always | 10 kΩ or higher |
| C22-3 (A1A+) or C46-126 (A1A+) - Body ground | Always | 10 kΩ or higher |
| C22-4 (A1A-) or C46-125 (A1A-) - Body ground | Always | 10 kΩ or higher |
| C23-1 (HA2A) or C46-20 (HA2A) - Body ground | Always | 10 kΩ or higher |
| C23-3 (A2A+) or C46-103 (A2A+) - Body ground | Always | 10 kΩ or higher |
| C23-4 (A2A-) or C46-102 (A2A-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-1 (HA1A) - C45-22 (HA1A) | Always | Below 1 Ω |
| C22-3 (A1A+) - C45-126 (A1A+) | Always | Below 1 Ω |
| C22-4 (A1A-) - C45-125 (A1A-) | Always | Below 1 Ω |
| C23-1 (HA2A) - C45-20 (HA2A) | Always | Below 1 Ω |
| C23-3 (A2A+) - C45-103 (A2A+) | Always | Below 1 Ω |
| C23-4 (A2A-) - C45-102 (A2A-) | Always | Below 1 Ω |
| C22-1 (HA1A) or C45-22 (HA1A) - Body ground | Always | 10 kΩ or higher |
| C22-3 (A1A+) or C45-126 (A1A+) - Body ground | Always | 10 kΩ or higher |
| C22-4 (A1A-) or C45-125 (A1A-) - Body ground | Always | 10 kΩ or higher |
| C23-1 (HA2A) or C45-20 (HA2A) - Body ground | Always | 10 kΩ or higher |
| C23-3 (A2A+) or C45-103 (A2A+) - Body ground | Always | 10 kΩ or higher |
| C23-4 (A2A-) or C45-102 (A2A-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Allow the engine to idle for 5 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output | B |
A
B