Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0550  Power Steering Pressure Sensor Circuit Malfunction  P0552  Power Steering Pressure Sensor Circuit Low Input  P0553  Power Steering Pressure Sensor Circuit High Input  


DESCRIPTION

The power steering oil pressure switch is turned on when a power steering wheel load is generated by turning the steering wheel. The ECM regulates the engine idling speed according to the voltage output of the sensor.

DTC No. DTC Detection Condition Trouble Area
P0550 Power steering oil pressure switch voltage is below 0.28 V, or higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
·

Open or short in power steering oil pressure switch circuit

·

Power steering oil pressure switch

·

ECM


P0552 Power steering oil pressure switch voltage is below 0.28 V for 0.5 seconds while the engine is running (1 trip detection logic).
·

Open or short in power steering oil pressure switch circuit

·

Power steering oil pressure switch

·

ECM


P0553 Power steering oil pressure switch voltage is higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
·

Open or short in power steering oil pressure switch circuit

·

Power steering oil pressure switch

·

ECM



WIRING DIAGRAM

A278621E01
0.14,2.682 0.449,2.879 0.309,0.198 10 C59 0.133,2.836 2.375,3.010 2.242,0.174 10 Power Steering Oil Pressure Switch 5.618,3.305 5.962,3.468 0.343,0.163 10 ECM 5.625,0.987 6.024,1.135 0.399,0.149 10 VCV1 5.618,3.134 6.531,3.283 0.913,0.149 10 C46*1, C45*2 5.38,0.987 5.557,1.135 0.177,0.149 10 67 5.374,2.09 5.562,2.239 0.188,0.149 10 98 5.625,1.554 5.985,1.703 0.360,0.149 10 PSP 5.625,2.095 5.823,2.261 0.198,0.166 10 E2 1.359,0.994 1.584,1.142 0.225,0.149 10 VC 1.317,1.561 1.649,1.710 0.332,0.149 10 PSP 1.387,2.102 1.585,2.268 0.198,0.166 10 E2 1.682,2.072 1.790,2.242 0.107,0.170 10 3 1.667,0.97 1.768,1.140 0.100,0.170 10 1 1.677,1.542 1.798,1.705 0.121,0.163 10 2 5.374,1.536 5.551,1.685 0.177,0.149 10 72 3.363,2.752 4.102,2.915 0.739,0.163 10 *1: for RHD 3.363,3.011 4.102,3.174 0.739,0.163 10 *2: for LHD

MONITOR DESCRIPTION

The ECM monitors the switch voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure switch and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Idle the engine for 5 seconds or more.


CAUTION / NOTICE / HINT

HINT:
·

If other DTCs related to different systems that have terminal E2 as the ground terminal are stored simultaneously, there may be an open circuit between terminal E2 and body ground.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [Power Steering Signal] (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SWITCH)
a.

Disconnect the ECM connector.


b.

Disconnect the power steering oil pressure switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C59-2 (PSP) - C46-72 (PSP) Always Below 1 Ω
C59-1 (VC) - C46-67 (VCV1) Always Below 1 Ω
C59-3 (E2) - C46-98 (E2) Always Below 1 Ω
C59-2 (PSP) or C46-72 (PSP) - Body ground Always 10 kΩ or higher
C59-1 (VC) or C46-67 (VCV1) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C59-2 (PSP) - C45-72 (PSP) Always Below 1 Ω
C59-1 (VC) - C45-67 (VCV1) Always Below 1 Ω
C59-3 (E2) - C45-98 (E2) Always Below 1 Ω
C59-2 (PSP) or C45-72 (PSP) - Body ground Always 10 kΩ or higher
C59-1 (VC) or C45-67 (VCV1) - Body ground Always 10 kΩ or higher




OK

2.REPLACE POWER STEERING OIL PRESSURE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE POWER STEERING OIL PRESSURE SWITCH
a.

Replace the power steering oil pressure switch (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>POWER STEERING OIL PRESSURE SWITCH>REMOVAL).



NEXT

3.CONFIRM WHETHER DTC OUTPUT RECURS
3.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


e.

Read the DTCs.

Result
Result Proceed to
P0550, P0552 and/or P0553 is output A
No DTC is output B



A

B

END